Yamaha R7 Spiegler Stainless Steel Brake Lines Install | Sportbike Track Gear

[@IslandTosh]

So glad my Triumph came w SS braided lines from the factory.

[@sportbiketrackgear]

IMO all the bikes should come with them. - Van

[@mikeskidmore6754]

Do you really need stainless steel brake lines? The rubber flexes a little thus makes brake application a little more Progressive.. My Yamaha FZ-07 does not have them while my 2008 Buell Ulysess does have them.. I use one finger on both bikes..

[@NendoCrescendo]

Awesome lines, just bought from you guys!! Awesome shirt as well, good artist!

[@sportbiketrackgear]

Thanks for the business and enjoy the new brake lines. Great mod for sure. - Van

[@moStallion]

I loved the shirt. Staind is my favorite rock band

[@sportbiketrackgear]

Aaron Lewis is one of my favorite artists for sure. Thanks for watching! - Van

[@NeptuneBluez]

This is an excellent how to video. Thanks Brian Van!

[@sportbiketrackgear]

You are welcome and thank you for watching! - Van

[@davidstatham7760]

Another great video & those lines look awesome 👌 👍.

[@sportbiketrackgear]

Thank you for watching! - Van

[@wkdravenna]

Looking good ! Yamaha looks alright too.

[@sportbiketrackgear]

Thank you for watching! - Van

[@danielkerekes9613]

Your the best!!! Thank you so much!!

[@sportbiketrackgear]

You are welcome and thank you for the kind words. - Van

[@texasjedi8680]

Hey Brian, I need to get a full set of street fairings for my 2017 R1.What is the best website or manufacturer that you recommend sir? Your input would be much appreciated man.

[@sportbiketrackgear]

Sorry I do not have an answer for this. I have never replaced the street fairings on any of our bikes. - Van

[@texasjedi8680]

@@sportbiketrackgear No worries,thanks for the prompt response. I purchased red Spiegler lines for my R1 from y’all and referenced the install video as well. Always great products,customer service and how-to videos. Ride safe🙏

[@adamhause5529]

How do you put more fluid through the lines when your front brake is limp?

[@mikeskidmore6754]

My Yamaha FZ-07 rear brake pedal has way too much Travel. When I adjust it the way I like it then the brake light will not come on. There are many adjustments but I just can't seem to get it adjusted to the brake light will come on when it should. I was thinking of replacing all of the mechanic brake light hardware with a brake light pressure switch .. Have you done that? I suppose it would take some fittings and adaptors to plumb it ..

[@sportbiketrackgear]

If there is excessive travel in the brake pedal you may still have air in the system. I would try bleeding the system again to see if that solves your problem. If you want to remove the mechanical switch and install a banjo bolt brake line switch that is a relatively easy process. Essentially all you need to do is replace the banjo with the banjo with the pressure switch built into it and connect the 2 wires. - Van

[@mikeskidmore6754]

@@sportbiketrackgear Thanks for the reply but it's the linkage adjusments.. I can adjust the brake pedal so the travel is short like it should be but then the brake light won't go on.. So of course I always use the front brake too . I had a rear wheel bearing go out on my 2008 Buell Ulysses.. I just installed a new rear tire .. I noticed one wheel bearing was a bit dry. I recorded the part numbers.. It's ciaous to find the correct wheel bearings.. Prices from $15.00 to $60.00 each at Motion Industriws was $60 for rears and $50 for front wheel bearings. Finally I found an ATV parts supplier that both my front and rear wheel bearings in stock . Also front seals .. which I don't recall seeing when I changed the front tire nor are they shown in my 2008 Buell parts book. I thought about calling you guys but figured it was not something you had in Stock .. I did purchase the Michillen Road Piolot VI tires from STG and the handling is night and day better over the worn out Perelli that was rock hard and worn more on the sides with a rib in the middle and worn down so much more on the left side I thought maybe the forks were bent. I guess the left side wears more due to the crown in the road. The 4 bearings and two seals for the front wheel were $51.47 with Free shipping .. In 2010 Buell went to a much larger wheel bearing. I doubt it would be feasable to find a 2010 rear wheel and the proper center axle spacer..

[@maya00795]

Helpful tips....... too good 👍🏻👍🏻🆒

[@sportbiketrackgear]

Thank you for watching! - Van

[@michaelneal7079]

those lines look sweet

[@sportbiketrackgear]

Thank you for watching! - Van

[@lildrippy8252]

I got the non Abs lines for my r7, what am I supposed to do with me abs module? And how can I make sure my speed sensor will still work?

[@sportbiketrackgear]

FlashTune ABS Delete Plug Yamaha YZF-R7 2022 www.sportbiketrackgear.com/flashtune-abs-delete-plug-yamaha-yzf-r7-2022/

[@emilianohuerta4817]

Do you happen to know the torque spec for the nuts on the brake line

[@sportbiketrackgear]

I do not but can tell you each kit includes a full set of instructions. - Van

[@yzfr1owner]

If this was the WERA forum someone would already bust your balls about "break" vs "brake" 😆

[@sportbiketrackgear]

Let's just say I do not make the titles or the thumbnails... - Van

[@knockout6814]

Never showed the gas tank reinstall

[@sportbiketrackgear]

Sorry, it is pretty simple. I thought we had that covered in the OEM bodywork video. - Van

[@1990-t1j]

Thumbs up but a bit too long for me to sit through.

[@sportbiketrackgear]

This one is meant for the R7 riders who need this to install their line kits. - Van

[@djkellyflavour5481]

Not gonna happen unless I'm taking it to a professional way too complicated for me

[@sportbiketrackgear]

For sure it is best to take it to a professional if you are not comfortable with the project. - Van