My regulator cable is broken … Where can i find it ? Thank you .

All you have to do is push in on that white piece to release it.

Now do #8

Hello, I need help. I have a 2016 Ford F150 with a 2.7 turbo and it started off burning oil and sometimes white smoke when driving and hesitation I need help. I don’t know what’s wrong with it. Everyone keeps telling me to put a new motor in it, but it drives it runs. Can you please tell me where and how to get help?

I appreciate your time thank you. 🙏

Mine just started at 206,000.

it's been a while...thx for the refresher.... nice video....

Awesome video. My 2014 gmc sierra was exactly like this. Did steps as described in video. Certainly saved a lot of time guessing how. Thanks for posting !

When I turn the shift out of low, it bounces back. Tranny in neutral. ???

Hello, how difficult to get to and take off the lower radiator hose? Assuming you wentt under the truck?

I must say excellent camara man skills, holding that thing while getting them clips off and back on BRAVO LOL great video man thanks

Thx for the great and informative video.

None of these video ever show the passage side.. must be a pain in the ass!

At minute 7:25, you disconnect a cable (purple lock), which are those silver tubes where the cable you removed is connected. I need those plugs and I don't know how to look for them, thank you very much.

Nicely shown quick and efficient.

Great job / video...

Thanks a lot

Thanks so much man!

I installed the motor but it won’t work 🤦🏻‍♂️🤷🏻‍♂️😤

I know he said removing the tire was optional... But wow , I guess it's a requirement for me now 🤣

Great video

sorry for the 4 year old video question but would this fuel pump work on a 2018 Nissan NV3500 W/5.6L VK56?DE???

Good video just did number 4 cylinder on a 6.2 with broken spring. Luckily keepers were intact

Thanks for skipping major steps on how to take the intake tube off. I guess you struggled with it and instead of being a man, you edited out and skip the whole part about the 1/2 fucking rivet that the tube is bracketed into. Thanks for the partial information

This here was a AWESOME video,Thank you so much for the Video ..I was able to save myself $365 thanks to this awesome video.. EPIC

By the way you've done an outstanding job of instruction on this, and I really appreciate it.

I'm ready to put everything back I've actually already reinstall the starter on my Titan but I have as yet to reinstall the intake is there a way to test that starter without putting the intake back on. The reason I asked is I hooked up all the wires to the starter and put the battery cable on and just tried to see if it would turn over to make sure the starter would work but it didn't do anything so I'm kind of in holding mode right now I can't find anybody that knows if it should turn over in that condition or not or if I actually have to put it all back together before it will crank. Does that make sense? If you have any ideas please let me know thanks

Good video I always replace oil line while in there

You know its a ford when the first step to change a damn bulb is to remove the whole grille 😂 pos company.

I installed the new radiator and filled it up but it is still overheating. Maybe it has air pockets in the system? Also no leaks.

About how many hours do you think I would take to do both sides ?

Great video. Really appreciate the thoroughness without going overboard. This was great!

Thank you for sharing your knowledge 🙏

Thank you.

I have seen other repairs utilize the brake caliper reversed with three nuts in to pull the axle shaft out fairly easily.

Hey, just have the car started pull the negative off the battery post if it shuts off it’s your alternator

Outstanding video. Thank you. Changed my water pump today. This video was absolutely perfect.

Ford dealer told me it would cost $2500 to change this pan. Does that sound right? They said it would be 8hrs labor is why. I do have 4x4 but does this sound correct?

How much is labor only?

Hey man, cant get that little tab/ kickstand to disingage, its stuck, what do i di?

Also, Great video and thank you for the help in doing this job on my 04 4WD SE.

The 3 wheel bearing bolts installed from the back are 101ft.lbs. not 145. The 145 is the NM spec. Source - I just downloaded the Factory service manual.

My 2013 F150 3.5 ecoboost needs a new motor, having the 11 stud manifold and new transmision flulid lines put on while the engine is out. Getting a Jasper Remanufactured engine put in

You need the 11 stud manifold, less likely to have problems.

Thank you, you saved me $500 (net). Got one at ROK auto for $60.

2:25 link in the description for both this pump and a hand pump??? Inquiring minds want to know.

It seems like you can replace those fitting without taking out the turbo.

Are you able to get the oil line screen out when the turbo and manifold removed or do you have to move the AC compressor and evacuate refrigerant?

Awesome step by step tutorial, thanks!

is this the same engine as the 2015 ford transit with 3.5?