Thanks!

Hello! P1160 P1161?

This was such a quick fix, thank you so much!

Also do a PPSR on the vehicle. I was about to buy a HiAce from this Afghan guy named Mohammad here in Adelaide and he claimed to not know what the VIN number was so we paid $10 to run a PPSR using the number plate (is only $2 with the VIN) and it came up as previously being a repairable write off. Some really dodgy stuff going on out there.

thats one where is the other?

Location of imcr please? Apparently not even Google knows where it’s at

Toyota Avalons were sold in the US as well.

I changed the boot lock on my 2020 Tiguan last week. I removed the torx screws and just unclipped the panel at the bottom around the lock without removing it completely, there is no need to remove the side trims or the top one. You can then bend it enough to use a ring spanner to remove and refit the lock. It took about 20 minutes.

It's not caused by oil. It's exacerbated by oil. Mercedes got the metallurgy of the balance shaft wrong. Metal is too soft, the timing chain will grind the balance shaft sprocket teeth off no matter what. Happens at a lower mileage in the early m272s and it happens at a higher mileage in the later m272s.

How i can fix tapping noise on my hyndai i40?

How can I fix noise in my Hyundai 2.4 L

you aint no mentor = your sloppy !

Hey man can u send me you’re number so I can book in with u please

Hey mate can u send me you’re number please so I can book my car in with u

Mate my vt when i start it up first thing in the morning and i drive the car and i turn a corner mainly happens when im turning left i her this water gushing from the back of the dash on drivers side do you know if this could have ro do with heater,thanks for your help 👍

You can have these issues with any car!

I came here for help with the wires, empathy is great but I'm still lost lol!

Just did mine and replaced Gromets. When pulling it off and was not hard as old ones has oil added by Dealer, one Gromet stayed on Engine Mounts which is the wrong way. To get them off in case they stay on those mounts instead of the Cover, use a screwdriver to wedge right into the hole and simply turn and pull the rubber up.

Those 4 Rubber Gromets need replacing each 4yrs with the Air Filter. That is why it was hard to remove and likely from not doing as scheduled. There could be suction under these same as there is for the Coils.

Any idea why I have a emission garage light come on

I'm so thankful for this video, saved me so much money. Thank you for sharing, I really appreciate it. Used this for my 2018 Audi Q 5.

That's not a kuga

I don't mean to be rude and I feel like you would already know but incase you don't Diesels don't need the throttle body

Absolute shit design. I have big arms and it’s ducking hard af. Scratched my arms like crazy. I reckon it’s made for Japanese people with their tiny ass hands

useless bit of info

My koleos(qm5)is left steeringwheel.. but the difficulty is same right side....😢😢😢

I wonder some put the front ones wrong the down part of the covers are up. They have to be like the one you have in the back. The one broken someone left loose or put wrong as the front ones.

Thank you for posting this. My timing was off after water pump install and your video helped me get it right.

How did you find the bypass was at fault nay I ask ? Ty

where do you go to get these updates

Bonjour ou attaché le crochet derrière svp

Thanks for the info Just changed a battery this morning and had this happen, super frustrating

Thank you, the video was really helpful 😊

My relay keeps blowing about every 4 months! Please help!!

Bolt torque 25Nm

I have a new manifold and next runner flap sensor. I still have codes p2015 and p2006. 2015 a3

Thank you very much sir, for the video, now i know where and what type of the filter should be

Gotta do this soon

If you read the shop manual, those clips do remove to release the radiator. The manual shows to remove the condenser by removing the radiator from inside the engine bay without removing the bumper at all.

I have a suzuki sx4, changed the master cylinder and the rear two cylinders, the same problem pedal goes to the bottom

I can’t go over 65mp?

Thanks bro, leaking atf from bottom connection, good to know

Hi sir, im doing repair on a starex right now, brake issue, goes hard when idling, but OK when rev up. I done changing the booster, valve hose & this vacuum pump. But nothing changes. Still hard during idling. What could be the problem? Is it possible it caused by the clogged oil passage from cylinder into pump?

👌👌👌 thanks for the tip!

New to Audi, love it but does anyone know where to guide to with a oil leak seemingly comes from rear of engine about halfway up in the center. Im not having to put much oil into it maybe .5 quart monthly. The undercarriage is soaked

Where the fuck is the bleeding screw

where is your shop? I have the same issue, hoping you can fix it for me

I have exact same car, and it happening exactly same thing. I changed the spark plugs, coils, chackshaft sensor, oil change, throttle cleaning and engine light po302 still there and car engine is shaking as well

Will try your screwdriver hack, couldn't turn the bulb holder by hand, removing trim on engine side of top fender gives quicker access

Great job thanks !!! Do you have any pictures of the sensor installed??