Bought additional sand paper set from Amazon. Tested the 400grit and paper seems loose. I’m sanding glass bottles. The glass jumps and bumps. Paper is tight and balanced. I wonder if it is thinner paper causing this. Disappointing as I need to use grit up to 1000. Any ideas will be appreciated.

Enjoyed the video and assembly. Very nice well lit shop and that lathe tool holder with the sloped floor/rest is very interesting - i plan to build one like that soon.

what type of drill bit did you use to make screws go deep into wood

Great Job! Do you have plans available for this build?

You can actually adjust the in feed and out feed tables to eliminate all the snipe.

What’s the longest workpiece you would recommend using with this jointer?

Can the loud crap music, it BLASTS when it starts and always requires a volume reduction. Still don't understand why folks think this is so cool!!!

Cool! I am buying an 18, and hopefully for under $2000. Is that a good price, assuming it’s in good condition? What makes one a master turner? Is it in years turning , proof of craft?

Very useful info 💯 👍

I have the same jointer and planer. Theyre great. Need new blades on jointer though. i think i hit a nail and now it leaves a ling down the middle of every board.

Great review! Thank you! Keep ‘em coming.

Your 2x4 look very nice. Usually i get full of knots and not straight at all.

Good job and project thx for sharing

Great video...thank you for taking the time...I was disappointed to see that Lee was not wearing a face shield. Safety. Job 1

What angle would I need to get 3 4x4s to make a tripod for hanging a staghorn fern

A great vid. Now for a few foot rests!

I love the project please if you can send me dimensions for chair end sofa .l wish to build this summer thank you Chris

What color is the stain, it’s beautiful!!

I’ve had this lathe for a couple of years, and I’m very disappointed. The starter switch and relay have gone out several times. It’s been a chronic problem, and although they haven’t corrected the defect, once the warranty expired, they wouldn’t replace the part on their dime. The tech person told me it was the switch, so I bought that and installed it but it ended up being the relay causing twice as much downtime and I spent twice as much to fix the problem. I don’t however know how long the fix will last. The kicker was, when I politely…yes, politely…insisted that good customer service would be that they replace the part for free, the Tech Support… read “customer service”!… person hung up on me! Also, the indexing feature is horrible. When you back off the pin that indexes the wheel, it’s loose and tends to wiggle free and ends up on the floor. If you twist it in too far it rattles the plate and probably will eventually affect that part too. We have a Laguna lathe, a smaller model, at the woodturning school that I teach at, and we’ve had nothing but problems with that item too. It’s your choice what you buy, but I think there are a lot of that are options out there. Good luck!

👍👏

Great job

just got mine. what model ridgid vac will fit the dust port? thanks

Is it 110 volt or 220 model

Классные стулья -кресла. Вы молодец!!!

Love mine ,use it all the time ,never no problem

Can you put a description of what stain colour you used? I love that colour and would like to pick the same one.

I own this model, and after a month, I have discovered the motor get clogged with dust because it's not a sealed motor. It starts to turn hard and shuts off. I have remove bottom cover and vacuum it out and turn it manually to get it to turn on again. Not a good design since using the 6 inch disc causes the majority of the dust to infiltrate the motor. FYI Buy at your own risk...

Seat Base 2x4x26 not 29

You do have any plane and material

Thank you for this review, tremendously

i wish you would give dimensions, i want to follow your version with the slanted back.

Really love this design. I would like to built these to go with my pallet sofa. Are the dimensions listed for one chair or two? I am asking because of the (2) 2x4x33 and (2) 2x4x26 dimensions. I am new to woodworking so I wanted to make sure I was cutting the right amount.😁 Also how many 2x4s did you buy?

drywall screws??

i won't lie that square angle shot gave me a boner.

Can you tell me, how much adjusting did you have to do out of the box? Table levelling? Not too worried about the back support, more the in table/out table

Love it. It is the easiest one I have seen so far. I wish you'd make the cushions another color, but I know that is not the point in this video. Just could not skip😄

Have you had any issues with the fence

Great job! I just wish I had seen this video before i bought a Grizzly jointer that has all of the level set screws in the top of the infeed/outfeed tables. I maybe should have left them alone, but they recommend spending an hour calibrating the tables. It's now been more than four and I'm ready to send this thing back. I've noticed that some benchtop jointers like the Wen you bought have the infeed/outfeed tables basically preset and ready to go out of the box. You're right. It is a home run if all you need to do is check the fence a bit. Craftsman, Grizzly, and some other benchtop jointers have this design which I think is flawed. Thanks for making this video. I was trying to guess your accent and location and I want to say New Jersey or northern Maryland.

Do you still love this jointer? Looking to do small signs, so I think it would be perfect.

I like you snder

Thnx for the video. .. shopping for a belt disk sander ...leaning towards this one you have ...I've priced this model.... around $123.00 at home Depot right now ...merry Christmas

I am having trouble lowering my Wen planer below 1 3/8", have you run into that problem?

Do you use the Wolverine on the 8" grinder to sharpen your non carbide tools? If not, how do you get the grinds/angles/ Good vie.

Does it come with extra sand paper?

I'm sure you've discovered it by now, but in your video, the riving knife is not in the correct position, which is why the blade guard looks weird.

Nice video. How heavy is the headstock? Can one person wrastle it on and off? I'm sure you removed that and the tailstock before you moved it to its final position. I know Laguna has a mobile base for it too, if it had to move around a lot. But that might cost enough you'd need to wait on the Tesla :^)

How is it holding up? Still recommend it? Been debating on getting the 8” with extendable table.

Any luck on finding a second “bed” for the belt sander? Great video, thanks for posting.

Do you have a link to the cushions that you used?

Now that you have had this saw for a few months, how is working? any problems?... looking at this one or the DeWalt one like this... what do you think?