Unlock the Potential of Your Old Hard Drives: Build a Drone Engine!

Рет қаралды 2,211,114

Күн бұрын

Пікірлер: 506

@lostworld-2024-m5m 11 ай бұрын

I saw a fan turning at 7,000 RPM and not any DRONE to show it capacity to act as so. The cooling fan has no aerodynamic profile , may be you should test it with a Drone propeller to show if it can lift a battery and all the stuffs together . Does that motor has enough torque to turn a real propeller at 7,000 RPM ?

@swyntopia 10 ай бұрын

It depends on the airscrew !

@Ihavetruth22 5 ай бұрын

youtube has died. foreigners have RUINED IT. GOOGLE has ruined it. SPAM and FAKE vids everywhere. No monitors at all.

@josuestuardoreyesestrada1134 7 ай бұрын

Podrías indicar que componentes usaste para hacer pasar energía al motor estoy interesado en comprarlos, por favor

@nizarkailani6463 10 ай бұрын

If you cut off the sides on the motor body you may have much better weight , also they make 15000 rpm hard drives, i think that would create great lift

@Biliyorumfan 10 сағат бұрын

Joined 4ra’s VIP club, the perks are just unbeatable! 💎👑

@chrislong3938 8 ай бұрын

The magnets for the actuator are neodymium! Fun to play with!

@franckzippo 4 ай бұрын

how to separate magnets from their support they are glued on ? without damaging them ?

@chrislong3938 4 ай бұрын

@@franckzippo I've never found it to be very easy. I used to just pry, the magnet or bend the plate in the hope that they'd come apart. I have lots of drives to fool around with but haven't tried in a very long time. I've even had magnets 'explode' on me where they just come apart into a mass. There might be good videos out here that have good ideas! If you can find really old 5.25" Seagate drives with linear actuators from about 1985 or so, they have enormous magnets in them compared to what can be found in newer drives from about 1990 on.

@AdamJensenReal 3 ай бұрын

@@franckzippo magnets are not glues they are very strong and break easily

@franckzippo 3 ай бұрын

@@AdamJensenReal if this is true then we could be able to translate it on its support (less resistance) to separate the magnet from it (instead of trying to pull them).

@Kabsbub Ай бұрын

@@franckzippo try a solvent like acetone

@whiteNinjayt007 10 сағат бұрын

4ra's loyalty program is just too good, racking up points like a pro 🏅💎

@soosaisteven3984 10 ай бұрын

Anyone who do this, pls wear eye protection. You don't know if your old pc fan blade will able to handle extreme high rpm. It can leave you blind and bloody.

@CASSIAJohn_One Ай бұрын

C'est vidéos là, j'adore ! J'aime démonter tous les vieux appareils qui ne fonctionnent plus, pour récupérer leurs mécanique. C'est prodigieux ce que l'on peut trouver dans ces machines et leurs technologies. merci l'ami, on se ressembles. Je vais m'acheter ta deviseuse, elle est géniale ! et ta pince pour récupérer les vises. Waouh 🤩 🤩

@serjao5437 10 ай бұрын

Dica legal, tenho varios HD's antigos, vou fazer experimentos.

@gara737 7 ай бұрын

now that's a cool little project for a turbo pc cooling. thanks🎉

@osxanyin 7 ай бұрын

Too much noise

@leflamantrosefpv1725 10 ай бұрын

dream dream dream.. make the drone!

@BrotherHobby-7 4 ай бұрын

We can help you fulfill your dreams because we are a manufacturer of brushless motors, ESCs, and electronic controls!

@frwy1 Ай бұрын

@@BrotherHobby-7 so you know the Kv of this engine and its weight is NOT compatible for drone use. isn't it ?

@consentofthegoverned5145 10 ай бұрын

Those cpu fans are not meant to spin that high RPM and could shatter causing injury.

@PerilousPaddy 10 ай бұрын

Not to mention that it wasn't even close to being balanced lol

@gunaratna123 11 ай бұрын

I like your short and useful videos always. Thank you. I have a problem about brushless motors. We can find out such motors easily but it is difficult to find circuit diagrams for brushless drivers. I could not find such a one from your videos also. could you please publish such a circuit? And, can we get a higher speed from stepper motor also? Can you publish stepper motor driver also? Thank you.

@amaury1961 11 ай бұрын

Eres un ignorante, los motores paso a paso, no fueron diseñados para velocidad 😅😅😅😅😅😅

@franklydude 10 ай бұрын

100's og brushless motor drivers for RC vehicles,!! 100's Aliexpress, Banggood, ebay etc... 1-2ms input from RC channel...

@SemourKlitz 5 ай бұрын

You say drone engine, while I see a very powerful yet super compact fan for cooling things down in tight confines.

@VidarrKerr 4 ай бұрын

I see a complete waste of time and waste of additional electronics.

@monneratrj 3 ай бұрын

Exactly... i guess they are quite heavy to be on drones to be honest... best to have an awesome fan hehehe

@zumeria177 Ай бұрын

@@VidarrKerr LOL this motor power is very weak and the propeller is not suitable for RC aircraft by any means.

@DouglasSantos-ee3hh 29 күн бұрын

@@zumeria177 Why? I need to know.

@zumeria177 29 күн бұрын

@@DouglasSantos-ee3hh go back to your favela and then to school.. cheers

@BrenocaaS2k 10 сағат бұрын

Love how 4ra adapts to any device, betting on my tablet is just as easy as on my laptop 💻📱

@rokag3332 10 ай бұрын

those disks make perfect reflector laser for experiment in optic and you also have very strong magnets

@chrislong3938 8 ай бұрын

They also make great wind chimes or the backing for a cool analog homemade clock!

@luizfernandolessa1889 11 ай бұрын

Esse motor é muito bom e silencioso. Sugiro colocar outro tipo de hélice que seja mais silenciosa e, se possível, com tua engenhosidade, fazer um pequeno ventilador oscilante. Bom ano novo.🇧🇷👍🏽

@ZAFERYILDIZ52 11 ай бұрын

Eu não tinha outra ventoinha em mãos, você pode usar esse motor com tensão de até 100 volts, mas a ventoinha que eu tinha não aguentava essas velocidades, então não forcei.

@luizfernandolessa1889 11 ай бұрын

@@ZAFERYILDIZ52 Agradecido.

@tuir52 10 ай бұрын

Falou gaúcho...kkkk.

@luizfernandolessa1889 10 ай бұрын

@@tuir52 Não sou gaúcho, mas gosto da maioria das coisas do RS. Inclusive assisto um canal de eletrônica de lá. Abraço.

@smecherusmecheruu1688 10 ай бұрын

DRONE WHEN ? you are a fake @@ZAFERYILDIZ52

@gabrielayazo6908 10 сағат бұрын

4RA's detailed stats and analytics make betting decisions so much easier 📊🧠

@ezequielcastellon7059 5 ай бұрын

Hola muy bueno Pero que controlador le pusiste para que ande a 12v?????

@chakkravancoomecrong2099 Ай бұрын

ฉันก็เอามาทำเป็นพัดลมเป่าเหมือนกัน ใช้ได้ดีลมแรงเย็นสบาย😮

@mauriciohuerta7925 Ай бұрын

A que voltaje obtuvo esas rpm? Gracias por el video!🎉🎉🎉

@andrievbastichy8551 9 ай бұрын

what is the electric screwdriver name/brand etc.. any links? for the rest of the equipment too.. thanks

@stuarthelliwell6784 6 ай бұрын

Hope you were wearing safety specs,,, because those fans aren't supposed to spin so fast and you're lucky it didn't burst at full speed either that or when you turn the power up full it could very easily twist itself up in the wires/ catch on one and bounce back into your fingers taking a chunk out of them,,, basically a pointless video as the brushleess motor's for drones are much more compact,use less power "not 12v" per corner and wouldn't need you to power a drone with the equivalent of a car battery that would run out of steam in a few minutes,, the whole idea of drones is keep the weight to a minimum even the wires needed to feed power to each corner without overheating and melting would add extra unnecessary weight 🤔

@yucekaya1622 4 ай бұрын

Correct determinations, 7800 rpm means 650 kv. As a drone engine, it's ridiculous. Better let the gimbal do it

@joseairton5300 Ай бұрын

Eu adoro a tecnologia e esse tipo de motor eu tenho uns três guardados só esperando uma oportunidade de fazer alguma experiência

@adrianwhitefang7615 11 ай бұрын

Thanks for this video. Can you make a video with the ESC that you used here?

@sinanyc.2105 11 ай бұрын

Emeklerine sağlık ustam hdd motorlari ağır oluyor uçuş icin pek kullanışlı degil ama soğutma ısıtma islerinde yada birazda tork saglana bilirse rc araclarda 10 numara iş yapar tabi benim kendi fikrim usta artik bu motorla bir proje yaparsın inşallah selametle ustam simdiden hayırlı cumalar selamlar 🤲👍❤️

@odszczepciesie5128 11 ай бұрын

Nie znam się na tym, ale chodzi mi po głowie, żeby wykorzystać taki silnik w turbinie wiatrowej do generowania prądu

@sinanyc.2105 11 ай бұрын

Evet olabilir😊👍 guzefikir l@@odszczepciesie5128

@tunamadanoglu 7 ай бұрын

Emeğinize sağlık. Öylesine akışta denk geldi baktım. Enteresan şekilde yabancılar daha çok yorum yapıp teşekkür etmiş. Bu neyin göstergesi acaba 🙂 Genel olarak okumuyoruz, araştırma yapmıyoruz, bunun gibi DIY projelerle pek ilgilenmiyoruz sanırım. Belki de günlük kaygılardan fırsatı olmuyor insanların. Emin olamadım.

@ugetridofit 4 ай бұрын

Just because you have RPM does NOT mean you have the torque to spin a prop.

@ferocious_r 3 ай бұрын

These spin solid steel platters

@bigdeelearning6406 2 күн бұрын

Thank you I know it can be done ❤

@gorakhdesai 10 сағат бұрын

Those daily challenges on 4ra keep things spicy, love the extra thrill! 🌶️🎯

@zedium 8 ай бұрын

Does it have much power to pull up 4 motors and other stuffs such as battery used in drone?

@RixtronixLAB 2 ай бұрын

Creative video ,thanks :)

@georgeh9967 11 ай бұрын

did not look like it had the power to lift itself, even without a battery

@DavidSmith-dm8ew 11 ай бұрын

nice fan but... useless for rc!

@Bueno336 11 ай бұрын

É lógico que não 😂

@Oficina2tempos 10 ай бұрын

A hélice e mais pesada que o motor e tem muito pouco arrasto para o seu peso

@IMETMIRANDAM 10 ай бұрын

La solución está en el diseño de las hélices

@3dChris Ай бұрын

The fan blades are not idea for this kind of mod.

@AdamJensenReal 3 ай бұрын

How you control the motor can you give us a schematic or how it is named and where to buy any detail will be helpful. Also you can make from this little cutting machine or sanding/brushing, or for sharpening of blades.

@niteowl4961 Ай бұрын

I found both on eBay for 5 bucks US. 30a 12v dc 3-phase high-power brushless motor speed regulator

@williamrowe8545 8 ай бұрын

What speed adjusting product did you use to attach to the simonk30A ESC to control motor speed?

@ogpennywise 5 ай бұрын

Rheostat, potentiometer, variable resistor.

@niteowl4961 Ай бұрын

Actually it is a - CCPM service consistency master. I found both on eBay for 5 bucks US. 30a 12v dc 3-phase high-power brushless motor speed regulator

@ChrisWatkins-k5b Ай бұрын

Hey, does it matter how you hook up the blue wires? Is there a certain order?

@GM72COL 9 ай бұрын

Serviría como ventilador pero como motor para un dron lo dudo mucho. Los motores de los drones pueden girar entre 10.350 y 41.000 revoluciones por minuto (RPM).

@JoaoReis-yn5hn Ай бұрын

Não pelas rotações mas pelas hélices.As hélices de drones são como de helicóptero,em formatos de asas.

@TheOnlyonejeep 9 ай бұрын

that looks cool...what is under the heat shrink how is it wired to motor? that is puzzling

@PrinzKenny1 9 ай бұрын

Under the heatshrink is an ESC. Since hard drive motors are BLDC motors, they have 3 phases whereas each phase is connected to a pair (or multiple) of coils inside the motor. Normal DC motors just require + and - and they run. For BLDC motors it's different because you need to turn on and off the coils in a specific order and at the right time. That's what the ESC does. A simple ESC contains 6 mosfets to be able to spin the motor forward and reverse (some might only have 3 mosfets, which would result in only forward motion. You can take a look at full H bridge or half H bridge if you want to take a deeper look). Besides the mosfets there's also an IC which does all the calculations for controlling the three phases according to the input signal from the potentiometer. There's way more to it, but I hope this helps for a brief understanding of what's going on :)

@frandei4416 11 ай бұрын

Soy nuevo y novato en la electronico pero esto es fascinante una prueba del ingenio humano me recuerda al maestro humberto higinio ser posible en un futuro un tutorial de un dron casero? Seria fascinante❤❤

@Royer_-qd4bn 10 ай бұрын

Humberto Higinio, un crack, de dónde eres?

@frandei4416 10 ай бұрын

@@Royer_-qd4bn soy de panama

@FatihEgemen-hp8ck 11 ай бұрын

Mrb zafer bey elinize sağlık... Benim merak ettiğim şu ki; bu motorlar ne kadar güçlü dron değilde acemice bi çim biçme makinasına çevirsem yani gerekli uzatma malzemeleri ile ucuna bu motor u baglasam cd gibi cıkardıgınızın parça yerine 2 3 mm lik plastik sıkıştırsam iş yaparmı sizce...

@hakgg2874 11 ай бұрын

çim biçme ihtiyacınızı karşılacak kadar güçlü değildir

@FatihEgemen-hp8ck 11 ай бұрын

@@hakgg2874 teşekkür

@joseairton5300 Ай бұрын

Me diga onde comprar um esque e como comprar eu escolher eles funcionam até com quantos voutes

@gaudibursch279 8 ай бұрын

Super!

@Tomboy_girl-py8fi 10 сағат бұрын

4ra’s interface feels like a pro tool but easy enough for newbies too 💼👶

@alptravm 9 ай бұрын

kontrol arabirimi olarak kullandığınız komponentin marka ve modelini gibi bilgilerini ve bağlantı sırasında lehimlediğiniz uçların ne olduğu ve nereye bağlandığını da açıklasanız güzel bir eğitim olurdu lakin bu şekilde sizin kişisel şovunuz gibi duruyor. güzel bir kanalınız var öğrenci gençler ve elektronik meraklıları için daha eğitici olmasını dilerim.

@GigglingGobby 4 ай бұрын

Lots of revs, but it barely seems to be able to lift itself off the desk never mind a chassis and power supply and control gear and a camera and a parcel delivery basket etc 😁 need to see the finished drone!

@Dancopymus 3 ай бұрын

Legal mas, seria melhor fixar bem a hélice do Fan no motor do HD, até para segurança pessoal.

@gp37521 8 ай бұрын

Now if only i had 4 hard drives sitting around, instead of a few $ to buy real ones!

@PFinkoloTL87 9 ай бұрын

When did they start to make the hard drives with brushless motors?

@gokhanozcan5065 2 ай бұрын

Merhabalar Zafer bey kullandığınız sürücü ve hız kontrol devresi için model ismi veya link verebilirmisiniz. teşekkür ederim

@ben4518 2 ай бұрын

Dam good idea, a drone with wires attached, then turn the motor full power to burn it out.Just one though just how much spare cable do u have before it goes 50ft? if it dont fly... what is the point of making it. A hard drive is not ment to fly... or is it?

@jazzed892 5 ай бұрын

ZAFER HOCAM BEN BU MOTORA 5V DEYDİRİP CEKTİM BOBİNLERE ZARARİ OLURMU

@inhuitathlvacir7245 6 ай бұрын

the motor is powerful it's true I have already tested it for other functionalities but to say for a drone it is not necessary to have a motor there is a whole technology behind it

@augustov8mustang503 4 ай бұрын

É nescessário tambem rpm suficiente para realizar o trabalho com a hélice, se tiver muito torque e pouco rpm não vai ter empuxo😊

@LuisCarlos-ej8dc 2 ай бұрын

Ola boa tarde amigo onde compro esse regulador de velocidade Obrigado

@RampageSvGAMING 6 ай бұрын

Drone propeller should be used for lifting, that its a fan

@cetintori 9 ай бұрын

Está tentando reenventar a roda, existem os motores sem escovas bruschless que seriam mais potentes e mais leves!

@6pack1204 10 ай бұрын

Did I miss the video where you made 4 of them and mounted them on a drone and flew away?

@criandoEdesenvolvendo 6 ай бұрын

What does ESC stand for ? By the way, great video. Thanks

@jesusrubio4948 8 ай бұрын

Me gustaría saber qué es el aparato que le suelda y cómo conseguirlo me gustaría saber cómo se llaman los componentes para poder comprarlo por separado y montarlo gracias

@matejs2638 10 ай бұрын

Der Motor ist für eine Drohne VIEL ZU SCHWER UND VIEL ZU SCHWACH... Es geht nicht nur um Drehzahl, sondern auch noch um Kraft... Der Motor fliegt nirgendwo hin außer wie im Video am Kabel hängend... Der Tipp ist also leider völlig sinnlos für diesen Einsatzzweck...

@enginkusak7095 10 ай бұрын

Bu disklerin motorları 12V. ile çalışmıyor mu? 12 Volt ise amatör drone motorlu olmaz kanısındayım.

@joseairton5300 Ай бұрын

O que mais me deixa irritado é que aparece tal projeto mais quando a eu vou começar não encontro as peças

@Север-о9ы 9 ай бұрын

Гарний стабілізатор для маленького гелікоптера.

@IronAmibo 4 ай бұрын

What kind of esc to use with 10 or 15k 12v and 1500mA?

@diddd4970 7 ай бұрын

The magnets are also interresting!

@joseairton5300 Ай бұрын

Um abraço meu amigo e que belos vídeos

@ZAFERYILDIZ52 Ай бұрын

Obrigado meu amigo!

@DIY_ideas8219 8 ай бұрын

great video thank for share

@DJ.Anushka 4 ай бұрын

your video is good but can't make drone this bldc motor because no thrust to lift

@betopx2 11 ай бұрын

The circuit that controls the motor is missing. Is there a simple circuit that does this?

@egehanzekeriyadundaroglu2182 11 ай бұрын

4 eski harddisk ile birlikte beklediğimiz o video

@ZAFERYILDIZ52 11 ай бұрын

👌

@milhistorical2238 5 ай бұрын

4 harddiski çöpe at gitsin, o teneke kendi ağırlığını kaldırmak için falcon 9 roketinin itme gücüne muhtaç, Millet yorumlarda kıçıyla gülmüş zaten video başlığına

@SergioTavares-ii1yf 6 ай бұрын

Thanks for sharing you knowledge.

@luciebloem9150 9 ай бұрын

Il est où le drone ??? Faut continuer car là y a seulement un millième du travail de fait et je suis gentil ...Vous avez fait un petit ventilateur c'est tout !

@angelriveros8095 5 ай бұрын

Seria tambien muy util como ventilador para enfriar por dentro un pc de escritorio.saludos

@iFound99 8 ай бұрын

Great ❤

@dcy665 4 ай бұрын

Interesting, where is the version from the thumbnail? That is why I came here. These are fun, but pretty clunky for a modern drone.

@comptegoogle3262 3 ай бұрын

Diamondmax plus maxtors have integrated motors - no need to dismantle them - you can just throw them away.

@gordonfinn7504 3 ай бұрын

I will make this, instead of the reflector, try sticking a red, blue, and green patc😢hes on the blades. In theory it should create a white streak.

@juancarlossanchez118 11 ай бұрын

Muy buen experimento sobre cómo reutilizar ese estupendo motor.

@f_inalerd_oppelsto1587 5 ай бұрын

wie heißt das blaue Kästchen mit dem gelben drehknopf? und wo bekomme ich das?

@gamecuber6 10 ай бұрын

to the the people who are actually planning to do this: PLEASE, if the hard disk you are gonna be using for this can still store data correctly and has no issue you are better off using it as a backup drive, but if it doesn't work (for example it clicks and doesnt get recognized by the computer), then this project is an awesome idea!

@machmichmuch 10 ай бұрын

Interesting how you remove every single screw

@joseairton5300 Ай бұрын

Por exemplo: ten um vídeo de um tal fogão de indução que meu irmão já desisti eu acho que se ele vendesse os componentes erra bem melhor

@samizgaibi5474 8 ай бұрын

ماهي الدارة التي تشبك مع المحرك وتتحكم فيه انا جربت 12v DC ولم تعمل كما يجب

@fepelixpi 10 ай бұрын

No puedes pasar enlace de lo que conectas antes de oa batería? O explicar como lo haces

@ve2zzz Ай бұрын

0:44 ...Oops... forgot to remove the head actuator pivot screw.... 1:00 Try not to touch the disk platters with your bare hands... 1:29 To not forget the bottom head actuator pivot screw...

@mustafatomen8299 11 ай бұрын

Hocam merhaba. Harddisk motorunu direk 12v vererek calistirmak mümkün mü?

@o.fluoglu 11 ай бұрын

hayır motor sürücü şart

@andraestece 4 ай бұрын

wah keren nih infonya, mantap jaya kakak.... salam sukses sama2 kakak 👍👍👍👍👍

@djmskywalker6459 8 ай бұрын

Cool

@pandainformatica8963 10 ай бұрын

Olha existem hds com 7200 rpm como esse ai e 5400 rpm e os scsi de 30000 rpm faça o mesmo teste com um hd scsi de 30k rpm ou um sas de 30k rpm... 🤔

@robcat7499 10 ай бұрын

Was hoping for lift off with that strip of electrical tape. That would have been an affordable propeller for a drone.

@zippy777l 11 ай бұрын

Unfortunately there is an awful lot missed out on this. I just spotted that another screw had to be extracted from the cover to enable it to be taken off, which is under the information sheet at the back, and which has to be exposed by stripping off a small piece of the sheet. Again, we aren't informed what the orange controller does, or how to get hold of a suitable one. If you're in the know, bully for you. And although I accept that the computer fan was put on merely to make the point, it would have been much more useful to have a proper propeller, and to have some indication of the lift ability. Fan speed doesn't hack it here. And the motor weight? You have to be kidding. This sort of clip is much more to the point if the old drive is used for some sort of small sanding or grinding tool. But not a drone, no way.

@donalain69 10 ай бұрын

Along with the disk, it makes an excellent gyroscope...

@dc6233 10 ай бұрын

Look at a Dremel itself, which has a dedicated motor to being a sanding and grinding tool and 120V. It has no torque whatsoever and is very easy to stall. I doubt a disc drive would have even a fraction of the torque that a typical rotary tool does. Curious to see if he actually tries to build a drone with this motor or by using 4 of them??

@CnRSPACE 8 ай бұрын

Plenty of people have used these to make working drones. The orange controller is an ESC electronic speed controller for RC model motors. The dial he uses is a PWM to control the ESC. Also the only two most important factors in RC model drones is RPM of the motor and its weight other than input values. Thrust is calculated from RPM + propeller characteristics so in terms of making a drone the only other important factor is motor weight.