Yamaha Raptor 660 Dynojet Kit Installation

[@alanlyons1195]

How does the amazon carb work now that you have added the dynojet kit? Is the carb functioning correctly at all rpm's? Everything good now?

[@JOATD]

It runs okay it's not the best but once I put that number 25 jet in there it runs a lot better

[@Kevin_Yagoonie]

Great video I'll be doing the same dynojet settings with a #25 pilot

[@JOATD]

Yeah that # 25 pilot really matters with these 660, let me know how it turns out

[@Kevin_Yagoonie]

@@JOATD will do 👍

[@Kevin_Yagoonie]

​@@JOATDhow come you didn't cover settings for a open airbox lid? I have slip on K&n filter no airbox lid Below 1000 elevation Dyno jet needles 3rd clip 25 pilots Dynojet 146/148 Screws at 3 turns out. Has a bog flat spot at 3/4 throttle when I pin it Fully rebuilt OEM Mikuni carbs Everything in the carbs are replaced New carb boots. No air leaks

[@erikaolivis4211]

My Raptor has a stock exhaust with 145 left jet,150 right jet, and 22.5 pilot jet. Needle jet is on the 3rd notch. Do I need to change my pilot jet to a #25 and move the needle jet to the 4th position? How many turns out for fuel screws? Thanks for your help.

[@NaSTI_Evolution]

Crazy the DJ costs 100 bucks and it doesn’t include the pilots! I have full exhaust and an intake and need to run with choke or else it’s so lean and will stumble and pop. Jet kits can be had for 20 bucks, is the needle really worth it?

[@alanlyons1195]

Are you sure that you have a full exhaust? It looks like a stock header pipe to me, but what do I know!

[@JOATD]

Come to find out it was a stock header but the slip on is not stock. I bought it from someone they told me that it was but once I started doing my research I realized that it was not but I had already created the video. The carburetor ran funny and then once I switched that jet out to a number 25 it's fine now even though it's not a full exhaust

[@enor1sdca]

Was your airbox lid on or off?

[@JOATD]

My airbox lid was on

[@enor1sdca]

@@JOATD okay thanks man DJ does not indicate that for me. And with your configuration you ran right? Or did you end up changing anything?

[@JOATD]

I had to make slight modifications but it ran

[@ben.rodriguez6897]

Could u rev the motor couse my bike starts and idles fine but one i rev it it back fires

[@JOATD]

Normally when it backfires it means that it's getting too much gas.

[@Blockhead_teda]

What part of nc you in ? I’m in Va 😂 I’ll drop this raptor off to you, cause this shit stressing me out .. star up and idle perfect mid range throttle good too . Full throttle boggin

[@yort3964]

What if I have a full exhaust with no baffle and I’m below 3000 feet what do you think I should use?

[@JOATD]

I would still start with DJ 146 left /// DJ 148 right below 3,000 ft

[@AlexKW777]

👍💪

[@JOATD]

Thank you, I'm glad my video could help

[@thotty2hotty530]

Quick question bro I’m trying to take off the carb but their is 2 cables on the left side of the carb connected and I can’t figure out how to take them off

[@JOATD]

Give me one second and I got you

[@thotty2hotty530]

@@JOATD appreciate it

[@JOATD]

@@thotty2hotty530 It's a Black plastic screw on the left side of the carb, just in front of the throttle cable. I think it's a 12mm, just undo that, and on the end of the cable there's a spring assembly. The throttle cable is a little more tricky you have to turn the spring mechanism to the left hold it and take a screwdriver or right angle Pick.

[@JOATD]

Part 2, and pull out towards you the brass pin that holds the cable then maneuver the rest of the cable around the spring tensioner. And the same way you took it out you have to put it back in

[@JOATD]

@@thotty2hotty530 part 3 here is a guy walking you through it. kzbin.info/www/bejne/jnuYoYV_nrNlr5Y

[@mid-ohioguardian6927]

Why does the dynajet kit come with a new needle ??? Thank you

[@JOATD]

Yes it does

[@jasonrivera8981]

I keep having carb issues. You have an email I can contact you in?

[@JOATD]

All contact information is in the descriptions area