Thank you 👍

I picked up this saw with stand for $50 as a return. No complaints about that. I found that the fence was the most annoying part of the saw, though much easier to use than many other entry-level saws. Measuring the right side of the fence to the edge of the main table and subtract from 10" will give you a very close cutoff dimension. So if I wanted to rip something to 3-1/2" I would just measure the fence to the edge of the table to 6-1/2" and it would be right on. The saw came with no accessories when I bought it, I called up Kobalt and they sent me every accessory for free, just took about 3 weeks to come in the mail but included everything that came with the saw originally.

What to do when your crown is wood finished?

I really appreciate your video. Followed your steps exactly and everything went great. Project time: from gathering tools, clean up, returning tools, 1 hour 45 minutes. Complete novice, DYI’er , never done such a thing. Thank you once again. 👍

This is THE VIDEO to watch on this topic. Thank you for perfecting the art and for taking the time to share your skill with the rest of us!

I just bought 400 stones the same size as yours and they are sitting in my driveway right now waiting to be installed. I'm going to wait until the springtime because we already getting freezing temperatures here in Jersey

Great explanation of how to install, thank you. I'm trying to flush mount metal doors (20" tall by 32" wide by 1" thick square tubing with sheet metal exterior face) for a cargo box on my truck. I don't want to see the hinges. Is there a hinge available for my application?

If I did this job the way you are doing it here in New Jersey, within a few years those stones will be breaking apart and some would be sinking here and there. The way I was told how to do it you need to dig down about a foot and then fill the trench with concrete and set the stones in the concrete about 3/4 of an inch apart and you need to run a string along all the rocks to make sure they are all set at the same height

Im cutting cable😅

Thanks for the video. I have installed many, but it is always a long time between (and I may not do any more remodels if I want to preserve my 40 year marriage). As for Great Stuff ... your 50% success rate is much higher than mine.

What kind of sprayer is that

where did you get your metal roofing from?

My subfloor unthat that patio door is rotten , what should I do

Sir thank you so very much my husband and I wanted so bad to bring a face lift to our kitchen cabinets" so old" but everything is so expensive. So we are thinking about something like, and here you are. Now it's cold, we're probably starting measuring everthing by using home depot//Lowe's contractor designer for that then buy the unpainted cabinets during the spring. It has to be outside or garage project with circulated fresh air. You. We are saving your video, very clear, step by step and also comparing. We love it...❤❤❤❤❤

Im getting a new LG is the side vent even necessary?

Where did you order the gutters and associated parts from?

Do you have a link to the sprayer you are using?

Thank you, sir. This is the only detailed video that I have found of a pella 150 replacement window from the interior. Great job including every step. Thanks!

What nonsense, an amateur.

Going to try to do unfinished wood cabinets this weekend. Can we use a paint brush and roller instead of spray? Will the finish look close to being sprayed?

Thank you so much!

not the best way of doing it when the wires goes bad gonna need to remove a lot of pavers to replace, its better to run lights that work with conduit with your steps so in the future when a light goes out due to wires you just disconnect wires from light and pull out damaged wires and fish through new wire ,also retaining walls should sit on clean gravel as base and backfilled with gravel aswell so rain water can get out . anything with dust will eventually erode due to rain and cause uneven walls even failure its ok to save money but if you have to do it twice what did you really save!

Doesn't the door get secured also by the flanges? I see you snapped them off. Or are they really not needed.

You didn't install an electrical box. FIRED.

That little skirt on the lower outside is NOT that easy to clip on. I've NEVER been able to do that. I've had to cut a little channel on one side and then slide it on by tapping it with a mallet. I've also had success using a flat head screwdriver to go through the channel on the skirt and pry it open all the way down. This opens it up a bit so you can pop it on. In both cases, a liberal amount of non-petroleum lubricant is required. Also, the skirt is a little longer than the window is wide so it needs to be trimmed once installed. VERY POOR design. Otherwise, a nice product and easy installation.

How much or a price range you would charge ? In your location I'm from mid Hudson area Don't want to over charge my client

People tend to over build everything if you notice the old window dident have flashing tape silicone

By using a hvlp gravity sprayer, do you know if I need to thin the enamel paint?

It was great video and thank you for sharing. Quick question: what is the holder on the back of the saw for ( u shape) ? I just can’t figure it out??

Can they be washed mad reused with water based stains?

That would take a ridiculous amount of time on a job. I would never! Time is money

Does it leave space between the door and cupboard if no frames are used ? Also , how can I avoid those spaces..insects infestation might happen later

Dear True Grit, Please put a shirt on. Sincerely, Your neighbors

What paint finish did you do?

I think I'm buying this table saw from someone for $40 tomorrow. Tough to say no to that price.

So.... how did you secure the lantern?

i am very interested in the steps you didnt show, like storm window removal. It also looks like the interior side stops were already removed.

What kind of adhesive is that

Nice video. My cabinet door and hinge weren't exactly the same, but you answered some questions I had. I like your hinge template idea for predrilling holes.

Good video over all but better to leave a little more of gap between the siding block and the siding to allow for the siding to expand and contract. 1/4" would be find and give you a little more room to screw it in.

Very good informative video - thanks. Gives me some hope to try and repair mine now...

How did you secure the wood in the cart

I have two weights but I don’t see a second pulley

Thanks for taking the time to make this great, informative video. No music/fancy graphics just everything I need to know before starting my project.😊

Thanks so much! Lowes contractor wanted to charge and obscene amount of money to do what you just showed! DIY!!!

This method is good for scrubs. That’s why in the tile business they don’t do this dumb stuff. You’d be fired. The amount of time you took doing this bs, the job is done.

Video was very helpful 😊

Would you recommend using primer before painting if going with a dark color?

Perfect. Thank you for this great video!

Very informative thanks.