This video was soooooo helpful! Thank you so much for your content. This is great! I was about to purchase a new caliper. I was just tubing how easy it was to replace before I made the decision and this video showed me that I can just replace the piston for $9 on rock auto

You're a Godsend. Many thanks

Thank you this help me a lot !!!

Good job explaining🤔

Thanks

Lol, I just remembered I don’t have a brake caliper press tool mine broke. Can I use some big pliers to press them back?

Thank you very much for the video. My first attempt was perfect because of you!

FY I! That was a quick fix, Thanks 😊

Thank you.

I wouldn't replace the fluid at that point. Lose friction taking out the dirty fluid. It shows it wasn't properly maintained. You might want to just clean the pan, the filter and replace a little, if any at all. Good chance of getting slippage with that lost friction. It will just speed the time table up on that doomed transmission.

I always wondered if goo gone really works.

This is a very good video. Nicely explained and filmed. Thank you !

At least oper the reservoir

Your video was magic!!!! It worked like a charm and saved me a bunch of $$$$

Thanks for the video. I rate it a difficulty of 4 out of 5 to get the filter out and a 1 out of 5 to get the new one in. (Don't try if.ypu have a.bad back..lol). In any case, you directions were accurate.

Great video 🎉 What size C-clamp was that?

Great video, replaced passenger side easy peezy

The Ryobi jigs only do the door side, they don't have a jig for the jamb side.

Thanks my sink is fixed and didn’t need maintenance to come

OLD CARS WORK FINE LIFE TIME TRANSMISSION FLUID CHANGE. 🎉

How to isolate the clutch so it doesn't move? Trying to fix my clutch and I don't have the impact tool. Please help asap.

EXCELLENT tutorial 😃👍 Saved me alot of hassle and money $$

Mine was literally frozen 😮 I pulled the spark plug and found ice 😢 Sprayed some Zep 45 inside the plug hole and got it going. Now to do an oil change

Thanks a lot for this video. I followed every step and accomplished the fix. Thanks again.

Thank you, you saved me hundreds of dollars from a plumber's charge!

IMO it is unnecessary to disassemble the cyclone, merely removing cyclone from the head and soaking in mild soapy water for a few hours should be enough. Make sure to let it dry thoroughly before assembly.

Your video was very helpful, thanks

Wow thanks

The following addition: - fill and sand any blemishes before applying fillers - use adhesive tape to create a rolled edge - after applying fillers, re-tape a little further outwards to avoid grey from the filler

thanks for the vid. I have a 2015 mazda 3, did a full flush at 100K on original fluid. Now have 250K miles and the mechanics are telling me not to touch it. what do you think? car is running ok, sluggish though.

Heeyyyy man, thanks very much for the video. Worked like a charm. Got a sub.

awe man, here i was hoping my fix would be just abit of tightening, my faucet leaks where the handle lifts up, i didnt check yet but im assuming ill have to get a new cartridge, how often should they be changed? my faucet was installed a little over a year.

Great video!

Thank you!

You just saved me a lot of time and money on this project. I have the same truck, even the color (280K and still running great). - Very clear and concise instructions. I would recommend the magnet for the handle screws. All was done in just over an hour. Thanks again!

Great job...totally helps me

Got the old one out. Got the new one in. You must have way more space than mine because there's no way I'm getting the connections done.

Outstanding explanation

The question is why. Why do you still have laminate countertops with drop in sinks in the third decade of the 21st century? Get rid of the whole top and put stone with undermount sinks. Your house value goes up. Better investment.

Just did this on my truck. Thank you for the video!

Man that black fox body is a beautiful

I use lipstick. This causes other problems when I have to explain why it’s in my arsenal!

There have been a lot of solid points made here and you've taken the criticisms like a champ. I would just like to say one thing for anyone who might read this. No amount of knowledge, planning or safety precautions can 100% prevent a catastrophic failure. It is a possibility no matter what. The best thing any pyro can do is not light these things within 150 feet or so of people, structures or anything flammable. I'm guilty of not doing it and I'm also fully aware that the worst could happen anytime without rhyme or reason. Pyro responsibly. Know the risks and don't lie to yourself. It is very tempting to ignore danger due to the overwhelming desire to put on a good show. Just my words of advice to whomever.

Seating the ring is a step you shoould be showing. Other than that, thanx.

Fantastic video! I have a 97 Toyota Camry with 150k on it. I don’t believe the trans fluid has ever been changed. Has a slight jerk from first to second at higher rpm. Would you recommend a change or a flush?

Excellent video man. I too am planning on doing a full GT40 H/C/I swap. Already have a set of 3 bar heads and an upper/lower intake from a 97 explorer. Still on the fence if I wanna add a cam or just have the heads and lower intake ported. Thoughts? Anyways, keep brining us the good content my friend. I also just subscribed =)

Man this was so helpful! Thank you so much. I followed those steps exactly and it freed up in the same spot. I got nervous for a second on my first try on the socket but a little extra push and off it went. Thanks again!

Did you really cut the corners out straight when the strike plate has radius corners?

That is a terrible job

Great video man. I have a set of GT40 heads from a 96 Explorer and was wondering if they are the same 1.6 stamped rockers you have there? Was also considering doing a small cam like and E303 or a TFS stage 1. Thoughts? Thanks man!!!