Yamaha Grizzly 350 Clutch / Belt Install *don't screw this up*

We are replacing and installing the clutches/belt on the Yamaha Grizzly 350. You'll want to watch until the end (most people will mess this up)
Amazing Overview of the Yamaha Grizzly 350: • Yamaha Grizzly 350 Ov...
Full Service Video: • Yamaha Grizzly 350 - C...
Flywheel Puller: ebay.com/itm/332997722043
Oil Change Kit: amzn.to/3q5fIdl
Steal of a Deal on Tires: amzn.to/3bMJsGF
Don't go without a GOOD AIR FILTER: amzn.to/3bMJsGF
Carb Kit: amzn.to/3b3iVG3
Mid Nebraska Motorsports YT
PO Box 23
Central City, NE 68826
VENMO is: @midnemotorsports
Check out my eBay store at: stores.ebay.com/midnebraskamotorsports
Shop for parts at: midnebraskamotorsports.com
Instagram: / midnebraskamotorsports
Patreon: / midnebraskamotorsports

[@brewsterly2927]

Great walk-through very easy to follow, thank you.

[@kevinturco9077]

Yes always informative

[@ezechielroy859]

always very good videos!

[@AlbertoClave]

Thank you !!! Very helpful

[@francescopasquetto2637]

Nice video. Well explained. Thankyou

[@justinlong977]

appreciate you for doing the exact bike I have.

[@1978punisher]

Love your video help a lot

[@matt9264]

Thank you

[@rideshy3594]

Your videos are great ! I need advice ; Yamaha Bruin 350, 2005, I bought new. This year I’ve noticed a slight lag when going from neutral, as I increase the throttle above idle a slight clank is noticeable then no problems. Tranny seems to lock in and pull fine once it locks in gear (fwd or rev). Is my belt worn out, is it a clutch issue, or what ?

[@johnhenderson299]

Great video

[@alittlebitofannythingandev7919]

Hey, I have a 2014 yamaha grisly 350, do you think that the setup is the same, or do you think that i would have to use/get different parts?

[@kevinwren4152]

In the video you said there were five bolts in the primary clutch cage, I’m only seeing four. Am I missing something because it WILL NOT come off

[@franciscoj.v.5795]

What would be a reason for removing the belt?

[@joegobelko9965]

Hi! My primary clutch has quite a bit of brake dust looking substance in it, around it, and on the cover, does that mean it’s bad? Otherwise how can I figure out what clutch is bad

[@hillbillymitchswhitetailst6215]

What would cause a Kawasaki prairie 400 wont go past 25 mph.belt deflection is 29mm carburetor is working properly slide is fine jets are all clean replaced stock jets with same size jets .fuel level in carburetor is speck.wheels free spin no locked up brakes new belt was put on still have the problem wont go past 25 even cleaned the sheves with Scotch Brite pad .can you help please thank you

[@gunterb4376]

hallo kann mir jemand helfen ich habe vom freund eine Yamaha Bruin 350 4x4

[@As130thps]

Can I get a link to the bearing that goes in the clutch guard/cage. I believe that’s the source of the whining I’m experiencing on my 2004 bruin

[@ezechielroy859]

hey i have a question... how to you remove the front drive shaft on a yamaha big bear (I have a 1994)... do you ha ve to take the u joint apart first?

[@ronaldnoeortizbueno]

Quiero las medidas

[@pablocamachojimenez4994]

Hello, thank you very much for your videos.