Братан, кратеров у тебя нет на лаках axalta?

What reducer you use for the wetbed that you have time to apply base coat and don’t dry? 😮

aren't you supposed to apply this type of paint with a crosshatching type of stroke and at an angle?

Dont you let it dry between coats thats what i was told to do.

Was that 1.3 or 1.4 ?

Where can I buy this?

That last clear coat was really thick. I'm assuming you did that for buffing and sanding purpose.

que regulacion de la pistola y presion usas para tirar la base del color?

Hi mate to do a blend has the paint got to be bang on to match the car 🚗

Hi Mick, beautiful colour and a beautiful finish from the clearcoat which went on very flat and glassy, I do like the candy reds more so than the pearl 3 stage colours I think my fav is the 46V Soul Red Crystal👌 It's great to see another video from you brother as it's been a while since your last upload, love to see more when you can Mick👏🙏👍John UK

U got that walking the panel down!! Looks good, awesome job sir

Great work man👍 what clear you used this?

Like your content man although it’s hard to hear you sometimes. I sprayed spies and glasurit solvent for about 12 years. For almost 2 years I have been doing mostly body work at a shop that sprays sikkens autowave waterborne. The painter is going on vacation so I will be painting next week. I’ve sprayed here probably 10 times or so thankfully with no problems but I know I will run in to something sooner or later. If you have any tips for me on the water base I’d greatly appreciate it. Is there a wet bed I can use? Any tips on the sikkens line in general would be great to know too.

Rodriguez Sharon Rodriguez Dorothy Walker Nancy

WOW!!!! What brand of clear coat did you use. It's incredible.

This is embarrassingly slow. Go buy Axalta, I would have been clearing by the 2 minute mark.

I prefer this method it's slightly different from Axalta but it's easier and less complicated, Well done and nice finish also nice smooth transition. Hoping to see you do a 46v

What will be your best advice for a clean panel with minimal dirts ? Thank you

It was very difficult to hear your voice due to the mask and vent noise in the background. You should have did a voice over after finishing this video. I did hear you state you are going to blend? Looks like you did a total paint-over. No blending. Sorry, this video did nothing for me....

Where is your shop located?

I’m having my supersonic red Camry repainted after a deer accident. The paint the place uses is this brand. Hope it comes out ok

What clear are you using now?

Hi Mick, it's great to see another video from you as it's been a while since we saw you so welcome back👌the basecoat went on really nice with the 3300 I have heard that it's a good all round gun which I think you used for the clear as well👏thanks for sharing and I hope you can do some more videos soon🙏👍John UK

after doing 1.5 coats i noticed you do an extra drop coat after. is that just to make sure everything is orientated?

Brilliant 👏 video 📹 that whats up with your kiwami 4 1.3 do you still use it 😊

Super like from me I have a small mark on my car bonnet and I have put some primer on it will I have to use a wet bed in a small area and then base coat paint and clear coat paint

VW love ✌🏼🚗

How many coats of base are you applying?

good

How does one know how long to extend the blend coverage from the repaired substrate?

Wich clear you use

Completely slick as glass, Awesome job.

Hello, how long time do you wait between the layers?

Hi I’m new to painting, why did you swap guns for base and only used it on some areas? What’s in the other gun ?

jest jakas różnica pomiędzy 3300 gto - 3300 gto pro???

Awesome job my friend. You make it look so easy . But thanks for all the information it helps a lot

I’m just curious how many coats did you do prior to the drop coat for base coat? Thank you.

Mine has been great. I prefer it over the black widow.

Hey Bro, just curious what psi you typically use with the Slim Kombat? Also the Kiwami 1.3 for Clear??? Thanks!

1.2O for base….& 1.3 I for clear ?? do you ever use the HVLP

Hello, _roughly_ what do you think it would cost to paint a 06 Subaru STI in World Rally Blue Mica (code 02C)? Exterior only(no engine bay) I was quoted 16K by one shop but that seemed a bit high. Do you think that's correct or is there a smaller ballpark figure that would be more reasonable?

That will never match, unless you put whatever was on the fender, on the door under the silver. I have painted for 28 yrs. 3 yrs with axalta. All paint needs the same color under the basecoat on each panel.

hi why did you spray wetbed on where you spray the color? i thought wetbed is only for blend areas?

vonroc #?

I always thought it was 1 & 1/2 coat but that looks like 4 coats if not more back to back

Not a good demo at all. Your 1/4 had sealer and blend panel did not. Mistake right there. Then you wet bed the blend panel and blend the door with a 1:1 color/clear base and get color all the way to the front of the door. If that car matches when assembled. You got lucky. You are showing bad habits. Outside. The 1/4 wont match the blend panel and the blend panel won't match the front door. Unless you get lucky. I doubt the trunk or bumper will match either. You always need the correct G base formula under all new panels for Proper coverage. Even on the blend panels. Again. You may get lucky but it's bad habits and you will run into problems

I have that problem right now with Toyota sienna paint code 3q3 but it didn’t react to my solvent based sealer but it reacted every where else

Beautiful job an very well explained 💯

is that a iwata kiwami? what psi and settings do you use? Its my everyday gun for base, fricken awesome and cheap!

How much activator did you put in the base coat?