How to Make an induction Heater, 2kw induction Heater

How to Make an induction Heater, 2kw induction Heater
👉Get a free trial of Altium Designer with 365 and 25% off your purchase :
👉 www.altium.com/... 👈
👉Learn about Altium 365, the electronics product design platform that unites PCB design, MCAD, data management, and teamwork: 👉 www.altium.com...
👉Free search engine for the best quality components from Octopart:
👉www.octopart.com
👉 The soldering iron I use
👉 bit.ly/40yqigF
👉Circuit Diagram
👉drive.google.c...
**Thank you for watching me. To help the video reach more people, please remember to like, comment, and share it. If you haven't subscribed yet, you can support the channel by subscribing for free. Your feedback will help this video reach more people, and encourage me to find more resources to produce higher quality and new content for you Take care of yourself until we meet again in the next video and project. ***
#altium
#zaferyildiz
#heater
#40n60
#diyproject
#electronics

[@سیدعلیاکبررضوی]

درود..واقعازیباست کارت دوست خوبم.من تازه افتخارآشنایی باشمانسیبم شده.ممنونم🎉🎉🎉

[@warrenkeillor9034]

Thank you! I have a blown unit from China that is similar, but the chips had the numbers sanded off. Mine works great, with Tesla pan cake coils, and can run large Dc motors. Adding capacitors and schottky diodes bridge gets over 378 volts DC output. Good fun! ( a copper foil output coil was a bad idea) Cheers Warren

[@ianbatty3947]

12 V supply, 2 kilowatts will demand over 160 (!) amps. No way the clip leads can carry that much current. Nice idea, but don't believe the 2 kW. For comparison, a car starter motor draws under 100 A at 12 V.

[@des.enterrado]

Este circuito se ve mucho en internet, es un oscilador que a la vez es driver ZVS y realmente funciona muy bien. Es obvio que ni de broma obtienes 2kW a 12V pero con el mismo tipo de circuito, otros componentes y mas tensión, nada que no se pueda hacer :P

[@АлексейСивоконь-р5к]

Hi, where did you get 2kw number? If it runs with 12v, current should be almost 170 Amps!!!

[@yvancoissieu7390]

Bravo! C'est super, car vous donnez les informations ❤👍😄

[@jeetkumarchandjkc7115]

Nice vedio,However seems incomplete without providing the information regarding the input current / voltage supply.

[@suleymanselvi5132]

şunların üzerine malzemelerin adınıda yazsanız ne güzel olacak o koyduğunuz sarı şey bantmı mesela ?

[@dubab.249]

induction cooker €22 + made of square iron pipes 20*20 mm, welded a square loop 20*20 cm, let water through it, added thermal switches, thermovalves, pressure safety valves, a pump for central heating and with 1000 W I heat an apartment of 100 m2. Added more converter 12-220, 1000W, solar collectors 1500W, battery 12 v 200 A and works

[@ivicatopic6868]

BRAVO! You made a perpetuum mobile!

[@MehmetHulk]

Abi herhangi mosfeten yapılıyormu🤔

[@НиколайСнигирев-ч9э]

Паяльничек бюджетный! 👍

[@christopherwilliamdodd236]

Need to pull this to bits a little. The 'G40N60 IGBT's are rated at 625 Watts each but not your circuit. The 10K resistors are colour coded for 100K. The green choke is intended for noise supression not as a power inductor (totally different permubility). You can use any size of coil and alter the capacitors so that the resonant frequency is within the range of the IGBT's.

[@ajatsingle1703]

बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट । पूरा का पूरा बकवास कर रहा है । उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा

[@ajatsingle1703]

False. Totally false. How and from where you are drawing 166 Amp current ? Have you any reply. So stop showing such false sense.

[@malectric]

The 10k resistors are colour-coded correctly. The common mode choke he's using as a saturable centre-tapped inductor is demonstrably suitable - it has a high permeability core. It determines the switching frequency to a large extent.

[@jessiepooch]

Wrong.

[@christopherwilliamdodd236]

Brown Black Orange for 10k, he is using 100k Brown Black Yellow. Learn your magnetics. @@malectric

[@RPastuch]

2,000 watts at 12VDC equals 166 amps !!! And you use cheap thin clip leads. LOL to the max.

[@HVA08]

No, this circuit can output more than 60V and 200A across the coil when running it at full power due to resonance

[@ajatsingle1703]

बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट । पूरा का पूरा बकवास कर रहा है । उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा ।

[@ajatsingle1703]

False. Totally false. How and from where you are drawing 166 Amp current ? Have you any reply. So stop showing such false sense.

[@HVA08]

@@ajatsingle1703 well, believe me or not but if you put an AC signal into a resonance circuit with the exact frequency, the voltage and current across a resonance circuit will rises to infinity if there no resistance This circuit works like an pendulum and 2 mosfet act like 2 hand pushing it every oscillating cycle

[@عادلابومحمدلتأسيسالكهرباءوالصح]

لا

[@solarEnergy-777]

It's very nice to look at your work. Thanks for the wiring diagram.

[@ajatsingle1703]

बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट । पूरा का पूरा बकवास कर रहा है । उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा

[@tahaberber890]

Daha güçlü olması için ne yapabiliriz daha fazla isitsin istiyorum ve uzun süreli kullanım yapicam ne tavsiye edersiniz

[@EntifIya]

Sérieusement j'ai cherché fatiguer 😅mais tu m'a éclairé merci beaucoup 🎉❤❤❤🙏🙏🙏🙏

[@rezatavan5048]

سلام بسیار ،ممنون❤❤❤

[@grigkup7484]

Мощность на выходе всегда, ВСЕГДА ниже потребляемой. Мощность в 2000 вт означает что при напряжении питания в 12 вольт ток питания около 160 ампер. Провода, которыми подключили схему сгорели бы в три секунды! Они выдерживают 10 ампер и то кратковременно. Значит мощность не более 100 вт. Кто сомневается проверьте максимальныцъй ток транзисторов.

[@МирагорВ]

Люблю на заграничных видео читать русские комментарии. Русские парни как всегда правы

[@R9HAZ]

да это такой же балабол как и индийцы. только этот по изделиям не балаболит :D реально собирает рабочие схемы.

[@maquinaseartesanatos1090]

Boa noite ,só serve para materiais ferrosos ou conseguiria montar um pra p.v.c por exemplo

[@rul-p3t]

Thank you! Is it possible to wind an induction coil with a diameter of 10 - 15 centimeters to boil water?

[@mehdi6845]

Can i use Z44n instead 40n60?

[@Like_av1]

Nice video

[@hafizkhuram6517]

Jazakallah for information

[@akdhiman1946]

IExcellent job done

[@FishingNOutdoorFun]

greta sharing

[@thangnguyenvan2666]

Tôi vẫn chưa hiểu cái mạch này lại diode ở tần số thấp mà không phải là diode ở tần số cao nhỉ

[@smartfarming111]

Make video of variables frequency drive for solar to run 3 phase motor

[@tekinakyol1508]

Zafer bey ellerinize sağlık video larınızı izleyerek yaptığım indüksiyon ısıtıcı ile Erzincan da 2765 watt ile kömüre veda ettik sizi severek takip etmeye DEVAM ediyoruz

[@muhammetakgoz2996]

Kömüre veda ettik derken ne anlamda usta ne yaptığınızı anlatırmısınız rica etsem?

[@tekinakyol1508]

@@muhammetakgoz2996 yaptığımız sistem ile 2750watt saat elektrik ile günde ortalama 8 saat yâni kombi gibi ısıyı yakalayınca sistem kapanıyor sistemdeki su 10 derece soğuyunca tekrar çalışıyor bu şekilde kömürün her türlü derdinden kurtulduk

[@muhammetakgoz2996]

Rüzgar gülünden elektirik alırsan bedavaya ısınırsın ama sessiz yap malum vergi kaçırdın diyip içeri almasınlar :) Bu diğer videolarda ki gibi demir boruyu indiksiyon bobinin içinden geçiriyorlar o şekilde ısıtıyor değilmi?

[@alisan8962]

Kaç amp. Çekiyor

[@herbertkaiser6243]

Übrigens , Leistung ist Spannung * Strom. Wenn die Spannung grösser wird verringert sich der Strom ohne das mehr Leistung aus der Batterie oder ähnlich kommt.

[@jangidpradeep3131]

It is very nice

[@barthchris1]

Beautiful job with the vid! I have a hard time believing it can output 2kw though.

[@Didi1.275]

You're right. 2000 Watts by 12 Volts are 166 Ampere. The connection with crocodile clips does not even manage 50 amps

[@paradiselost9946]

@@Didi1.275 yup. and they also cant explain how the number of turns affects the power that will be delivered to the workpiece as its just a transformer reflecting impedances at the square of the turns ratio... im running one off of 150V, and i can actually get a genuine 2kw.... no clickbait required. the really interesting part about this? first... a g40n60 is an IGBT. and ZVS oscillators dont work with IGBTs... then theres those diodes. 1n4007? really? at 250khz? a plain old standard 1n4007? i suspect someones doing a bit of cheating regards their little demonstrations versus what they actually "made". there is a reason most of my time on YT is now spent simply reporting all these clickbait scam channels with DIY "instructional" BS videos.

[@ebbeweber1310]

Den siste idioten är inte född än...

[@ClayMole]

Hey man, is there a video you can recommend that teaches a bit about the theory and actual construction of this? @@paradiselost9946

[@prashanthubli2110]

kindly provide the green choke details or where can i find one

[@cansezgin2396]

Bu devre kullanılabilecek bir devredir. Evet DC gerilimden dolayı 2kW olması imkansız, ancak bu devreye olduğu gibi 110-220 VDC uygulanır ve bobin de su ile soğutulursa 2 kW rahat verir. 1N4007 olmaz diyenlerede şunu söyleyeceğim diodun hızından dolayı MOSFET ler rahat çalışabiliyor. Aksi taktirde miller bölgesine girer girmez mosfet kapanacak ve bir kaç MHz de çalışmaya çalışıp patlayacaktır. Sevgiler saygılar.

[@aboyosefsy4655]

عمل رائع وجميل هل يمكن ايضاً استخدامها كطباخ تحريضي باستبدالها بملف سخان تحريضي. وشكراً لك

[@ZAFERYILDIZ52]

نعم يمكنك استخدامها

[@alializadeh8195]

مرسی

[@GalindoQuintanilla]

Hola buenas tardes, tenía una pequeña consulta, los cables de color azul y los que saca del centro del Mosfet, que numero de cable son? Se los agradecería muchísimo 🙏

[@mrhkexperiment]

Good

[@iitrevor]

Güç kaynağı yapımı gelsinnn❤

[@ZAFERYILDIZ52]

👌

[@akhtarnadeem621]

Can you touch this copper coil, does it have current, is it dangerous?

[@RsBGroups]

Thanks

[@ToyMarston]

RV compressor free absorption refrigeration heat source ?

[@soorenakhan]

12 volts, how many amps?

[@ДругДружище-ж6й]

Отличная работа друг!

[@EmmetPhD]

2 кВт на 12 вольтах - примерно 200 Ампер. Забавно посмотреть на бедолагу, у которого все эти сопли расползутся в руках после нескольких минут работы 🤣 UPD - Я понял! Этот тип прочел в даташите рабочие параметры транзисторов и решил, что его подпихуйка разовьет именно эту мощность! Куплю на лето шины от Порша. У меня бибика и так шустрая, а с такими ваще полетит!

[@VINAYAK.VINAYAK.]

Super Video Sir Amazing ❤️

[@ZAFERYILDIZ52]

👉❤👈👌

[@vetaliv4696]

Як завжди - дуже ПОТУЖНО! Головне наочно і зрозуміло 👍. Маєш руки обценьки 😮, як не опік пальці, тримаючи розжарене, до червоного, лезо? 😂

[@ZAFERYILDIZ52]

Залишила поки не прогрілося :)

[@talhatopcu2254]

bobinden geçen akım nedir acaba

[@NBspark]

i am your regular viewer

[@ZAFERYILDIZ52]

Thank you for your comment and support.

[@NBspark]

@@ZAFERYILDIZ52 ❤

[@charlesbradshaw1285]

At 2kw this circuit will draw 170 amps. The device would have to be powered by a car battery. Wires and connections are nowhere big enough.

[@JoseBrasMoskow]

capacitor has 0,33uH ??????

[@Berbagicara-ku88]

Nice

[@ДругСамыйБольшой]

А блок питания 2kW для него почему не показал?

[@bogjan7]

can you explain to me where you got this 2 kilowatts from ? heat heats but 2KW from 12v power supply is about 160 A and that's without losses , those wires what you show is half a second and they will evaporate .

[@ZAFERYILDIZ52]

40N60, IGBT N-CH 600V 40A

[@samjones3106]

Its pulsed 2kW. Not continuous.

[@fuad1133]

Что произойдет на практике, если вместо двух конденсаторов будет пять?

[@ВиталийБорода-ц8ь]

Уто-нибуть подскажите: он использует диоды или стабилитроны?

[@СеваСтополь-ч4й]

в энергосберегайку загляни, найдёшь на входе детальки, схемку только не собирай, там мощи 20 киловатт, весь подъезд сожжешь)))

[@gyulagyozo]

2 KW ? this is funny...not real.

[@DanielBarrios-hp9yt]

KW?????????? 😂😂😂😂😂 kHz!!!!!!!!!!!!!

[@GILEUSB1]

Preciso um com potência pra espiral de 25cm de diâmetro

[@tonnum4143]

ทำขายไหมครับพี่อันละเท่าไหร่

[@alx643]

если нагреватель мощностью 2 кВт питается от 12 В - тогда ток должен быть 167 А - и этот ток протекает через "крокодильчики" ? ха-ха - 3 раза...

[@АлексейБессчетнов-ь2о]

Проще было бы показать схему

[@Like_av1]

IRF BE30 MOSFET ANY PROJECT PLEASE SIR

[@Валерий-ж9э9о]

Сечение обмотки нагревательного элемента значительно влияет на вашу схему!!!???

[@servetsenyl9463]

24 v ac akim trafosu indiksiyon isiticiyi calistirimi

[@JUNIOR_YT_58]

Brother ,pls make a speed counter motion sensor🥺🤔

[@New-From-Innovation-Invention]

yeah i need this

[@JUNIOR_YT_58]

@@New-From-Innovation-Invention you'er right😅

[@LuisGrabriel-v7y]

Falta información... Un tiempo considerable para una "gran película" pero no es útil. Cuánta energía requiere??? Todo está superficial -mente soldado, cuánto duran los soldaduras en puntos críticos en fallar???? Yo soy Gabriel humano en Medellín Colombia. Venga pronto tú Reino celestial señor JSS!!!!

[@sametyoldas2217]

Zafer bey hazır boyle sıstem satıyormusunuz

[@ziyaozdemir5848]

Teşekkürler Zafer bey

[@ZAFERYILDIZ52]

Ben Teşekkür Ederim Ziya Bey

[@hasantamer9199]

harika

[@adasahili51]

merhaba kondansatör sayısını arttırmanın faydası olur mu

[@ZAFERYILDIZ52]

Evet

[@TheMihrentiy]

Yes there are all three kilowatts.

[@Amerikanin2numarali_ustasi]

Sargi icine demir su borusu koyduk mu su kaynaticimiz hazir ❤

[@ZAFERYILDIZ52]

kesinlikle kardeşim

[@fewthings8917]

Wire guage of 100 uh👍

[@warrior4christ777]

. 33uf/600volt? Wow

[@starets_fugas]

Проблема не в том, как сделать двухкиловаттный индукционник, а в том, как сделать к нему блок питания.

[@Lider666sama]

Ну как вариант переделать старый сварочный полуавтомат.

[@Evgenius.]

браво

[@ylmzbas]

Eline sağlık Zafer hocam. Yabancıların yorumu bizlerden fazla üzülüyorum doğrusu. Bir sorum olacaktı bu devre için kaç watt güç kaynağı öneriyorsunuz kaç amper çekiyor?

[@ZAFERYILDIZ52]

12 volt icin 10 amper yeterli olacaktır ancak daha yüksek voltajlara da dayanacaktir

[@ylmzbas]

bu değer de kondansatör bulamıyorum da alternatif önere bilir misiniz hocam? @@ZAFERYILDIZ52

[@harunkask7448]

2000 watt ??? 12voltta bu akıma dayanacak parça yok şemada

[@tahaberber890]

Ben bu devreyi irf3205 ile yaptım calismadi neden olabilir

[@DGS.beklegeliyom]

irf ile yapmışsın işte

[@iosifszilagyi3118]

2kw means two kiwi's? In electronics, I prefer bananas

[@pritikanadas3140]

12 v how much amp power supply we need

[@ZAFERYILDIZ52]

8 amps and above are sufficient

[@samjones3106]

@@ZAFERYILDIZ52 Thats only 96 Watts. So its being pulsed 2kW. Not continuous. Theoretically you could also make pulsed 100kW. misleading title.

[@ajatsingle1703]

बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट । पूरा का पूरा बकवास कर रहा है । उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा

[@soorenakhan]

۱۲ ولت چند آمپر؟

[@_Fantom_.]

Классная штука.. А какими биполярными советскими транзисторами можно заменить оригинал?

[@Lider666sama]

Он тебе не поможет, он из Турции. Аналоги ищи по даташитам.

[@starets_fugas]

Нужны полевые транзюки, биполярные увы, не в теме. И да, ищи по даташитам.

[@denisivanov2263]

Что-то непонятно чем он запитал эту схему

[@EmmetPhD]

КТ315, естественно.

[@eduardnedoros5054]

@@EmmetPhD мп37 но лучше на мп42 они мощнее но на них надо 2 кроны .

[@МельниковВалерий-у8п]

Ничего не понял, но жутко интересно

[@emretosun3977]

frekans çok yüksek. daha fazla kapasitör ekleyerek frekansı 50khz yapabilirsiniz. benzer bi çalışmayı 20 adet kapasitörle yaptım 48khz de çalışıyor.

[@ZAFERYILDIZ52]

evet daha çok minimum maaliyet üzeriden devreyi tamamlamayı düşündüm daha çok geliştirmek mümkün minimum parça maks performans

[@maquinaseartesanatos1090]

trabalho com tubos de p.v.c e tenho que aquece-los tem alguma sugestão ? corto o cano em chapas

[@gilbertofaggioni1536]

Zafer ,tu estas de brincadeira....Gosador...

[@denisivanov2263]

Питание от чего?

[@ĐứcNguyễn-z6l3b]

2000w :12=166a

[@asangamendis6105]

Hi Thanks , Can we use this as a water heater coil ?? if so describe how it can be done plz 🤔

[@ajatsingle1703]

बकवास कर रहा है । गलत प्रचार कर रहा है । कैसे आएंगे 166 एम्पियर करेंट । पूरा का पूरा बकवास कर रहा है । उम्मिद नहीं थी इससे, ऐसा गलत दिखायेगा

[@ajatsingle1703]

False. Totally false. How and from where you are drawing 166 Amp current ? Have you any reply. So stop showing such false sense.

[@ajatsingle1703]

False. Totally false. How and from where you are drawing 166 Amp current ? Have you any reply. So stop showing such false sense.

[@superdave1921]

@@ajatsingle1703 Why don’t you cut the criticism and move along to a subject you are able to understand. You sure know how to throw a wet towel on a great project. Move along little boy…..

[@snubberless]

100-200W are real, think about that tiny heatsink with a 2kW source LOOL

[@mohssensalim2449]

Greetings to you for these new ideas. Can you make a heater to remove and solder the refrigerator compressor filter? Thank you very much. I am from Egypt.

[@tpusing]

Terimakasih

[@khalefaziz2295]

رائع...

[@ZAFERYILDIZ52]

شكرا لتعليقك ودعمك.

[@arjunsingh89626]

❤

[@omarslameh431]

هل هاذا يعمل ك طباخ طعام ارجاء رد وشكرآ 💙💙💙👍وكيف

[@amero2407]

MERCI!!

[@ZAFERYILDIZ52]

👉❤👈👌

[@ВладимирКозак-ъ1м]

Это не пвйка а мазонье соплями .

[@malibokhar5238]

❤❤❤Ok

[@erentoker4011]

hocam kablo çapı 1.5 değil 1.35

[@yasarozler921]

harika . 2kw neyi ifade ediyor. cektigi akim farkli ise

[@ZAFERYILDIZ52]

40N60, IGBT N-CH 600V 40A

[@samiyesayg]

Çokgüzel bir devre eline sağlık👍👍

[@ZAFERYILDIZ52]

güzel yorumun ve desteğin için ben teşekkür ederim

[@samiyesayg]

Sağol abi😊

[@johnpages4627]

@@ZAFERYILDIZ52 je réponds ou trouve t ont le papier jaune que l'ont peut voir dans votre vidéo en vous remerciant !