How to get analog output ma from del p inwater column?
@muscatmama5 күн бұрын
Excellent explanation Sir🎉
@mareysaad65975 күн бұрын
Can I do the calibration without mounting the positioner on the valve ???
@user-vv7qp3id4p7 күн бұрын
How can we make RTD sensor circuit?
@Mk7J0K3R7 күн бұрын
Mines says negative drift after the remove gas prompt
@MrAwuna8 күн бұрын
Well understood, the Video is Educative and understanding
@muscatmama9 күн бұрын
Fantastic information
@jorgelomeli52910 күн бұрын
Zero it out
@MohanSundaram-fw7nz11 күн бұрын
Can we enter negative temperature value in the minimum temperature range ?
@Muambassaki11 күн бұрын
very usefull
@OTPOTPOTP11 күн бұрын
You used math to show two wire but not 3 wire. Could u do a vid with math for 3 wire so we can actually see its better
@OTPOTPOTP11 күн бұрын
I think you should use numbers to see that this only works if the fraction of resistors on the left side is one over one(same resistor top and bottom) not some other fraction like one over two e.t.c Because you can have a balanced bridge (the same fraction on both sides say 1/2 ) And get there with the variable resistor but it will be wrong. E.g with 10/20 resistors on left side i pretended to have 10 ohm resistive legs for sensor but with a 90 ohm sensor. That meant to variable resistor would stop at 40 as (40+10=50) top resistor and (90+10=100) bottom resistor giving a balanced bridge 1/2=50/100 but when we take to 40 we are yetting on variable and try to work out the sensor restance as we dont know we get 80 and not the desired 90 that it is.
@heidnaldodasilva52513 күн бұрын
Great video
@ugursux15 күн бұрын
Hey man. This is some great content. If you made a full process automation course I would buy it. Keep it up. Greetings from Istanbul 👍
Excellent video. Just one question, why do you use de Sf for Glycerine? Does it matter which Sf fluid is used?
@HG-jl4ed26 күн бұрын
Please help me with this What will be the output from temperature transmitter
@HARISHSUMAN-xj4ng9 күн бұрын
Resistance
@thumpsup321627 күн бұрын
More videos please.you are doing a good job.keep it going.
@sandracapoziello28 күн бұрын
Flow meter settings, I have been told many different settings.
@NilufarYassinАй бұрын
How to calculate that resistance?
@GrizzlyMcAdamsАй бұрын
If the boiler is idle or not at operating pressure, how does this effect the level? Will the LRV and URV need to be trimmed until the boiler is at operating pressure?
@ahadghorbanporАй бұрын
Goog job
@khalidkerbache7963Ай бұрын
Thanks Sir for explaining, can you explain pressure switch principle work.
@IKENNA369Ай бұрын
Please can you make a video on how to perform calibration of gas chromatograph using mono2020 software
@IgnatiusTabu-mi8lxАй бұрын
Does DPT has two equalizing valve as shared in this video? I thought it has only one equalizing valve,2 block valve and two vent valve.
@IKENNA369Ай бұрын
Some have two equalizer valves while others have one equaliser
@UChannel12Ай бұрын
Well explained, appreciate your efforts
@ProVest97Ай бұрын
Gosh, we've replaced so many of these with Hart-smart positioners, but I've calibrated so many of these and other positioners and I/Ps over 42 years.
@harinathiya4906Ай бұрын
How adjust travel length in positioner
@bayramalichoriyev6617Ай бұрын
Hello everyone this vedio is so useful for me thanks to the channel admin and do a lot of this kind of vedio 😊and in the future I will be great engineer and I will do a lot of great vedios about this field in my language ..from Uzbekistan❤
@kantabaytv5590Ай бұрын
Please do more instrumentation
@kantabaytv5590Ай бұрын
Please make a video how to connect the transmitter to input of plc and how it works
@maxartusy6378Ай бұрын
It is called a FLow-meter. It is also called a rotameter.
@asma.aydin2001Ай бұрын
How can I communicate with you please
@kadenburgart551Ай бұрын
Magnesium Chloride equilibrates to 33%RH, not 13%RH... www.engineeringtoolbox.com/salt-humidity-d_1887.html cameo.mfa.org/wiki/Saturated_salt_solutions nvlpubs.nist.gov/nistpubs/jres/81a/jresv81an1p89_a1b.pdf
@kadenburgart551Ай бұрын
I see that the Vaisala people said to only add 3ml of water for 30g of MgCl2. This is not a normal saturated mixture... maybe that's how they get 13% instead of 33%. This is weird. I have a 33%RH MgCl2 reference sitting in front of me right now. I just used it. 33%.
@kadenburgart551Ай бұрын
kzbin.info/www/bejne/l5avgYWQhrl0atk
@adedare1Ай бұрын
Thanks
@yoramgoodson4006Ай бұрын
I would love to know possible questions for instrumentation in acid plant. I'll appreciate
@user-tx8ek1hp5rАй бұрын
Hi I want to re range the transmitter from 200 l/sec to 300 l/sec what should I do
@francisv-ou7zjАй бұрын
Good
@belvinanderson6400Ай бұрын
Can I use the transmitter as a 2 wire or 4 wire
@jegansekar4787Ай бұрын
No. first you check transmitter mounting plat. Then you check it's 2 wire, 3 wire, 4 wire wire duel sensor. They mention in mounting plate. Then only you set 2,3,4 wire RTD.