ZWQ S100s Baize Basic Upgrades!

[@BradleyPhillipsYT]

Since recording this I have ordered two custom springs to suit this blaster. Stay tuned to see my final results in my full review video. Spring dimensions are 1.8mm x 17mm x 300mm and a stronger 2.0mm x 17mm x 300mm. Find it at the below links: OutOfDarts (USA): outofdarts.com/products/zwq-s100s-baize-blaster?ref=RIa3bVI3vXYhUs Blastertech (Australia) www.blastertech.com.au/S100S_Baize_ZWQ_BLASTER/p2928293_21987134.aspx Frontline Foam (USA) www.frontlinefoam.com/product/baize-s100s/?sld=8

[@lyonel4044]

That's the video im looking for.

[@godeatsbagels]

I just purchased the 1.8 spring from frontline, but they don’t carry the 2.0 one. Any idea where I could get that spring? The 2.0 spring for the s100War Saint doesn’t fit sadly. I’m trying to make this my highest performance blaster.

[@BradleyPhillipsYT]

​@@godeatsbagels I went on eBay and found someone that sells 300mm springs of all sizes and it lets you choose the diameter and gauge.

[@arifickel2077]

​@@BradleyPhillipsYT could you please drop a link to the ebay store for the springs?

[@yehnahthx]

It may seem counterintuitive, however when double sealing its preferable for the piston ring / rubber o-ring on the low pressure side to be a slightly less efficient seal than the high pressure side. It significantly reduces wear on piston rings.

[@syarizansulaiman6554]

I'm usually use hair rubber on plunger before put O ring, there is two places can put it, that my secret on my blaster. Just try can fit or not first 😊

[@FrontlineFoamBlasters]

Spring spacers! Glad you tested with the 1.7 spring. We also have 1.8 on the way and are excited to try it. I used Woker Swift/Harrier springs and was hitting 300 with the 1.6x300, but that gets more compression it seems like.

[@BradleyPhillipsYT]

The stock springs have somewhere around 2 inches of slack to them. It's ridiculous.

[@arifickel2077]

The worker springs work in the Baize?

[@FrontlineFoamBlasters]

@@arifickel2077 the springs are narrower, so just some slight modification to the width of the plunger spring guide and a guide in the back to keep the spring aligned and it can

[@dangermaus9253]

Circlip pliers can sometimes let you replace pusher o-rings via the magwell. Depends on the blaster and the pliers you have.

[@BradleyPhillipsYT]

Yeah I don't have a pair of those, but I found a different way using the scribe tool and a ram rod down the front of the blaster the same diameter as the pusher.

[@Antmac75]

Gday mate on one frontline’s vids he says it comes with a 24” barrel. You can see the barrel poking out the end of the plastic shroud thing. Like yours my barrel in much shorter. Maybe an aussie thing? Now I’m waiting for springs as well , also fitted a 550mm barrel. Love your work👍

[@BradleyPhillipsYT]

I've ordered a Worker 550mm barrel for mine. Should help bump up the performance!

[@TheTeepane]

Hey Bradley I was just wondering where you got the box of O-rings from I'm having some issues with my seals on my Nexus Pro was hoping you can help me out

[@FoamworkAdelaide]

Orings, don't we love a set that can buy to solve all your fitting problems. The red, the green and the black. Or ending up like me who have five different sets 😂

[@liangjun24]

Hi Bradley, I'm Andy from sg. I have a couple of questions. Do u need metal internals like plunger rod and stuffs for this S100? Is the prime exclusively on the right? Can we prime on the left? I'm interested in this blaster but would like to seek your opinions before committing.

[@justinmorris2199]

Heyo! I just purchased one of these from frontline foam and got the latest version. To answer your questions, the bolt comes with handles on either side and is ambi prime. I personally don't find the metal internals kit necessary but the FPS out of the box is where I need it to be

[@MonteQuigleyWalsh]

Hi Bradley.. I have a ZWQ S100s I get fps 157 what size replace pusher o-rings did you use on the upgrade?. any help appreciated thanks.

[@snailxixi]

@bradley philips which one do you prefer the worker swift or the zwqs100

[@BradleyPhillipsYT]

Both are good for different reasons

[@jakedogan4875]

Hey bradley, just asking if this blaster is compatiable with swift 1.8 spring? Just concerned as the spring is almost 2 times longer than the 1.5 spring it comes with. Thanks

[@Antmac75]

They’re too long. I cut a swift 1.8 spring to 300mm and tried it. Definitely need a spring guide inside. It was crunchy without one.

[@Eulemunin]

What hardness and material are the o-rings you are using?

[@BradleyPhillipsYT]

www.ebay.com.au/itm/255513844532?mkcid=16&mkevt=1&mkrid=705-154756-20017-0&ssspo=YHtaEBwVRSe&sssrc=2349624&ssuid=4dlrwsZsT9G&var=&widget_ver=artemis&media=COPY

[@Fynn_baxter]

Nice video

[@justakid8677]

Can’t wait for you to get ur hands on a harrier…….

[@Omninfinity]

I think it got seized by customs

[@ClarenceSampang]

What were the O-Ring's diameter?

[@BradleyPhillipsYT]

The ones I used to get the 2 second seal were 7.8X1.9 according to the box. I have since tried even smaller ones and reversing the barrel instead of having the flared end and that achieved about the same, maybe slightly longer like 5 seconds.

[@ClarenceSampang]

Disassembly of the blaster seem horrendous but I guess we've been spoiled with the Nexus' and Trion's spring change feature and DZ Pro, Prime, and Harrier easy disassembly. In hindsight, the Baize disassembles like a standard Nerf blaster and with the potential for modding, it seems worth the slight inconveniences.

[@BradleyPhillipsYT]

​@@ClarenceSampang some parts are still quick to change. Spring, barrel, and I also found a trick to getting orings on without opening it either involving a ramrod the same diameter as the pusher.

[@Ggooosee]

Are you going to do gameplay?

[@BradleyPhillipsYT]

Probably, but I only have the one stock mag and no talon adaptor.

[@godeatsbagels]

@@BradleyPhillipsYT FF sells the .STL of a talon adapter now, if you've access to a 3D printer

[@Fynn_baxter]

Too many o rings 😭😭😭

[@m00k61]

Hi my name is Mr. O'Rings. Larger O'Rings.

[@Castdeath]

Very silly disassembly and springs access imho, could have been done better by ZWQ

[@BradleyPhillipsYT]

Definitely, although it's no different to how most Nerf blasters used to be a few years ago.

[@skatteredlogic]

This blaster is shit, got a better deal out the box but lost it when changing barrel n orings were no help

[@skatteredlogic]

*seal

[@BradleyPhillipsYT]

Out of the box performance is bad, this blaster has a larger plunger tube than a Caliburn though so performance should be insane if you actually mod it.

[@skatteredlogic]

By all means the potential is there n IV seen the vid of the near 500fps build with metal internals and 2mm spring, iv already gone back at it and managed to get a seal again and getting 170s again but still extremely disappointed in the blaster, hopefully we can get the metal stuff soon so the potential of these can be more easily achieved, were did u get your 1.7 spring btw

[@BradleyPhillipsYT]

​@@skatteredlogic ZWQ supplied the 1.7 but as I said in the video it doesn't provide full compression. Get your own better one.

[@dawgydawger7158]

First

[@Fynn_baxter]

First

[@BradleyPhillipsYT]

Someone beat you :P

[@Fynn_baxter]

U

[@Fynn_baxter]

Your an amazing content creator