Veyron640

Пікірлер

@ДимитърБалев 24 күн бұрын

Can anyone confirm please? So you basically take the 5 pins singal wires going like: 1pin->4 cylinder, 2pin->3 cylinder, 3pin-> ground, 4pin->2 cylinder, 5pin->1 cylinder, is that correct?

@ДимитърБалев 24 күн бұрын

cause i got a different reference met online which states we should do: 1pin-> 2 cylinder 2pin-> 4 cylinder 3pin-> ground 4pin-> 3 cylinder 5pin-> 1 cylinder so, what is the correct approach?

@VncleEvgene Ай бұрын

@11:33 russian style works but you got to place your fingers in the slots for the OEM tool, push the module a little bit down and then turn counter-clockwise. Overall, good DIY vid. Thank you a bunch for the tutorial

@nabeeljacksonrhoda6480 3 ай бұрын

thanks for this. I actually had the electrical pump already removed so I could see what needs to be done to install in the plastic housing. It just slides in and clips in once seated. Nothing even a non diy'er cant do. But the detailed coverage is good to get a grip of what needs to be done and possible time needed. Also, the fancy tool isnt needed, where "v" indentations are located, there are 2, you'd just need to lodge a flat screwdriver and give it gentle nudges until it loosens up. Then use the hand to turn anti clockwise and it will free itself and you should be able to remove it. Thanks once again.

@ChrisKiddsr 4 ай бұрын

Use the box end it works great don't grind your rench

@peterhilbert6428 5 ай бұрын

Did you have vibration problems after in-stall?

@Veyron640 5 ай бұрын

@@peterhilbert6428 nope. That's why I had to do it So that I didn't have vibrations

@peterhilbert6428 5 ай бұрын

@@Veyron640 thx for your reply. The reason l am asking is that l replaced mine and am having vibration problems which never existed b4. I found in an Audi shop manual that special tool 3139/3 is required to align the shafts. A lot if people talk about using a straight edge to align them but l don't see how this is possible because the diameters on either side of the knuckle are different . Therefore if you use a straight edge they won't be congruent.

@yanispayet6138 17 күн бұрын

@@peterhilbert6428did you solved your problem? Same on mine, bad rotating vibrations after change of bearing carrier…

@peterhilbert6428 17 күн бұрын

@yanispayet6138 Yes, l did. Drove the car from British Columbia to Az. The problem was the centre u-joint. It would only articulate soundly in one direction. I ended having to buy a refirbed OEM Audi original.

@peterhilbert6428 6 ай бұрын

Great video, well explained with creative ideas! Thx

@benjaminmanquepi4682 7 ай бұрын

hi, friend. I changed the thermostat and I realized that the hole inside the cylinder head was clogged with stone or grease. And I left it anyway, my question is, is that why my focus is overheating? How could I clean it?

@phantomtec 8 ай бұрын

consolidate your talking.. yikkess. talks to much.. its headache just listing for 20min.. But, thankyou for the video. Peace

@edwardlutsch8475 10 ай бұрын

the only thing is it’s way more fucked up on the passenger’s side

@стич-ы2д 11 ай бұрын

Шура поет????единственная песня у него нравится

@michaelzolman264 11 ай бұрын

I just did one of them it a joke getting that tool on it to get it out... But then i discovered when installing it would not work that tool...So i line it up into the groove and push down and turn to right slid right in and locked..... You have to push down and turn pops right in ...

@mrbanana2811 Жыл бұрын

Do i need that tool or does it work without it

@grandrockwell447 Жыл бұрын

Fuck you guy too much talk

@delmcclamma8359 2 жыл бұрын

Take the stuff out of the way to get it done

@garystanley6097 2 жыл бұрын

Another video where half the fucking job is done. Utter fucking bollocks. Take this shit down and film an ending.

@youngsav7310 2 жыл бұрын

Where did u get that part at nd what’s the name exactly so I can order it

@josiahwyncott7519 2 жыл бұрын

"I don't know what Ford was thinking (making it plastic)... " I have been thinking something similar recently while I have been trying to repair and replace things on my '02 Focus as well.

@zader253 2 жыл бұрын

My issue is always splitting the thing, I just use any 17mm wrench and use the round end problem free up until it comes to splitting the two halves

@theyaregone 3 жыл бұрын

Вот уровень то попсы был ведь!

@3n3ly7m9 3 жыл бұрын

Its amazing how much more a Leather S4 seat weighs to the cloth "s4" style sport a4 seat that's fully manual (lumbar aswell) and no side airbag. The back fold down seats I can toss in the air compared to the S4 ones.

@jirkasemela7375 3 жыл бұрын

Have you some scheme for this please ?

@Veyron640 3 жыл бұрын

What?

@jirkasemela7375 3 жыл бұрын

@@Veyron640 do you have a plan for that on paper ? I want change coilpacks on my aeb. Thanks

@Veyron640 3 жыл бұрын

@@jirkasemela7375 im sorry, but the reason we make KZbin videos is for that point, not on paper. But I suppose, you can find alot of it "on paper" aka in the forums.

@billyc2572 Жыл бұрын

@@Veyron640 he's asking for a wiring schematic that the kit probably comes with.

@billyc2572 Жыл бұрын

@@Veyron640 yes this is why we make videos but your video is based on your knowledge extracted from an existing wiring diagram/ schematic

@rawz8936 3 жыл бұрын

Is it possible to repair the melted part?

@istvanfarkas3365 3 жыл бұрын

Great video, thanks a lot!

@ПесниподбаянАлександрПлатонов 3 жыл бұрын

Класс!

@caminglis53 3 жыл бұрын

B6 connector 2002-2004

@АлёнаАлёна-ы1л 3 жыл бұрын

Алена 2021 г. Я помню,как ты,Санька,пел эту Рябину без музыки! Как же красиво у тебя тогда получилось,я даже удивилась,все-таки - мальчик,а песня - душевная такая,серьезная !А ты,Саша,молодец! Любую песню споешь ! Будь здоров,счастлив,а удача пусть будет всегда рядом с тобой !

@jacobingram8152 4 жыл бұрын

16:58. You didn't say what tool that was to take the coils off with. Is it a Torx bit, or Allen wrench?

@Veyron640 3 жыл бұрын

apologize, yes. it basically, an allen socket. cant remember what size it was

@mechatron2775 4 жыл бұрын

I have original ignition coils from 1996, they work properly. Never touch the coil system and installation at low temperatures because you will damage them.

@Koastah 4 жыл бұрын

this gave me a diy and a laugh haha thanks man