Yamaha FZR 1000 Exup Full engine restoration Part 3

[@Maxik_Bartos]

Thank you for the detailed information. Crankshaft bearing designation. 👍👍

[@lubomirkapri3843]

Thanx you are awesome! I have two FZR and this is exactly that what i need!

[@ChrisSofos]

Thank you for your comment! Enjoy your awesome motorcycles 😉

[@uhtred7860]

To anyone rebuilding an earlier 87/88 FZR 1000/750 with the FZ 750 based engine, instead of pulling the shaft out like Chris did @ 0:35 you will need to thread a long bolt into the shaft and use a slide hammer to get the shaft out. (I just put the bolt thru a large socket and slid the socket along the bolt as a make shift slide hammer) This is because one the earlier engines the bearing is a tighter pressed in fit. Also there is no pin shown at 0:59 on the earlier engines, everything else is pretty much the same.👍😀

[@ChrisSofos]

That is a very good info mate. Thanks for pointing out all these differences between these models 👍

[@jacquessmit7479]

Again so helpful thank you very much

[@ChrisSofos]

It is my pleasure!

[@dbrhdwk1239]

Very nice, I have to assemble the engine of the FZX700, I was confused to read the numbers of the crankcase upside down. Thank you very much,

[@ChrisSofos]

You are welcome! Glad to be of help!

[@gadourrekik2895]

Salut C'est possible mettre tes vidéos en sous titres en français s'il-vous-plaît

[@ChrisSofos]

I wish I could. But then that would be unfair for people speaking other languages.

[@gadourrekik2895]

@@ChrisSofos je comprends bien, resté avec l'anglais , mais vous pouvez mettre dans votre réglage vidéo en sous titres pour toutes les langues , comme ça les gens apprécié bien et comprends mieux

[@ChrisSofos]

@@gadourrekik2895 Let me try that...

[@luisfurtado5584]

Buenas amigo soy de Uruguay y tengo una Yamaha fzr 1000 consigo solo los metales de bancada de 1 color solo se puede armar así o es muy peligroso muchas gracias

[@ChrisSofos]

I'm not sure what you are trying to say. If you mean that you only change one out of the two bearings, then it's not a good idea. You better change both up and down.If you mean that you can only find one color of bearings and this is what you want to put in all of them, then the answer is no. You MUST put the exact color the manufacturer says, otherwise the engine will be destroyed.

[@luisfurtado5584]

@@ChrisSofos muchas gracias claro mi moto lleva 4 color marrón y 6 negros según tu video, y yo solo consigo acá los 10 metales de bancada marrón y mi pregunta es si podía armar con todos marron xq no consigo negro

[@ChrisSofos]

@@luisfurtado5584 Unfortunately you'll have to find the correct colors for each one of them. NEVER put different color bearings. This will destroy the engine. Good luck with your FZR!

[@luisfurtado5584]

@@ChrisSofos otra pregunta amigo el color de cojinete más grueso es el amarillo ?

[@ChrisSofos]

@Luis Furtado that is correct! If you watch my latest video (part 9) I make a mention about it.

[@user-br6lt8jl5j]

ممتاز جدا نفس الكرنك بتاع الياماها fz750مع إختلاف المقاس من فضلك ممكن أرسلك على الوتساب أنا ميكانيكي ياماها

[@ChrisSofos]

Thank you! Send me your number on my email and I'll add you on whats app. My email [e-mail]

[@user-br6lt8jl5j]

@@ChrisSofos شكرا يا كريس

[@uhtred7860]

How many Km/miles had this engine done?

[@ChrisSofos]

Not many. Around 75.000km