If the device wasn't submerged or dropped, there are a number of possible causes, including clogging with debris, a broken wire, a faulty circuit board, or a worn-out battery. If you don't have experience in repairs, it's best to have a repair professional check it.

great.

Purchased on Aliexpress. Prices vary depending on whether or not the connector and sensor are included. There is no model number. Search words: "xf1" "cable".

@@orientalbored thank you so much

お役に立てて何よりです。

When the lens retracts, the notch on the tip of the lens presses against the protrusion on the inside of the lens barrier, closing it. When the lens extends, the notch is released and the barrier is opened by the force of the spring. All models have roughly the same mechanism.

残念。当該商品の説明書きを参考にしてください。

If the sensor is a CMOS, check to see if the focus is correct. If it's not, you'll need to adjust it, but if it is, there's no need to. Just tighten the screws back in place.

It depends on the performance of the conductive adhesive. Generally, it is weak against impacts. Cheap ones made in China cannot secure parts in place. Depending on the number of shots taken, the cable can last for about two years if replaced properly. As for the durability of the cable, it can't be helped as the lens design has some problems with the structure. I hope you don't destroy or lose the sensor.

@@orientalbored Yesterday I spent half the night sorting out the lens. I couldn't resolder the sensors, it's not for my eyes. The camera works with the stabilization turned off (in A mode, that's all I need). Thanks again, without the video I would definitely have gotten lost.

結果としては、主要部品交換で「こんなに反応が変わるんだ」と快適になったので良かった気もしますけどね。

I'm not a repairman. It's a hobby.

@@orientalboredwould you consider trying to fix mine if I sent it too you and paid you? Cheers mark

@@markridings7629 Please find a repair shop in your country yourself.

慌てずゆっくりと着実に回すのがコツだと思います。

持ち手は、確かにああいう丸っこいタイプの方が力が入りやすい気がします。標準の物だと手の平が痛くなります。 そして、当方は、右ネジを左ネジだと信じて頑張りすぎて刃先が割れビットだけ2本目購入に突入中・・・

My pleasure.

If the cable comes with a connector, sensor and thermistor, only the motor part needs to be soldered. If the cable does not have the sensor, connector, and thermistor attached, you will need to replace them all. Be careful when purchasing cables. It is safer to use a tester or similar to check in advance whether the cable is truly damaged. In rare cases, the image stabilization cable or focus cable may be the cause. It's best to identify where the problem is first.

@@orientalbored thanks a LOT for the detailed explanation!

@@orientalbored Friend today I opened the camera and took a close look at the cable. It seems to be in good condition, it is bent right there like yours but no clear breakage. You mentioned the image stabilization cable, which one is that? And what else could be the problem? Mine turns on and gives me the turn on and off error right away, the lens do not come out :(

@@ericpena3426 You cannot tell if the cable is broken unless you measure the resistance with a tester. There are various possible causes, such as lens deformation or dirt on the gears, so we cannot point out the cause here. You will have to investigate it yourself.

My pleasure.

i don't know.

拡大鏡を使いながらFFCのライン上のみをカッターなどで削るという方法もあります。コネクタにもよりますが差し込む厚さが大丈夫なら大丈夫だと思います。Amazonなどで同じピン数を購入してきっぱりあきらめるのも・・・

@@orientalbored アドバイスありがとうございます！ 予備のケーブルも買いつつ、もう少しやってみます。熱湯に浸けてからカッターでしごいてみたら途中まではいい感じにできたのですが後半線まで切っちゃいました（笑）落ち着いてやればできるかもです。

拡大鏡も買ってみようと思います

温度が高すぎます。ドライヤーの先をもう少し離して様子を見ながら作業すると良いです。剥がれないからとせっかちになると修理はできません。

FPCの素材も銅もハンダ小手の温度程度では、溶けません。(注：FFCは、被覆溶けます。また、 バイパスする銅線の被覆種類により被覆のみが溶けるのと溶けないのがあります。) はんだ付する時に温度が上がりすぎるとハンダがぼそぼそになって濡れ性が悪くなるので資金に余裕があるなら温度調節できるハンダこてが無難だと思います。技術次第。 今後どの位使用するかによっては、ステーションも良いのかもしれませんが当方は、使用していません。 ハンダこて先、フラックス、手を離せる拡大鏡、ピンセット等他にもお金かかるので総費用を良く考えた方が良いと思います。 ハンダ作業初めての場合は、良く調べた方が良いです。

通常グリンって回したくなりますが扱いが難しい工具です。

If the photos are recorded on the SD card without any problems, the LCD may be defective. 1. Try reseating the LCD cable. (Check if the LCD itself is defective or the backlight is defective.) 2. Inquiries regarding manufacturer repairs. 3. Purchase a compatible LCD on eBay etc. and replace it yourself. (Please note whether a backlight is included) 4. Give up and buy another model.

お役に立てて良かったです。

Discharging the power of the strobe capacitor.

販売価格の縛りが低すぎるんでしょうね。

Even if you turn on the power with the LCD cable connected and touch it lightly, there is no display. Check: Re-insert the LCD cable and check if it is inserted too shallow, the connector pin is damaged, or the LCD cable is damaged.

自分もカッチ、コッチと音がしないなら1秒刻みの方が時計らしいし見やすいと思います。

aliexpress or ebay. Please be careful as there are different types such as those with connectors, those with sensors, and those with cable only.

楽しんでもらえたのなら何よりです。

汚いから軽くやりましたがそうなんですね。

@@orientalbored 黒いのはカーボンブラシ由来のカーボンで これは良い状態です

@@nishimurat.1254 なるほど。

I'm not sure where the capacitor is, but if it's a flash capacitor, it's next to the lens. The side without the board.

参考にします。

If there is no submergence or fall, most likely it will be a disconnection like the one shown in this video. It seems that if there is slight contact when the lens is expanding or contracting, it will not cause a lens error. It is better to replace this cable slowly and carefully as it is difficult to know which direction to crease the FPC cable when reassembling the camera shake unit. It is a good idea to keep the original cable you removed and use it as a reference. After that, you will not be able to use the minimum or maximum focal length unless you properly align the gears on the CMOS bottom plate. If it does not fit, please experiment with engaging the gears with the lens extended or retracted when reassembling. I wish you success.

#000 or #00 or #0. Since there are several types, it is impossible to answer with this information alone. Look up other people's KZbin videos on how to remove the broken screws.

@@orientalbored thanks

​@@orientalbored I already Fixed the Problem But I accidentally torn 3 Flexi Cables On The lens😢

​@@orientalbored I Already Fixed The problem But Accidentally Torn 3 flexi Cable On The lens😢

What was that? Was that a question with me in mind? This video is not a repair method, but a work record.

Ok sorry I was in hurry so I didn't read the caption I thought your video will resolve my problem. But its okay 👍

Since the Japanese manufacturer's sensor is a discontinued product, I don't think you can get the same one. I couldn't find it myself. Sometimes cables with sensors are sold, so why not wait for that?

Nail is claw or hook.sry.

Indeed.

aliexpressという海外通販サイトです。 先ほど少し検索したところそのものずばりは、無くなっていました。 「encoder strip canon g6030」でGoogle検索してaliexpressが出てきます。「QC6-4592」自体は、あっていると思うのですが・・・

ご返信ありがとうございます。 英語が苦手なので購入できるかちょっと不安ですがあたってみます。 ご親切にありがとうございます。ｍ(_ _)m

@@user-ll2qo1rl8m 店舗が結構いい加減な場合があるので本当に使用可能なのかどうか確認してから購入した方が良いです。そして国際郵便で配達に1か月前後必要だったりもします。 また、汚れが裏面(黒線の印刷が無い方)でしたらコンパウンドや1000番以上の耐水ペーパーで表面のみ軽く削り取るという方法も。表面の場合は、拡大鏡とまち針で汚れの透明部分のみ軽く削るとか手先が器用でしたら方法がなくもないです。 黒と透明の間隔が同じならアマゾンにある他機種の物でもよいのでしょうけどねぇ。

貴重なアドバイスありがとうございます。 あれからこの動画を参考にして分解しエンコーダーをアルコールで浸したティッシュで何度も拭いてみたのですがやはりインクは落ちませんでした。 もう一度分解してアドバイスして頂いたやり方でもう一度トライしてみます。 どこの誰かもわからない私の為にこの様な貴重なアドバイスをしてくださって本当にありがとう御座います。

あれから3年経過していますがまだ快調です。ダイソンは3年で修理不能だったのに・・・。

ハンダ付けするシーンがはんだフラックスで綿棒シーンは、無水アルコールです。

お返事ありがとうございます。がんばってみます。@@orientalbored

All youtube library.

普通の人はそれが一番♪

I'm glad it's helpful.

I'll change it soon.

When disassembling, record the locations of screws and parts. Make it possible to confirm by taking photos or videos. Check the cables when removing the back body. Don't hurry while working. The main board, the top board of the battery box, and the left board are connected by soldering, so you need a technique to cleanly remove the solder with a solder wick. There is a flash capacitor behind the shutter button, so be careful not to get an electric shock. To remove the battery contact at the back, remove the strobe capacitor wiring. [[Be very careful about electric shock. ]] If possible, discharge the strobe capacitor with a 1kΩ/1W resistor before starting work. Gently rub the contacts with a flat head screwdriver to see if any rust is removed. If that is not possible, lightly sand the surface with 1000 grit or higher sandpaper. To replace the damaged part of the contact, cut a thin stainless steel plate or other springy metal plate and process it carefully. Consider whether there are any other personal items that can be used.

Thanks a lot for the reply . I’ll need to get the right tools and get organised. I’ve disassembled iPhones before so applying the same process. I’ll keep you posted. Enjoy your Xmas day and everyone else who’s reading this today.

I'm glad it was useful.

お役に立てて何よりです。

I have no idea if I don't know what's wrong with your camera. I'm not a psychic.

刃先がかかるまで焦らずにやれば行けると思います。 失敗してもPCのネジなら頭にドリルやヤスリなどで溝を作ってマイナスドライバで回す等いくつか方法が思いつきます。 頭を破壊してスペーサーとネジを交換等も。