3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
4 жыл бұрын
4 жыл бұрын
4 жыл бұрын
4 жыл бұрын
Пікірлер
@timk282 17 күн бұрын
Thanks a ton!
@timk282 19 күн бұрын
How did you ensure alignment? I kind of liked the multi screen
@cornholecollective7116 18 күн бұрын
When you assemble your frames, attach the center beam last and stack them so they’re exactly the same. Then after attaching them to the decks, your frames should line up nicely.
@1stCMWARTIME Ай бұрын
Damn, you are so good and confident. I think, at least for anyway, you make it look way too easy 😂. If you make legs without a brace, it’s really easy. Adding the brace mainly for looks and some rigidity is the hard part. Equal angles of the boards is the hard part. You showed sanding down the leg rests to attain equal angles but not how you measure or equate the two leg angles. I’m a retired civil engineer and probably obsess on accuracy…😉
@cornholecollective7116 18 күн бұрын
There are so many factors that can cause wonky legs. Frame isn’t square, bolt holes in the legs aren’t centered, bolt holes in the side rails aren’t exactly the same, even the width of the legs isn’t precise. My answer to all of these: jigs.
@carpe_poon5761 Ай бұрын
On the website it says 47.5”. In the video you say 47.25”
@cornholecollective7116 18 күн бұрын
I trimmed a bit in the 2 years between the website write up and the videos.
@YNLEXPOSURE 2 ай бұрын
All collective videos are great! I just finished my second set. I’m in Reno NV, hot day temperatures and under 10% humidity. I now do my finishing in morning with temps under 70. I’ve used thinner coats but will have to try your heavier method so it stays fully wet before I stop brushing. I use Polycrylic. Any extra tips for such dry conditions? Is your brand of finish better? Thank you
@cornholecollective7116 2 ай бұрын
A fellow Nevadan! I’m in LV. Tips, No fans. Thinner coats, using a squeegee to get the first coat on quickly works well.
@YNLEXPOSURE 2 ай бұрын
@@cornholecollective7116 You know heat better than I, lol. Squeegee!!! Like a rubber one for window washing?!
@duanecalhoon3322 2 ай бұрын
I can't seem to get past air bubbles when using polycrylic and poly urethane, any tips???
@cornholecollective7116 2 ай бұрын
Unlike Bond, always stirred, never shaken. Also, thinner coats, use a very dense foam brush or a firm dense bristle brush. The floppy foam brushes can lead to more bubbles. Never roll it in.
@MASTER_DAD 3 ай бұрын
Great video!
@YNLEXPOSURE 3 ай бұрын
Thanks for a great video! I’m finishing my second set of boards. I’m amazed how easy you make it look drilling through your side boards free hand. I’m finding variation in the holes angle from side to side will make the crossbrace not fit flat on each leg.
@cornholecollective7116 3 ай бұрын
100% if the bolt holes aren’t exactly the same and the holes in the legs aren’t exactly the same, the leg angles will be off and the brace will make them wonky.
@YNLEXPOSURE 3 ай бұрын
@@cornholecollective7116 so you have calibrated drill skills? Starting the hole exactly x amount from end frame is simple enough but drilling through the side frame exactly 90 degrees free hand seems dubious. Guess I'd expect you'd drill them on the drill press before frame assembly??
@sleighit2151 3 ай бұрын
Once you get it finished with the stain do you need to seal it with anything to help protect it from weather if left outside? Also did you pull off the vinyl while the stain was wet or wait until it is dry. Just purchased my first set and wanting to put out initials (both of ours are the same once married) and use at our wedding.
@cornholecollective7116 3 ай бұрын
Congrats! Definitely seal the set when all the decoration is done. Recommend water based sealer like Minwax Polycrylic or Rustoleum Parks Pro Finisher. Lots of coats. There are some videos I posted about finishing steps. You can pull the stencil right after staining or painting if you’re using gel stains or acrylic paint. No need to wait. You do need to let it fully dry before using the liquid clear coat.
@K342ly 3 ай бұрын
Would this method of sealing work over sharpie?
@cornholecollective7116 3 ай бұрын
I’d suggest spraying a water based poly first then the liquid over that. Try a test piece first. It’s what I always use the hole cutouts for. Should be good.
@dreamlookautodetailingauto3353 3 ай бұрын
I use a 6 inch hole saw. I don't know why people have so much trouble with it? They might be pushing down too hard? I use little down pressure, cut halfway down. Flip the board over & cut the rest. No tear out...easy peasy. 😉
@cornholecollective7116 3 ай бұрын
Nothing wrong with a hole saw.
@YNLEXPOSURE 3 ай бұрын
Great video series! What is the price in 2024 for a Raider board set as shown here?
@cornholecollective7116 3 ай бұрын
Not selling boards lately. A good builder with nice custom bags would probably be around $350-$400
@madsciencesac 3 ай бұрын
The "semi-gloss" at the end...is that different than the polyurethane you showed in the beginning?
@timothymalte6363 3 ай бұрын
What type of vinyl are you using for your stencils?
@cornholecollective7116 2 ай бұрын
Oracal 631
@ashleymyles7697 4 ай бұрын
Do you lightly stain the entire board and then put the stencil down and make the image a darker stain? If I did this should I use the gel stain for all of it?
@cornholecollective7116 3 ай бұрын
Staining over stain doesn’t work too well. Stains tend to “seal” the wood and the next coat smears a bit. It can be done if the first coat is really light and the next is very dark. I prefer to do the opposite, staining the dark image first let it dry a long while then stain the “background” and over top of the dark image.
@sjb3460 4 ай бұрын
STUPID MUSIC!!!!!!!!!!!!!!!!!!!!!
@benjaminl3084 7 ай бұрын
Awesome video Scott! When you were aligning the mountain stencil over the MOSS you already did were you eyeballing it or did you have registration marks? Also what was the clear transfer tape you used? I've only seen the white. Sorry last question. What vinyl software you use and was it hard to learn?
@cornholecollective7116 6 ай бұрын
Howdy! You can find clear reusable transfer tape at hobby lobbybor Michaels. I don't live how high-tack it is hutbit helps to align intricate stencils. This particular design was all one stencil. i use VinylMaster software, it came with my UsCutter machine.
@benjaminl3084 6 ай бұрын
@@cornholecollective7116 did you just eyeball the alignment then or have registration marks? Thanks for all the info!
@kimberlywebb5481 7 ай бұрын
I have a stencil I was planning on using but this looks way better to prevent bleed through. Do you sell this sticker stencil?
@cornholecollective7116 6 ай бұрын
Hi! You van find lots of builders who also sell stencils at cornholecollective.com/friends
@RonInAVan 7 ай бұрын
Nice 👍🏻 does it matter what direction you cut the plywood for the side rails?
@cornholecollective7116 3 ай бұрын
Not really. Especially with very blond plywood like baltic.
@TedKrzywonos 7 ай бұрын
First of all love your videos and thanks. I've just fully stained my boards and will be applying stencils so I can paint. Should I apply stencils right on the stained board and paint or add a coat of poly first before stencil/paint.
@cornholecollective7116 7 ай бұрын
I think you’re applying decals to a stained board, that’s totally fine. If you’re applying stencils as a mask to paint designs over a stained background, it’s best to poly first to protect the stained area. The mask can pull up some of the stained wood fibers when you remove it. Hope this helps!
@thomasash4100 7 ай бұрын
This video might have been only 1 hr if alot of the BS talking was left out. To me this video got very boring.
@cornholecollective7116 7 ай бұрын
Thanks for the feedback, what’s your channel? I’ll check that out and give you feedback.
@SableSunsets 8 ай бұрын
Damn love this so much!!!
@jumpingguyproductions 8 ай бұрын
Super helpful. Thank you.
@chacepruismann4584 8 ай бұрын
Did you do this all in one day or was this multiple days
@cornholecollective7116 7 ай бұрын
That was all a single take. :) poly over speeds up the process a lot.
@richardgallo3500 9 ай бұрын
I’ve made a wooden rail jig. I like your idea better. Thank you.
@MarilynSmith-v1d 9 ай бұрын
Is it possible to use a glass enamel paint and get a slick? Enough surface, or can you go over the gloss? Enamel paint with polyuresin the enamel paint is an oil base
@cornholecollective7116 9 ай бұрын
This is a tricky one because you’ll want to seal the board with poly and poly doesn’t adhere to glossy paint well. It might appear to hut in no time the layers over the glossy area will peel up and look terrible. The glossy paint doesn’t make a lot of sense considering the whole board will have to have the same sheen for the bags to slide right. I’d say use normal acrylic paint and glossy water based poly if you want them shiny.
@ConstantGardener-q9q 10 ай бұрын
I’ve also seen a free hand method of “painting” an image with dark gel stain onto light wood, waiting for it to dry and then staining over the whole piece with ether a lighter stain or dark stain over everything to give it uniformity
@cornholecollective7116 10 ай бұрын
Yes! If you have the time, this is the same as the poly-over method but without the poly. Some gel stains and environments have unpredictable cure times and the last thing you want is to smear the dark when you apply the medium or dark shade. It definitely works though when you have all those factors under control.
@bandd1952 11 ай бұрын
Great job and tutorial. I just finished my first set and it came out great! Question. How do you finish the sides and legs? I was thinking of exterior paint or maybe colored stain. Your thoughts.
@cornholecollective7116 11 ай бұрын
If you’re staining or painting the frames, i definitely recommend rounding over after you paint/stain. Cuts a nice clean edge. Suggest a color that’s contrasts a lot with the top deck. Really, your choice. Good luck!
@underdogstudio1 11 ай бұрын
Thank you great tutorial! I ended up getting spar urethane oil base because all of the water based polyurethane said interior on the can. I haven't applied it yet. Can the poly be used for exterior? Thanks again!
@cornholecollective7116 11 ай бұрын
Great question, anything oil based is likely to yellow quite a bit. It also tents to be a lot slicker. Water based poly may not hold up well if you leave your boards outside but it works great for playability and is durable enough. Definitely the most common among builders.
@stevebuteux8218 11 ай бұрын
Love these. Question about the friction blocks to keep the boards together. My support board is just off enough that the two boards don't match perfectly for the friction blocks the way you describe. Rather than fitting the blocks tightly on either side of the brace, would placing them further apart still achieve the same effect of clamping the boards together? I imagine the boards could slide a bit length-wide but they'd probably hold together for the most part. Not ideal but do you foresee a big issue? Thanks so much for all your videos.
@cornholecollective7116 11 ай бұрын
That does make sense. When my boards dontnline up perfectly, i sand down the edge on the inside of one of the “buckteeth” if that makes sense. Most of the time, it works every time.
@danieldibiaso9342 11 ай бұрын
The camera is so far away no idea of what the. Odors look like. Useless video
@wcw7398 Жыл бұрын
I think I understand how the poly would seal the stain, and allow application of the new color, but I'm not sure how the stain would properly under the coat of poly.
@cornholecollective7116 Жыл бұрын
This might be specific to gel stains but a thin coax of sprayed on water based poly doesnt interfere with the way they cure at all. You can do a stain over stain without the poly butbut takes a lot longer and the darker colors still smear sometimes.
@wcw7398 Жыл бұрын
@@cornholecollective7116 Thanks for the reply. I'll give it go! And thanks for the video. Very informative.
@spartansfan1995 Жыл бұрын
Do you stain the rest of the frame and legs or do you just do a poly coat on it or just leave it?
@cornholecollective7116 Жыл бұрын
I always poly the frame and legs. Staining or painting the frames, Really depends on the look you want. I rarely paint or stain the legs ither than logos on the brace.
@alfredovilla4023 Жыл бұрын
Great video! What's the link for the wood plugs on Amazon. It's linked to a miter saw.😅
@cornholecollective7116 Жыл бұрын
Oops! amzn.to/3ZUkaPx
@dmanisit2424 Жыл бұрын
Great camera work
@cornholecollective7116 Жыл бұрын
Lol. Yeah, I know, it’s shit. Oh well.
@SuburbanDon Жыл бұрын
This is the first complete and practical set of instructions I've been able to find. I wish I had found it before I built and finished my first board. Thanks.
@cornholecollective7116 Жыл бұрын
Thanks for watching!
@williamsills9399 Жыл бұрын
How did you keep the stain from bleeding under the vinyl?
@cornholecollective7116 Жыл бұрын
Gel stain applied sparingly. Try it!
@nathancronrath1407 Жыл бұрын
Do you finish the legs while they are attached to the frame or do you remove them before you finish them?
@cornholecollective7116 Жыл бұрын
I leave the legs attached and apply a couple coats of clear to them. Once they’re built, I don’t like removing the legs.
@jayrose9463 Жыл бұрын
I thought about three crosscuts for the four boards Never thought about grain direction
@cornholecollective7116 Жыл бұрын
If you’re fully painting or wrapping the boards, that might be an easier way. My personal preference is the look of long grain and avoiding tear outs with an 8’ ripcut. It can be a lot to juggle if you don’t have a helper or full size table saw.
@mcandg6604 Жыл бұрын
Im going to b painting my first set this week this video inspired me!
@cornholecollective7116 Жыл бұрын
I’m sure it’ll be great!
@philborland2003 Жыл бұрын
Thanks for your great videos. I’ve made several boards using your technique and had great results. This time however instead of poly I used epoxy resin on the tops and they turned out really nice. I think I want to apply several coats of poly to protect the finish from scratches and I was wondering if you had any tips for me. Such as water based or oil base poly and how many coats. Any suggestions would be greatly appreciated.
@cornholecollective7116 Жыл бұрын
Poly over resin?! That might be above my pay grade bud. I would seriously doubt that super glossy poly would be more scratch resistant than epoxy but I don’t have anything to prove one way or the other. Please follow up here and let us know how and what you applied over the resin.
@chrispfeffer9024 Жыл бұрын
Love the boards. I been debating on staining with multiple stains. Any advice?
@cornholecollective7116 Жыл бұрын
Thanks! Multiple stains is my favorite method of all. Have a couple videos on the “poly over” method using several shades of stain. Unfortunately, it doesn’t work with dyed staines but it works great with brown shades.
@scottglesmer137 Жыл бұрын
What angle are the legs cut at
@cornholecollective7116 Жыл бұрын
Builder preference. There is no rule about leg angle but some say a more raked out leg absorbs some of the bag shock so less bounce, personally, I doubt it has much effect.
@mattandmelwilliams Жыл бұрын
Scott, I’m late to the show, but I intended to make some boards for the first time this weekend thinking I had a plan….. until I watched this! Well done.
@cornholecollective7116 Жыл бұрын
Folding angled legs with a leg brace seem easy enough but there are a lot of variables that can throw them off. If you’re not mass producing boards, the hang-off-the-table method is the best I’ve found.
@alexkalinkou1817 Жыл бұрын
This is fantastic!!!!
@cornholecollective7116 Жыл бұрын
Thanks Alex!
@russellscorner6531 Жыл бұрын
You ever try to use the Baltic birch as the frame? That would be a nice look I think with the end grain exposed.
@cornholecollective7116 Жыл бұрын
If I had space and money for a full size table saw, I’d definitely rip baltic birch frames. They work great and you don’t have to worry about the inconsistency of normal lumber.
@caseypace6810 Жыл бұрын
I just attempted my first set went well so far until the hold low saw slipped but I have a light ring so it doesn't really matter. Idk that I'd build another set I'd rather just purchase once and be done
@cornholecollective7116 Жыл бұрын
If it’s just to make a set your yourself, especially without many tools, buying is usually the right choice.
@PNWLiving1725 Жыл бұрын
I'm impressed on all the info you give. It helps to know the details
@salcamp01 Жыл бұрын
Does the spray varathane poly not absorb the stain? I notice you got right over those areas with the 2nd stain…thx nice video I plan to try it
@cornholecollective7116 Жыл бұрын
Great question. If you stain light over dark it can smear the dark stain. The poly seals the dark stain so that doesn’t happen.
@ryank9910 Жыл бұрын
Looks great 👍