28 күн бұрын
Пікірлер
@nicbutterworth729 9 сағат бұрын
Slightly taller tail fin and rudder? As in not enough lateral stability?
@joshuawesterfield6635 9 сағат бұрын
Sounds loud as hell.
@AndyLazaris Күн бұрын
Building this now and looks great. Thank you. Have a question on wiring the 2812 LED Controller. I assume I have to solder some wires to the controller that plug into the receiver. Looking for a wiring diagram for the pwm, vbat, G, 5v. Help please cannot find it online. Thanks
@MarkoRoolaid Күн бұрын
I wired the controllers directly to the battery. Didn't use PWM. I had 4 leds and 3 controllers. Red, green and 2 white were connected to the 3rd controller. At first I thought I could control 4 different modes with the one controller, but I can't. In addition, do not connect led controllers directly to the receiver. ESC BEC does not allow such a high current requirement. I tested it myself and it didn't work
@AndyLazaris Күн бұрын
Ignore I figured out the wiring. Just not sure how I'm going to install since I glued up the fusilage already. Maybe extend the wires so they reach outside of the fusilage?
@AndyLazaris 21 сағат бұрын
@@MarkoRoolaid Thanks for the reply. I didn't see your comment before my reply. I used a servo extension cable cut off the end. Soldered the black to ground. White to pwm and orange to 5v. Then plugged that into the receiver. It worked after binding to transmitter. The esc seems to get hot fast maybe this is what you mean by not connecting directly to the receiver. as soon as i pull out the plug from the led the esc cools down. Not sure how to wire directly to the battery since the battery goes to the ESC?
@MarkoRoolaid 19 сағат бұрын
HI. You simply solder the red and black wires from the led controller connector to the ESC power connector. Matek controller works up to 2-6S. I didn't use PWM myself. Led controllers can also be set manually.
@scottstengel4438 2 күн бұрын
GOAT!
@pixeldude1335 2 күн бұрын
Was ist das für eine Folie mit der du den Flieger bespannst?
@MarkoRoolaid Күн бұрын
Hi, link here www.aliexpress.com/item/1005005137873497.html?spm=a2g0o.order_list.order_list_main.4.3ab91802IWWmQl
@pixeldude1335 Күн бұрын
@@MarkoRoolaid Danke!
@pixeldude1335 20 сағат бұрын
@@MarkoRoolaid Hast du schon mal mit Frischhaltefoie probiert?
@MarkoRoolaid 19 сағат бұрын
Ursprünglich hatte ich vor, es mit Frischhaltefolie zu machen. Es ist wahrscheinlich machbar, aber es ist sehr schwierig, faltenfrei zu werden. Mit Laminierfolie erschien mir dieser Vorgang viel einfacher und das Ergebnis war für mich viel besser
@Paulkurth 3 күн бұрын
print the air frame in your favorite color, then the lack of color on the covering won't seem as bad. I actually like the clear. It gives more opportunities for interior lighting.
@MarkoRoolaid 2 күн бұрын
ok, thank you
@nevillecreativitymentor 4 күн бұрын
huh? so you cover only one side !!?
@MarkoRoolaid 4 күн бұрын
@@nevillecreativitymentor yees
@artxxyy 5 күн бұрын
Qual motor e esc você utiliza?
@MarkoRoolaid 4 күн бұрын
hi link here kzbin.info/www/bejne/baTIoWmbZqyHkKssi=35g9_2vr_rgMjQFb&t=423
@timothyknight2236 5 күн бұрын
That's repairable. Beautiful model - sorry for your loss................
@CyclingMikey 5 күн бұрын
That's a very nice build! Respect!
@MarkoRoolaid 5 күн бұрын
Thank you
@CyclingMikey 5 күн бұрын
@@MarkoRoolaid I fly usually F3K and F5J gliders; I have 3 x Eternity F5J at FAI Light, Light, and Performance strengths and weights.
@subuktageenfarooqi5712 6 күн бұрын
Marko what is the double glue combination you use, liquid & aerosol ?
@MarkoRoolaid 6 күн бұрын
@@subuktageenfarooqi5712 hi, link here www.rotorama.com/product/power-fix-ca-pack-vterinove-lepidlo-r-s-h-20g-aktivator
@LorenzoPenna-s6y 6 күн бұрын
Hi marko can you write the measurements of the carbon components?
@zdog90210 Күн бұрын
What I was able to determine from the CAD model is that you need six 3 mm carbon rods for the wing two 2 mm carbon rods for the push rods The front two servos to the rear control surfaces and then 1.5 mm carbon rods for the front electronics bulkhead and attaching of the rear tail pieces
@zdog90210 Күн бұрын
The 3 mm carbon rods should be 1,000 mm long
@jamesatkinson7517 6 күн бұрын
Be better without the music the sound of brushless motors is music enough
@angryflite 8 күн бұрын
What type of filament did you use to build this model?
@MarkoRoolaid 6 күн бұрын
hi, bambu lab Pla aero
@angryflite 5 күн бұрын
@@MarkoRoolaid Thanks!
@JIACHENWEI-b6t 8 күн бұрын
I have a problem, during my construction of the wing, the length of the carbon fiber tube was not found in the video🥺
@MarkoRoolaid 8 күн бұрын
@@JIACHENWEI-b6t Hi, ok. 36/34 1500mm, But they need to be cut a bit shorter afterwards
@JIACHENWEI-b6t 8 күн бұрын
@@MarkoRoolaid I believe that with your help, my work can be completed faster，from China
@bobloch 8 күн бұрын
Really good solution for the battery 😃
@mustafaylmazbaysal9573 9 күн бұрын
merhaba Boş durmayan yeniliklerin peşinde olmandan dolayı tebrik ederim. Ne demişler çalışan demir ışıldar.
@MarkoRoolaid 9 күн бұрын
Çok teşekkür ederim, daha önce hiç kimse Türkiye hakkında en azından Türkçe yorum yapmamıştı. Sizi Estonya'dan selamlıyorum
@irvingcuevas6689 10 күн бұрын
Hola Marko, de verdad que tus videos me encantan, actualmente estoy estudiando Ing. aeronáutica y tengo un proyecto de un planeador, en América no puedo encontrar el tubo de fibra de carbón que usas al menos todo es recto, tendrás el numero de parte para mandarlo a pedir a Europa? Saludos.
@SILVIOFRANCO1 10 күн бұрын
Awesome. Take my money. Where are the plans!!
@MarkoRoolaid 10 күн бұрын
@@SILVIOFRANCO1 😃😃😃👌 All my plans are here grabcad.com/marko.roolaid-1/models
@waynephillips8730 10 күн бұрын
Very nice, but I'm not joining grabcad to download files.
@Jhnny5 11 күн бұрын
Another technique to master! Thanks for show it to us!
@rcdavidk 11 күн бұрын
Excellent Cub... nicely done... and thank you for the files. I have a P1S, no carbon for me. Could the carbon parts be printed in PLA? PETG? Would it be possible for you to post a couple of part weights? Maybe a fuselage or 2, a rib, a tail section or 2, landing gear, ski? Then I'll know I'm within range. For example, is Fus1 48g? Fus2 12g? Landing Gear 37g in CF? Landing Gear in PLA is 44g. PLA is heaver that CF?? And finally... do I see 5 1000mm x 3mm tubes and 2 cut 3mm tubes? 6 3mm tubes needed? and 2 1000mm x 1.5mm rods? Thanks.
@ripmax333 11 күн бұрын
The Hot Laminating film is an Interesting Solution but at @8:35 you set the Iron at about 115 degrees am I right or I'm seeing it wrong? How the PLA Didn't deform at the touch of the Covering Iron?
@MarkoRoolaid 10 күн бұрын
Everything you see in the video is correct. Hot laminated film needs this heat. If you heat it for a long time, PLA AERO will definitely deform. But actually it is very easy to install, no need to worry about the temperature
@phgi3593 11 күн бұрын
learn a lot in video😊
@zdog90210 12 күн бұрын
Thank you for this project! I am gathering materials and am stuck on the carbon rods and what i need, 11:18 do I need six 3mm diameter 1000mm long rods and then a few 1.5 mm rods for stabilizers and electronics frame. Also if any one id wondering the tool being used at 8:35 to iron on the laminate sheet is a "Sealing Iron" that should give you results on AliExpress/Amazon/Ebay
@moamlkhalid 13 күн бұрын
0:28 name app ?
@canonballsimp 13 күн бұрын
I don't know whats better, the song or the plane!
@alexherrera3918 13 күн бұрын
LOVE IT!! i hope you can consider share the plans. tks!!
@MarkoRoolaid 12 күн бұрын
Hi, all my drawings are here grabcad.com/marko.roolaid-1/models
@SteffenMünch 13 күн бұрын
Great work Like ever, Marko. Which Brand is your Mini electric screwdriver ?
@MarkoRoolaid 13 күн бұрын
Hi, Miniware
@SteffenMünch 13 күн бұрын
@ thanks
@Rob1970s 13 күн бұрын
It's like watching a white cat in a snowstorm !!! I couldn't see F all . First I couldn't stand the music.. then you don't speak English... Then I'm trying see this thing flying .. but couldn't see F all so no sub from me today...
@EMTAx 8 күн бұрын
Maybe you need new eyes? I can see everything perfectly🤔
@Rob1970s 8 күн бұрын
@EMTAx enjoy u 🤡
@Plottershik 13 күн бұрын
мы такое и з потолочки руками режем 20 лет
@fgroen1225 13 күн бұрын
your smile at the end says it all. :) Cool project!
@MarkoRoolaid 13 күн бұрын
@@fgroen1225 😊😊😊 Thank you
@ripmax333 13 күн бұрын
Those ribs are LW-PLA? How did you managed to use Iron on film on them?
@MarkoRoolaid 13 күн бұрын
Hi, Watch the long video, everything is explained there
@rcforall4842 13 күн бұрын
Nice i know it's late but is there vector thrust for motor mount?
@MarkoRoolaid 13 күн бұрын
@@rcforall4842 Hello, I have used the same angle as on the wing, i.e. parallel to the wing
@rcforall4842 13 күн бұрын
@MarkoRoolaid thank you very much for your Fast reply realy appreciate i watch all your projects it's realy and Amazing skills and Artwork.
@iammeobviously6815 13 күн бұрын
I'm pretty sure Ive heard this song in a flight sim before... Which one was it?
@MarkoRoolaid 13 күн бұрын
@@iammeobviously6815 Hi, song-Creedence Clearwater Revival - Fortunate Son
@iammeobviously6815 13 күн бұрын
@MarkoRoolaid oh, I worded it wrong lol. I meant which flight simulator it was