Im just starting my journey to professional watchmaker (someday) These videos give me a good idea of who I might wind up working for someday!

@Dimitri what would you have done differently?

Does moving the stud support align the impulse jewel into the middle of the two banking pins?

Per riposizionare la sfera dei minuti cronologici basta fare solo uno scatto di corona due si posizionano le altre dei millesimi e dei secondi 👍

Also, tip for people. I stop the watch before adjusting. I had a friend accidently touch the moving wheel and his hairspring popped out.

Hi thanks for posting this. My SPB143 had a 1.7 ms beat error and was 30 s slow and now it has a 0.2ms beat error and is 3 s fast so happy now with that. It was probably stored in some warehouse for too long as it didn't even come in the right box!

Thank you for this video. My Seiko was with more than 15 minutes ahead per day. Following the instructions from this video I did the adjustment about 4 times. After 5 days from the last adjustment I saw a few small changes. Now I have 2 or 3 seconds plus OR minus in 24 hours. For me it is excellent.

Welcome back. I am always enjoying your videos. Very educative. Thank you.

Thanks

So how expensive will it be to have this serviced?

This is the same movement and everything in my Tissot chronograph.

Thank you so much for this video. I’ve serviced loads of watches but am relatively inexperienced with chronographs so I’ve used your two videos as step by step instructions. The magnification and quality of your videos is so good and I particularly like that you add the part number and which lubricant you’re using at each step. Excellent stuff. I believe you skipped the removal of the coupling gear in this video and I was a little worried I might loose an eccentric screw but I figured it out. 👍🏻

Hello. Great as always. I will try. The special tool you use at 5.50 to remove the driving wheel is a self made?

I’d it possible to send to you? What country are you in

Excellent video

how is it possible to have rust only on the cp and nowhere else?

Where is the serial number on this watch?

What were the tools? The measuring tool?

❤

Glass rimov istumant pl send adreess

what about the gaskets?

Your video was very valuable to me. I'm installing a new glass on a watch with a case very similar to the watch in your video. I noticed that this watch of yours does not have a bezel. Is it common for watches without a bezel or is this watch missing the bezel? I wish you much success on your channel and happiness with your children. Thank you for sharing your knowledge.

Wow just amazing. Liked and subscribed!

In riletto con andicappavo al mala cola

What is/are the screwdriver size(s)? Can you provide a link to buy? Thanks.

Does the stem have to be out if the watch to glue the crown back on?

I wish OEM parts were available for a reasonable price, I was considering servicing my own 861 but these replacement parts together would cost more than the service from Omega themselves.

to get a perfect reading do you need to fully wind the movement before measuring or Half power is enough.

Great tip!

I have this watch and I belonged to my father. Pitched in 1969. It is not currently working and is missing the stem. How do I get in touch?

Так я не понял ,в домашних условиях батарейку не поменять чтоли ?

Hi, great video! I am doing the 7734 myself in a couple of days and wanted to prepare a bit. I have a question though, accoring to the service manual the watch needs moebius 9501(or, special grease for mechanism as they call it) on the hammer and hearts. However, you put 9010, the which is the finest oil instead of the thickest grease. Is there a particular reason you choose this oil over the grease? Kind regards, and thanks again for the great video!

👍

What size should the crystal be, relative to the case opening, if using a tension ring crystal? In your example, it seems like the case maybe had a 31mm opening? So you used a 31.1mm crystal with tension ring (0.1mm oversized to generate tension), or a 31.3mm crystal without tension ring (0.3mm oversized to generate tension)? Is this correct?

Baume and Mercier has never ever compromised on quality, and they use good movements, this one is a great example of that.

I have a Seiko Solar Chronograph that i bought used. I need 2 links for it. Can you give me some information how to find links?

Great to watch! I have some Hamilton 992B Railroad Watches from the latter 1950s. When someone has lever set the time at some point, they have bent slightly sideways the ultra-fine steel tip of the minute hand. Would you attempt the same technique, but just pressing the tip sideways? On one of these watches, the watchmaker has seemingly “repaired” the bent tip by carefully clipping the bent end off. This now means the minute hand looks strange because it can no longer reach the dial’s minute calibration marks… so am looking for a replacement.

GREAT!

A very nice video. May I suggest hacking the movement to stop the movement while adjusting it? To avoid any damage to the balance spring.

A very nice profession! If I could start my life over, just this

When its not a expensive watch you could do it yourself, New basic glass online starts with 2 euro upwards.

Fantastic video! So clear and easy to understand

Excellent explanation. Simple but sound. I put my SPB239 on a timegrapher today, adjusted the beat error and regulated the time. The six positions were extremely different, ranging from -15 to -54 seconds. On average, the watch was at over minus 30 seconds. I saw that the regulator pin was almost completely at the minus setting. I wonder who assembles those watches and regulates them to fully minus, resulting in an extremely bad accuracy. It took me over an hour to fix the problem, now it's on my wrist and we'll see in a few days if I have to re-adjust it again, as the six positions were between +7 and -23.... Thanks again for sharing!

What's the name of the music? Great video by the way

And the secret is? Notes to hobby watchmakers: you don't have to own the spring widner and the barrel closing tool, this could be done by hand rather easily. And the graphite grease is not a must, you can use lithium or in worse case any other thick grease instead. Graphite is like a "historical" thing.

awesome job, but crap watch

Hello, could I just remove the steel caseback to my Speedy and install the see-through caseback, or are there extra parts/pieces required?

Top of the line friend, thank you, how much does the adjustment cost

Hi there Maestro! Your opinion PLEASE! I am planing to buy a simple Tag Heuer Caliber 5 Carrera. Dress Watch! Should I go for Tag of forget about it? How many seconds looses by day and what prob;ems holds !THANK U!

I didn’t see the actual adjustment. I wish it was fully demonstrated