I’m building a brigs 22hp v twin and I’m not sure how to set up the foot pedal for throttle. It’s a speed way motors petal. But can you show me how you do the throttle assembly for racing.

How much does one cost

You can take a spare cut to length or stock pushrod, cut a couple inches off it, cut it in half and then thread each half, use a piece of allthread and two nuts and make an on the spot adjustable pushrod to measure. Idea for next time.

What sprockets and chain did you use

You are my favorite KZbinr. Keep up the good work

EC Carburetors sold those in the past, but theyve been out of stock for at least a year. If you were to sell those supports i would buy a few.

Hi! What could be wrong with the Peerles 700 5 speed When the machine is running, it doesn't go overboard and shake the gear stick What could be wrong and where can I get parts ordered in Finland?

Tubes are better in my opinion lower air pressure can be run if necessary. Which tires do you think grip better saver or master?

Where can I find a transmission I bought a mower that had the live axel swap but did not have the transmission

Like everyone has an engine hoist.

Loving the detail, mate. Thanks for a very cool series 👍🏻🫶

Do you know where you got the parts for that motor

Following!

Wow well done

Do you any extra one of those I need one for my racing mower

ANYONE know what type of engine this is please help

Can you give the part number for the oil seal you need to run gear oil please? Thank you!

This is so cool. I've been wanting to raise all my life. Since my first junk car, i would race around the farm .. Now im looking to do something new, and this lawnmower raising, i think, is it.. .looking forward to seeing some races, but not having much luck in finding the raise tracks. Any ideas, i live in Punta Gorda Florida.. Thanks

Can I have the link to but that pulley on the engine

What is the average cost to bild one like this

You read my mind, thanks for showing.

Im about to have to start from scratch to eliminate the old cvt set up and all the brackets that are involved

Where's the update?

Where do u race at?

Any idea how to remove the drive side to replace the spring? I have lost mine. Doesn't appear to be nut on that side.

Wait? So you are making front axles to sell? How much?

I need some help on setting up my mower for racing can you help please

Always a good time when I see one of your videos

I am building a similar chassis and also using the 700 transmission and I'm wondering what you did to make drive sprockets with larger tooth count.

Your videos have been a huge help to me. Your efforts arw greatly appreciated.

Hey man, first off I’ve watch your racing mower build video’s many times, very informative! I’d greatly appreciate if you could answer some questions as I’m very new to the racing mower thing! My son and I are building two racing machines, mine has the Briggs Intek 725cc v-twin like your I believe. What wires on the engine are essential for it to run??? Any photo’s would help. The engine was pulled from a husqvarna mower, and I know some wires aren’t needed! And second, I did remove the governor and I’m a lil stumped on how to hook the throttle up now??? I will be running the throttle off a brake lever like yours. Again any photo’s how you did yours would greatly help? Thanks again Shayne

It's definitely 10 now😢

The real question. How much to go from your garage to mine? Lol. Jk.

What's better for a racing mower the 700s or 820?

Why don't we seen many honda power racing mowers?

Boo!

Dam I wish I seen you video earlier I just ground the crank and lightened the piston and added counter weights to original weights :/ lol those brass slip ons are a lot more safer with revs by the looks

Little late to the show here, i dont run mower circuits as we dont have any here, more so just a group of guys that go out and play, i was told to run tubes but i do not. Also if you put a healthy few shakes of baby powder in the tire and roll it around coat the tube its suppose to prevent it from binding or pinching. Learned that doing dirt bike tires

What size wheels are those and where did you get them

What transmission im gonna build one

Hows the racing going? Id love to see an update video

I know its an old video, but what angle do you have the plate that holds the heim joints to the axle?

That piece of aluminum is a rain gutter nail with the head cut off.

For the peerless transmission the input shaft has splines. I tried searching for a 12 tooth sprocket with splines but none that I could find that would support a #40 chain. Where did you get yours from? ty

Where do you get that intake manifold?

I thought about makeing a full one out of aluminum and TIG welding for my Kart. But the time and cost just didn't make sense when i just bought the plastic cover for 35USD.

why intek 23 versus vanguard 23 ?

the spindle broke because its moly. unless you tig weld it they become brittle and crack. we use a regular grade 8 bolt on our outlaw mini mod cars that are 900# and use a 600 crotch rocket engine

Any of your used parts for sale ?

There are no oil seals because the trans is made to use grease, not oil.The seal that was there was installed to keep water and dirt out.