and my #1 reason for wanting it to boot to single game - I want the attract mode for that game. I sure wish you could just run the normal menu with all games available, and it just be that once you select a game, it STAYS in that game mode until you TELL IT to go back to the menu. But nope, it just doesn't work like that. Great video explaining how to do single game mode!

Thanks for the detailed info

whew finally got wifi to work!

Recommend adding a step. The sprayer nozzle needs to be protected from crushing by the puller. Either pull the nozzle out first or better, put the nut back on backward for a few threads so the puller can push on metal to metal.

Great video! Can you also please tell me how to add the short pre-videos when you scroll through the games?

Excellent Video!!

I used your video to figure out the white rubber placement on the left side. Thanks.

you need a better soldering iron, not getting hot enough.

Hey put a 12 inch crescent wrench to hold flywheel on end of puller

I need help with my 60 in 1 cocktail table arcade. I have a checked board screen. I don't know how to get the screen to work. Please let me know how to fix it

Great video

All of my games are OFF except for Pacman. There's nothing i can do to turn them ON. I have an upright Pacman arcade with a regular joystick and 1P and 2P Start buttons. No trackball.

I would suggest some anti-seize on the motor arm splines too...

I know this is old but i was just fixing mine and dropped the nub and can't find it. Is there somewhere i could find one to buy? Thanks.

Can you please post where you found this, been wanting 1 My Centipede needs a new track ball too I been wanting to have bowling m in too Spinner will work for that too

What sucks the older version of Rampage it did come like that you have but IT WAS 4 PLAYER

Drive shaft vs crankshaft? Might research

Sometimes....i use carburetor cleaner untill it runs out of the bottem of the shaft, then soak it with P.B. until it starts to run out. They seem to resist less when i do this

Had to leave after the third time of that same CH music clip.

Thank you great job. Thank you

Glue a small magnet in your plastic cup. Simple is, simple does. When not if, you knock over the cup, they don't go every where and cant find 1 of them and stop everything in the tracks over 1 nut or bolt. 🙄🤔

is there somewhere i can get this now??? i cant fine it anywhere

The video was great, then you ruined it with your poor taste in noise some call music. Sorry 1 dislike headed your way.

the wedsite not working OK?

It's fun watching someone do things like this who aren't mechanically inclined.

Doing a great job explaining step be step, one thing,it's not a driveshaft it's the crankshaft, but otherwise great job!

Just so you know, bud, OL does not mean "point zero L"😃 . It means "over limit". IE the resistance is infinity or out of range if you are using the wrong range setting to give a correct measurement

Great Video... thanks so much for sharing👍

I thought you said you was going to cover 2 methods of how to repair this

When he says reboot does he mean turn it off then back on or is there a reboot button I don't know about? I keep losing the changes I made in settings when I turn it off and back on

Every time I reboot, I lose all the settings I just changed. Does anyone know why?

Good work, noting more to be worry abouth, Good tool its more than 50% of all the work..😉

must be a common thing, just noticed mine was broken off

Way too much talk about doing the job and not enough doing. It would have been much more helpful if you replaced the arm.

I have the same lawn mower as you. Can you tell me what pto clutch part number is so I can the right one. thank you

Hi everybody! Can anyone here help me? This link has no more downloads (MR BURNS 8GB Image - 800-in-1 Vertical Classisics RetroPie Image ). I once have downloaded this image, but lost it somehow. Can anyon here send it to me? Many thanks in advance!

Grat example how nice you covered every step into detail! Great job😊

I squirt any of mine with oil or pour some old oil on then smack the flywheel nut with a hammer to break any rust seals around it spray again with oil then unscrew

Stator

drive shaft lmao

This seems to be a very common issue with the Wranglers. Mine needs a fix up job too, so thanks for this how-to! I guess the robot that sticks these on during assembly either needs an overhaul, or maybe a whole new set of instructions on how to do it right. 😁

Oh my Lord!!! Thank you!

Scott, is it possible to keep the on/off Arcade1Up switch as-is on the control panel? Or with this mod do you need to move it to the back or is that just preference? Same question for the volume button?

any updates?

No more arcade videos?

How do I get the 5/8 bolt holding pto on loose. When I try to loosen it w ratchet engine turns over.

Thank you

Great video..

Dumb questions if you have a 60 and 1 does it automatically default into vertical mode on a wide screen monitor?

WHAT? Nuts are bolts and bolts are nuts?? I'm confused.