Junk them lr44 batteries don’t last and hard to find

Junk them lr44 batteries don’t last and hard to find

awesome!!!

That old bearing was dried out.. Grease them every 800 miles or so and they'll last a long time.

ступицу слегка нагреваеш а подшибник ложиш в морозильную камеру и он спокойно ложится в ступицу и не надо колотить

I learned something from your video .Thank you . I have to replace a hub that broke on my 08 RZR. I think the bearing is still good but I now know how to try this without a press. Thanks for all the good info.

I upgraded my 2008 rzr to a 2022 pro xp and I was in a hurry to take it to the trails..So I bought the polaris brand aluminum roof and flip up windshield..$$$ but my rear storage boxes (same as yours) I got from amazon and my door and center storage bags from amazon too.. I bought 32" tires on beadlock rims from Rocky mountain atv for $1200 on sale.. 🙂 and a rear windshield from the same company that i like a lot.. All my extra lighting was from either ebay or amazon...what a money pit lol It really needs the gearing changed for the 32" tires for rock crawling..It's geared high from the factory..

Nice to see you back on KZbin Travis Like your lift. I might have to make me one.

I have a question and prolly nobody but me wants to do this but I have a 2012 RZR 800 (60” wide) and I want to convert it down to a trail version (50” wide) so I can ride on 50” trails in the forest. Is that possible?

Hi Travis 🙂

I have a 13 rzr800 4 seater. She doesn’t turn left that good. Is that from maybe the previous owners work and it not being centered ?

Thank ya for sharing. Replacing the ball joints on my 08 800 and this gave me the information I needed.

put that bearing in the freezer for 2-3 hours or more determine your direction so you know what way it goes in when you remove it from freezer.. use a heat gun and heat the hub up pretty hot 220-250, drop freezing bearing in soon as you pull heat away drop bearing there and it will drop right in, heat it up right next to freezer so it comes out of freezer same motion you remove heat.. use a heat gun or blow dryer so hub is not defaced in any way at all .. drops right in . .

Hello, Are you interested in testing our products? We would like to invite you to test the Soft Upper Doors for your Polaris RZR PRO XP

With the hair, the hole in the crotch and the incessant coughing/wheezing, I pretty much stayed moist the whole video!!!

wow thanks show hard work on video youtube smile ...

What kind of snorkels do you have? Do you recommend them? Is there an installation video?

Great video - any thoughts on the grease that's being used would be appreciated. I'm going over my '08 500 Sportsman and relubing/inspecting the cv joints. I was going to use the preloaded packets of generic cv joint grease but was wondering if thats a good quality grease and if they contain a sufficient volume. I gotta say I love the way buddy is packing the balls, cage and races though - thanks again

I can’t get the joint over the snap ring

I know this is an old video. It looked like those rear lower control arms bolted right up. Most of them super atv kits say Rzrs or 800-4 only. So they appear to fit just fine.

Is this super atv a arms??? And will ANY rzr 800 ball joint fit these arms???

Good stuff thank you sir.

Gi

Great info appreciated....was wondering why you didn't grease or pack the bering with grease before it was put back together....?

Smart easy way, used old method like you been for years. Saved me a lot of money 💰👍 Old school methods saves a lot of money.

Where do i get the bearing ccage and 6 balls for the inboard drivers ssteering c_v my cage wabroken at 2000 mi my rzr is 2008 wit 2k mi .stored 4 13 yrs. Good luck.

How can i tell if i have a rzr s conversion on my 2008 rzr ?

I need one with the 700

Wish you showed more of the preload set up and where you was measuring from.

Are you interested in testing products? We would like to invite you to test the center storage bag for your Polaris RZR Pro XP

How have they held up??

❤Have any plans for bigger tires? Im itching to get 32's and clearence arms

Put bearings in freezer. Use a propane torch on housing and cold bearings pretty much drop right in.

Thanks

I bought a 2010 RZR 800 50" for $3,500 and found the ride a little rough. Started researching converting to S and you have the only vids out there on that process...thank you! Price on that conversion with all new parts is now over $2,700. May be a project for this spring.

Hi there, just found you guys! Love the vids. Looking forward to seeing more 😀

When installing new bearings I use a 2x4 to take the damage.

Best cv boot replacement video, don't know why it doesn't have more views. Knocking that ball bearing housing off the end saved me, I was stumped on how to get that thing off.

Do i have to greases the bearing? Someone told me it was sealed

I noticed you got yours mounted on the Top rail of the trailer not the lower rail, your not compressing the suspension as much as you would if it was on the lower rail wouldn't it be more secure to be lower ? just a thought, /question? your thoughts on it?

You guys need to do a repeat of this as a 20 year reunion!! I’ll take the videos this time so y’all can ride together!

Thanks for show us how without bench press!!! I noticed other video they use grease tool on hub to press more grease inside, not see you do that?

Thanks for the idea cept I use flame 🔥 on the aluminum & stick the bear'in in the freezer..... speed safe

Thanks Travis you saved me from having to find a video on cv boot replacement. Good video. 👍👍

That's one awesome trail for your upcoming video.

Looking forward to seeing some riding videos with that new machine 👍 Glad to see you posting videos again 😀

🏆🏆🏆👍🇺🇲🙏 Thank you for sharing.

This is a fab video

Great

Mang you as hillbilly as it gets 😆 🤣