Your Handy Dandy QUICK START GUIDE - Mooer GE 300

[@DZ-paulaugu]

thanks Joe keep up the good work

[@belgiandip8682]

Super helpful! Very clear, concise and easy to follow. Thanks!

[@vimfuego8827]

"Super helpful! Very clear, concise and easy to follow. Thanks!" Oh FFS, this sounds like a paid comment and the video didn't even demonstrate any sound. Very poor channel.

[@sirvicemanone]

Some very useful info i never realized about my ge300 thank you so much

[@brotherplucker2]

Keep up the good work! This is valuable.

[@NurbariaJaalam]

best tutorial so far well explained.

[@BarryGrueter]

Nice review thanks for sharing 👍

[@chrisdaviesguitar]

how sturdy is it? a very useful post, thank you.

[@finnishforce5094]

Thank you again! This is the video I have been searching for!

[@emerinahmetasevic]

Thank you. You helped a lot.

[@regplasma7906]

Nicely done Jon.

[@HowardWatts1]

Brilliant! Many thanks, this is very helpful!

[@AveyroadOfficial]

thank you so much for this tutorial. gonna save me a lot of time if I got for this unit - not decided yet.

[@gbrt9569]

Useful video, thanks for sharing

[@rohitpillai1]

Superb video mate!!!!

[@JSBroadcast]

Great stuff man, thanks for the video.

[@Гитар-клаб]

Thank you very much! very useful video!

[@Nhask666]

Great video! Thanks!

[@hxshreds]

Can you plug this straight to a cab? Great video!

[@ChopsUK]

Hi Jon, your videos are always very helpful especially with my PODHD500x so thank you so much. My only issue with PODHD500x is I cant use the PODHD software as a plugin/VST like I used to with PODFARM. With that in mind I am close to buying this MOOER GE 300 however the question is, can you use the MOOER software as a plugin/VST in the daw?

[@woodyoulove-reynaldguibone6890]

Can we assign multple fx or parameter to a single ctrl footswitch?

[@ZenT8055]

heyy, can you use two amps in the chain?? example ac30 and blues jr. is it possible?

[@nikosdimitrakopoulos7902]

Good morning!!I have a question!!if I connect my ge300 from xlr to a mixer,where can I connect a monitor??in xlr right or somewhere else??

[@thearoom]

Can you run two of the same pills next to each other say I want one delay and I want the same delay next to it with a different speed the same with two overdrives or two distortions same in the signal chain but differing settings and you can switch back and forth? Is that possible

[@henri9083]

Is there an option to setup dual amps on this GE300?

[@DannyDoesGuitar]

wait that's not a Pod HD500X. what's going on here.

[@willygoat4113]

Is there any disadvantage to running the amp modeler into an interface vs plugging direct into computer?

[@turunturun]

I know your question is 4 months old, but I’ll put my opinion in here for you. I’ve not A/B’d to confirm this but my guess is the difference won’t matter unless you have a very bad interface. Since this is a digital unit, my guess is that once the GE300 converts your analog input signal to digital, it never converts it back to analog if you use the USB plug to get the signal into your DAW. If you use an interface however, you’ll be connecting it with analog cables at which point you’ll be having the GE300 convert the digital signal back into analog, then having that analog signal travel along analog cables which are more susceptible to external noise then having your interface convert the analog signal BACK into digital. Obviously this is theoretically significantly worse than having the GE just send a digital signal straight into your daw via USB. The only exception to my comment would be if you chose to use the digital out on the GE300, which should fundamentally be identical to using USB at least in audio quality. Hope that’s helpful.

[@iambear.6526]

You said there was 3 pedal board modes, you only talked about one?

[@saltyhose8257]

No more hd500x videos ?

[@uks0172]

first

[@vimfuego8827]

"Super helpful! Very clear, concise and easy to follow. Thanks!" Oh FFS, this sounds like a paid comment and the video didn't even demonstrate any sound. Very poor channel.

[@SamVieiraGuitar]

It gives me anxiety listening to your out of tune guitar

[@bikersoncall]

So you have to save an edited Preset into the factory bank area, overwriting whatever FACTORY slot you want to save it in? This is the most ridiculous place to save a User Patch , NO USER BANKS? Total Waste of time.

[@mihnea358]

you have more than 64 user banks