How To: Fixing a Saggy Car Door (Third Gen Camaro)

[@robkaupp5027]

Very helpful video. My door is not as bad as yours (91 Z28) but would like to fix it before it gets worse and watching you do this gives me confidence that for under $20, it can be done.

[@JRBird]

Great job! I just did that on a 4th gen. So nice to be able to click your door shut!

[@bmead144]

The reason the bushings fit so loosely in the top hinge is because once the pins wore past the original bushings- the pins ride in the holes in the hinge and waller the holes out and the new bushings no longer have a round concentric hole in the hinge to seat in- should have never let'em get that bad!

[@locotrucker46]

Excellent video my friend. Very helpful. Much appreciated.

[@REVIVAL753]

Great content. Maybe now I can fix my sagging doors😊

[@kitt28]

that was a good video, sorry to see that alot of your door hinge parts was missing, my car saga to, i have to keep shuting my door really hard, im sure i would stil have to slam it hard after my sag repair, but this video did help me understand how to go about my repair.

[@anthonyhart6723]

Check where your door latch is in the door jam it may need to be adjusted too, it looked like it may have been making contact before the door actually caught the pin.

[@LuisAFigueroa]

Thank you for this video tutorial! I will be doing the sagging door of my 92 RS soon and this will be very helpful.

[@raymondscroggins69]

About to do this on my 4th gen Camaro. Should probably check the GTA also 😅

[@ThatNastyZ28]

Did it fix that gap between the door and the fender? I have the same issue with my z28 and wanna know if that did the trick

[@rueben44]

Thanks for the video but why would you install the second pin off camera? It defeats the purpose of us seeing the install. Also you needed to adjust those hinges to the highest point because your door was lifting as you closed it. If it stays like that you are going to wear out the pins you just installed.

[@harryjones2420]

I left the fender on

[@dragoonTT]

Was it easy to remove the door with the fender still on?

[@harryjones2420]

@@dragoonTT I only needed help holding the door against the body til I got the bolts started.. The rest was not bad at all

[@zachpappas9685]

You engine looks GREAT

[@harryjones2420]

a little red grease would help keep them from wearing out

[@angelgovea9840]

Great job helps a lot

[@sethllly]

i like your style

[@xNightflyerx]

Great vid!

[@petedegreat1697]

I dont that without taking the door off the car... very easy . !!! all you need is a floor jack to level the door. then you will need a machine like the one he have... you will need to buy a new blade is like 8 dollars you will need 2... one for the top bolt and one for the bottom one... once the the door is level cut the top bolt off with the machine . once you get that sucker cut off, you will need to drill it out from the top ... you will need to buy a long drill bit at least a 10 inch one... now after the bolt is out. remove the floor jack let the door hanging in order to put the copper ring. level the door again to put the new bolt ... I promised you all camaro lovers that door will open and close like it dit at the show room... in fact you dont need to do the other one but I did it anyways ... the bottom bolt will need to be drill out from bottom ...

[@petedegreat1697]

I did it my way because I dont want to take my car to the body shop to adjust the hood fender and the door... also if you need to take the door off is not need to remove the fender...!!!

[@cfmechanic]

Maybe better title would be 3rd gen gets door lift lol

[@ZanesGarage]

That would be more accurate lol i couldn't believe how mangled the brackets were once I had it off

[@betilloparra855]

👍👍👌

[@johna.4334]

Crank windows? Eeeeek!

[@jeremybennett5547]

Crank windows are king

[@locotrucker46]

Yours is a little worse than my 86 Z28