I like using old scrap iron and making me think outside the box 😊 Building for the less amount as possible but as strong as possible 😮

I see alot of these people are making out of old snowmobiles. Why not fabricate some type of seat so you can sit down like on a snowmobile? That would make sense especially for long runs like across a lake for ice fishing.

That's frickin AWESOME!!!

Great job you are talented.

Sweet

Best part, no insurance!

Nice

Yo is it for sale.?

Great idea 💡

Sir....what gears are you using in the back.. an in the front.....I mean teeth wise. Please let me know...

Awesome! Put both sets of sprockets on the same side, add a tensioner. Just back off tensioner, change sprockets, tighten tensioner. Then you could have bearing inside secondary and change belts easy. Great build.

Perfect for a homeowner, most seem to be huge, bulky, overcomplicated, and seriously industrialized. This is what we need more of, doing the best with what ya have. Looks great, works grwat, not over thought or complicated, and really nice design. A few kinks to work out, but, didn't cost ya anywhere near $7,000 a low cost store bought would run ya either. For all the money ya saved, can add a nice seat, and a heated cab to run it from.

Well, here we are almost a dozen years later how would you say it held up pretty ingenious I must say .have you put an impact driver set up on it yet?✌🏻

Quit using flat black high heat BBQ paint, buy high heat engine paint from the auto parts store. You can paint them multiple colors.

Good idea. Im wondering why not make it fit onto the hinges for the tail gate?

looks like good clean fun

👍👍

Do you have drag tip on your wand? Plus is it high frequency start? Been watching some of your shovel art vids. Looks like in free hand you touch the metal. Or are you just hovering over it? Great work!

Drills set way to fast and always use oil.

Cool design. I have to use chassis ears and that finds me the source. However hooking up leads takes around an hour to do

Great idea so Great i had to build my own 😊

How much for one of you're heaters

So, did this thing work? Has you used it successfully to find noises in suspension?

Legs look crapped

Angle the back cross support the other direction. It will force the soil and small stones to go over the top of the plane instead of underneath it which is lifting the plane off the ground giving you the lumps and bumps.

Only watched about 3 minutes so far. Such craftsmanship, you should be proud. I'm wondering if larger diameter cylinder's would have better effect?

I can have the plan I would like to reproduce it in a games room

Is this a rig for kids? He barley fits in there. The wheel is between his legs and the knees are bent way to much.

it is bullshhit, it will not work

Engineer a way to walk it without having to use the boom to travel and manouver

Little too wet

Thanks for sharing

Fantastic job

Great explanation and demonstration.

As a home made box blade, I wouldn't judge it on a wet road. My 5ft box blade wouldn't be great on our wet road right now either. I'd say, wait till it dries out a little, then try it again. I'd say, it did pretty good, all things considered. My box blade has 5 or 6 adjustable-height teeth on it, that would be easy to add for you, if you needed to rough up the surfave a little. Other than that, I'd say you've got yourself a decent boxblade!

I think if it were dragged by a chain, that would allow it to float. I think what you have here works like a grader blade.

Too bad your motor isn't reversible because you could Chang direction just by flipping a switch and the handle position

“;-)”

41

Uhocuhiciuh

Fhbch

41

Infhuiv😊😊

Mncruhc

Ffufhuh

Hghuif😊

😂

The content we all need

Love my 77 dt400!

I'm interested got any for sale