GM 5.3 L83 & 6.2 L86 Intake Manifold Swap 2014+ (Complete Guide)

[@agp9844]

I did this with throttle body headers and dyno tune made major differences

[@Mel7eds]

I heard just a tune can wake the trucks up substantially vs no tune

[@conklinb1977]

Hp tuners also has a spot for the volume of the intake that prob needs changed on the GEN V 5.3

[@chronicmat5787]

great video i’m young and this helps a lot blessings !

[@buddyrebel_Garcia]

@13:52 I didn't change the 6.2 intake, it wasn't even that much of a hassle. All I did was put some lube on the inner of the 5.3 intake and with a flat screw driver slipped in the 5.3 intake into the 6.2 throttle body. No need to to waste more money when it isn't even a hassle. But good video.

[@xandersmith9832]

Thank you for putting good educational info out there

[@AaronHinesAuto]

Glad you like it! Thanks for the support

[@96tahoe2dr4]

​@AaronHinesAuto just outta curiosity can u put an L8T intake manifold instead of a l86?

[@davidcarr4464]

@ Aaron The last thing you want to do is run the engine lean, I get it. I don’t think the 6.2 intake and throttle body would make that much of a difference. I think the oxygen sensors along with the MAF sensor would give the ECM enough info to pulse the injectors on a little longer. I mean its always looking at short term and long-term fuel trims so you think if the 6.2 intake/throttle body swap made it a little leaner, the ECM would adjust for that. Your thoughts.

[@ryanakey1599]

You are correct the ecm will accommodate and adjust with just the l86 intake manifold l86 Tb and a 3.5 inch cold air intake it will adjust its self and no lean codes are thrown. I just did the swap this week and no lean codes no tune.. the map on the l83 and l84 are rich enough to accept the l86 swap

[@johnlundquist4846]

this video is so helpful. so much good insight and explanation! used your links to purchased the l83 intake! rock on buddie

[@choklo187]

Will I gain more hp on my 2012 5.3 if I put an intake manifold from a 6.0 or 6.2 of the same year range? If so how much? Is it a direct bolt on?

[@LuisTorres-ft9nq]

you listed the lt2 manifold as the lt1? or am i confused

[@arcamediuas]

Nice video, very informative. Do you have any input on values for throttle bodies larger than the 95mm? Do you think a L86 manifold can be ported to fit a 103mm throttle body, or do you think anything more than a 95mm we are at the limits of the manifold?

[@TheJishwa]

i been looking for video like this awhile thanks for help

[@AaronHinesAuto]

Glad to hear, thank you!

[@TheJishwa]

@@AaronHinesAuto do you think I could c8 engine cover on manifold?

[@TheMrmmkkpro]

Came across this video as I am searching for help doing AFM delete 15 6.2 silverado. Excellent work, direct and to the point with very pertinent information. Subbed. 👍👍🏁🏁

[@thatrealcarguy]

So I could use my Camaros LT1 intake on my 2017 5.3? I still have manifold and TB from my 2018 Camaro SS.

[@marcusdalton2230]

Can I use the L83 intake on my Gen 3 LM7 engine?

[@Patzfan4eva]

If you have added a edge CTS3 programmer, cold air intake and cat back exhaust, any advice on tuner changes needed to maximize this modification.

[@rickjellison959]

what intake cover do I need for the L86? Is it the same as the L83?

[@clifford2slow20]

did my l86 tb and Intake manifold and I started having a bad misfires in 3 different cylinders

[@carlomendoza8588]

Did you find the problem? I want to do the swap

[@clifford2slow20]

@ yeah I ended up picking up a bad throttle body .

[@clifford2slow20]

@ if you buy one used make sure it’s a 6 pin my mistake was that I picked up a 5 pin one

[@carlomendoza8588]

@@clifford2slow20 thank you for the help!

[@hugodiniro]

Any work to the fueling side ? Since air was adjusted ?

[@jruizh793]

Do you have a video on how to install the lt2 intake

[@jayer-su3hu]

Can anyone tell me if this is a "plug n play" swap or will my ECM need tuning afterwards?

[@j.d.7321]

Great video. But all that hype and no test run or performance review??

[@j_rod75]

I did this swap and have not had any tuning. I have noticed harder shift at times from 2nd into 3rd, mostly when getting on it. Is this because of these air volumes being to low now?

[@flowmagic5]

I’ve been hearing this and I’m about to do this same thing to my truck! But is ur truck running good? Only whe you get on it it shifts hard? That might be because of the amount of air that now is getting for sure no big deal bro

[@j_rod75]

@@flowmagic5 I don’t think it has anything to do with the bigger intake now. I put my stock intake back on and it still does it. I’m debating putting it back on but if I do and decide to spend more money I’m getting a tune at the same time.

[@quintenbrown1508]

So do I need to buy a 6.2 cold air intake

[@jaycastillo9313]

At the end of the video you say “And continue with any tuning you need to do” is there anything else that needs to be tuned with this swap or just the airflow parameter being increased? Thanks.

[@quintenbrown1508]

So can you use a banks programmer

[@bigohubcity3159]

Do you have to tap the back of the manifold for the brake booster if going in a 2014 chevy truck

[@AaronHinesAuto]

No, vacuum on those trucks are from a pump off the belt

[@arevalosgarage1275]

@@AaronHinesAuto very helpful thanks.

[@AlfredoLT]

Where did you Get the throttle body coupler?

[@alexvarela9154]

What up Aaron... quick question???? What your opinion on oil catch cans...

[@hunterhbb]

so this does work for 2016 5.3L silverado’s?

[@christopherbrockway2035]

What kinda tune do I need to do this swap and how much is the tune

[@timharris4249]

Aron, I don't have a cam but my exhaust is modified headers, no cats with maxiflo. Will the Lt2 help me or Lt1 be more practical?

[@hi-fi3889]

Can you comment on tube adjustments for a l83 using the l86 intake manifold? My truck is tuned by Blackbear and they offer free adjustments but is this something that can be done efficiently, remotely?

[@theartofwanderlust]

Great video, thanks for posting

[@AlfredoLT]

For the bolts from the website in the description do I need to add 10 of them?

[@samcorne4773]

what was the torque specs for the throttle bottle bolts?

[@michaelgabert4261]

If i swapped to the l86 and upgraded to the jet 76116 performance throttle body should i switch the air flo sensor to either the jet 69180 (which i think is for a 6.2) or jet 69189 (which should be for 5.3). Thx in advance, great video. Convinced me to do the swap, lol.

[@jrltx23]

Used your video on 16 Silverado for long tubes got everything done to factory specs. So I have Long tubes, E85, cai and tune which manifold would be better for my setup L86 or LT2?

[@JoseAvila-le7dr]

Thanks another for you helping videos, aney help on removing a seized intake manifold on a 05 titan.

[@1_SLOW_WORKTRUCK]

Quick question might be a dumb one but does the lt1 & Lt2 use the same size/length manifold bolts?

[@jefffnuts6179]

No

[@morganpayne5404]

I’m about to do this swap on my truck. Did a DOD delete and stage 2 cam from Texas speed already with High flow cats and cat back exhaust. Will the stock intake manifold cover still go on the new l86 intake? I saw you didn’t put it on and I’ve assumed it won’t fit but I’m just curious. I haven’t read all the comments so this may have been asked already.

[@Mel7eds]

Apparently it does fit per previous reply to another comment asking. Hopefully they’re right and hope it works for you

[@pedrocollazo4437]

How is it running with the stage 2?

[@VAlien79]

Any reason my l86 intake manifold would have a extra vacuum port on the drivers side on the back towards the firewall? I did the swap everything bolted up great and noticed the port was causing a lean fuel trim. I plugged it with a cap and everything runs fine now and no CEL or codes?

[@theborderboyz]

My l83 has that port you’re referring to. I know it’s a year late but I would confirm it’s in fact an l86 intake

[@VAlien79]

@@theborderboyz thanks for the reply! Do you have any lines going to this port? Or do you have it capped off…. My original l83 that I took off didn’t here the port and the throttle buddy opening was smaller then the one I have on now.

[@jesusresendez7064]

Quick question. Will this void warrenty or will the check engine light come up?

[@sbc_jake_9677]

Warranty is voided if a modification you installed causes an issue or failure. Also you change anything in the factory tuning as well

[@mateo801]

How long does it take to just pull the manifold?

[@willallen126]

I did mine in less than 2hrs. 10mm deep well and a cpl extensions worked for me. Factory cover fits on the 6.2 as well. I didn’t even take mine off. Just slid everything out and back in. 454chuy ported l86 intake and throttle body. Make sure you unplug your battery

[@bbenton1996]

Considering doing this to my truck, I have a Volant CAI and will be moving to a 93 Diablo tune. Will I need to change the air values still?

[@ryanaustin1970]

nope i have gm perf CAI and the trinity 2 tuner , no issues

[@mad_max2065]

Badass video

[@AaronHinesAuto]

Thank u!

[@ROCKSTAR9808]

I have an aftermarket cold air intake, does the coupling stretch over to the new TB?

[@AaronHinesAuto]

Yes. This truck had a volant CAI. It fit just fine

[@pg925able]

I also have the Volant CAI, it made such a difference, Im swapping for the 6.2 throttle body and intake manifold on Saturday for my 2016 Silverado. Just wondering 2 things. Does the intake manifold cover from the 5.3 manifold fit on the 6.2 manifold? If not...then where do I leave the wires that were removed from the back of the manifold cover. I appreciate your help.

[@asifaman9693]

I have gm sierra 2015 6.L l83... Can anyone help me in which model of holley or fast intake manifold is compatible with my car.. With 95mm throttle body and afe mg momentum filter 3 1/2 diameter size.. Please help me someone

[@mrarmy300]

Wow, very thorough, thanks for sharing! Are you aware of any intake I can swap onto my Gen IV 5.3?

[@martygrajeda3457]

Aaron, I was able to pick up a 5.3 Gen 5 L83 motor. This intake will work on it?

[@forgottenchild7935]

I did this swap and started the truck to check for leaks it ran well but started to stumble and sputter until it stalled after warming up, The truck will start right back up. is this due to it not being tuned? or did i screw something up? also no cel or pending codes in the scan tool. any advice from anyone would be appreciated.

[@flowmagic5]

You need a relearn bro

[@forgottenchild7935]

@@flowmagic5 actually my brand new 02 SENSOR was trash. Replaced it and all good

[@flowmagic5]

@@forgottenchild7935 haha damn bro so is ur truck running smoothly now? Even tho is not tune or anything ?

[@flowmagic5]

@@forgottenchild7935 there gonna install mine tomorrow and I’m nervous lol😂😂

[@forgottenchild7935]

@@flowmagic5 the tuner identified the bad 02 so I fixed it and they sent me the custom tune. so the truck is fixed and tuned. runs strong

[@reaper7613]

Can I talk this on a 2011 GMC Sierra 1500?

[@sbc_jake_9677]

This mod only works on gen v v8s

[@txlt498]

So we don't have to relocate the alternator for the lt2 intake?

[@AaronHinesAuto]

No sir

[@txlt498]

@@AaronHinesAuto ok thank you

[@motorizedmiscreant]

@@AaronHinesAuto did you find out the numbers for the LT2 my man?

[@dandrehancock1146]

What would happen if you didn’t change the air flow valve?

[@pg925able]

I am wondering the exact same thing.

[@alexisnbs492]

Same

[@smallstreetcruz31]

Anyone have a lt1 installment video

[@pg925able]

I'm swapping for the 6.2 throttle body and intake manifold on Saturday for my 2016 Silverado. Just wondering 2 things. Does the intake manifold cover (engine cover) from the 5.3 manifold fit on the 6.2 manifold? If not...then where do I leave the wires that were removed from the back of the manifold cover. I appreciate your help.

[@ryanaustin1970]

covers are the same , the bundle of wires can ( although should be tied up) lay on the back of the engine without any issues

[@PhillyDee215]

Nice video bro👍those years don't have knock sensors under the plenum🤔

[@jaycastillo9313]

That stopped in like 2007

[@PhillyDee215]

@@jaycastillo9313 yup👍

[@edagr8753]

What would the values be for the throttle on HP tuners if L86 intake was ported?

[@covaelite1]

It would still be whatever value your throttle bore was.

[@shmellyhandsprod]

Did it LT2 L83 but belt didn't fit too small tuner had to get 1 FYI 😂🤙🏽 went with LT5 TB any tuners wanna help my guy out lil gurgley on the low but gets it after around 2000 rpm I do have a 2500 stall converter with a stage 2 BTR cam on bubbi the burban whale 🤙🏽🤙🏽🐳

[@ltx_chuy3562]

This with the throttle body from a ZR1 💪🏻

[@Hutt92]

Man be careful torquing the intake manifold bolts my torque wrench only went down to 10ft lbs the bolts call for 8 ft lbs I figured it would be fine I ended up snapping one off at 10ft lbs had to get a die grinder in there and grind it flat drill it out and use an easy out to get it out

[@ryanaustin1970]

putting either the LT1 or LT2 intakes on a truck is NOT a performance improvement , it is a down grade . you make less torque and gain very little horsepower , considering trucks and suvs need torque to move their fat asses they need all the torque they can get . a huge improvement is custom tune , CAI , ported L86 intake with ZR1 throttle body

[@ryanaustin1970]

also ABSOLUTELY do not need to tune or relearn anything going from 5.3 to 6.2 t.b ...i did it , zero problems , now if your were to buy ICT billet adaptor and run a ZR1 throttle body then yes it would need to be done . youre forgetting these trucks tend to run a little "fat" on the air fuel ratios

[@TheJishwa]

@@ryanaustin1970 I have ported lt2 intake and ported l86 tb and get 40whp more 👀

[@ryanaustin1970]

@@TheJishwa bull fucking shit.. a stock motor and just swapping an intake show me the dyno video lmao 🤣 😂 😆

[@TheJishwa]

@@ryanaustin1970 I have dyno numbers 🤔

[@ryanaustin1970]

@@TheJishwa sure buddy ... ok so let's see the video .. stock l86 with just an intake swap gaining 40 wheel

[@closltx]

Can I use my stock l83 throttle body with the lt2 manifold?

[@AaronHinesAuto]

no sir, bolt pattern is different

[@smallstreetcruz31]

Can i use the stock throttle body on the lt1