Prerunnerrrr. JK part out

Seat cushions and backs? I just got a 97 f250 crew cab and I need seats for the front and back. Ya’ll have frame, rails and brackets too? I could use those, but it’s looking like a junkyard will be my best bet

Thank you so much for the help with this tailgate

Do you have to have the battery off in order to release the brake interlock?

Gentlemen.... Fantastic. Acquired my Grandfathers '95 F-150 5.0 four years ago and have been trying to put together a 1000 piece jigsaw puzzle each time a problem surfaces. This overview really puts it into perspective. Thanks very much for spending the time, it helps. Though, I still haven't figured out how to travel back to 1955.

Gold is not magnetic

I'd like that in my 92 150

Hello, I just bought a 1992 f150 5.0 flareside and I’m having 2 problems. First problem,the low pressure valve is not taking refrigerant, but the clutch of the compressor is working. Second problem, the truck stalls only in reverse. I have to feather the gas pedal to reverse. Not sure if these problems are common? Thanks

I wonder if you sell tailgates completely reassemble?❤️👍

Thanks sir!! Very good video! Helped me a lot

Holy moly dude just break the beat of the tire on top of it and then pull it out and replace it and then just pop air in the tire and put it back on its bead for God's sake man make it easy on yourself

What's the best way to find one thru military-government

Do yall have a website? I think that would really step up your game. Start getting the google algorithm on your side!!! Also, do you know where I can get a new motor for the seat? would it be difficult to install a secondary seat motor on passenger side as well?

Does the cable do anything in regards of safety? Or totally cool to remove it?

Truly from the bottom of my heart thank you HOLY SMOKES the most straightforward and definitely safest method I’ve seen thank you

American Ingenuity for the win!

I snapped my valve when I was putting air in it; I'll let the garage do this job.

I'd an idea of having a tyre and rim on the ground under a car and putting screw jacks between to force the bead down I ran it past a mechanic he showed me the press in a workshop I'd also thought sawing through the tyre and reinforcing wire but apparently this can't work even in addition to pry bars you'll inevitably need one video on here drives over 2by4 placed over

Great video guys. I don't have a pneumatic rivet gun. Maybe I can borrow or rent one.

Where can you buy the horizontal glass tracks and the plastic nut inside? I cannot seem to find part numbers!

Why would anyone want to remove this??

Where do I find one chromed

U have any Eddie Bauer trim for the 96 bronco?

Thank you!

I have a 92 Bronco custom.. no armrests on the seats and no middle console.. do I need 40-20-40 cushions or bucket seat cushions..? And.. do you know where to get new seat covers for the whole seat? Love your channel.

anybody ever get killed doing it that way? way too dangerous

Just ordered wish me luck

How to remove a mower tire

Nice!

The same line you had difficulty with, I'm having difficulty with. I'm probably going to order a new sending unit , and just clip the line, disconnect from the other end, and try to remove it then. With better leverage.

Your a joke

Perfect spot for sister's face, LOL🤣

I have an older Subaru Forester and removing the fuel tank was probably as difficult as removing the engine itself. The fuel pump diaper (strainer) kept getting clogged because of all of the rust. I managed to follow your advice without removing the tank by using a paint mixer drill attachment to agitate the acid/water mix. The tank was super clean and it was followed up by a soap and water cleaning after. It flash rusted the next day because I did not let it dry and used ethanol gas for the first refill. To any other viewers that want to try his method, follow it 100%! Thanks for posting this!

Finally, I got the electrical connection disconnected thanks to the recommendation of using blaster on it. Got the big fuel line disconnect. The smaller one is a pitta for sure..

Awesome video and information on the removal and installation processes. I am adding this product and these tools for my truck project.

Excellent information. I appreciate you and the team showing the procedures. I'm kind of curious why you didn't do the "Harpoon" mod on the tank prior to installation. I'm going to your channel now to look for the front tank procedure.

How much ft of material does it require per side?

I guess because my truck seemingly had an aftermarket exhaust, it's not in the way, however... disconnecting that wire harness is my setback at the current moment. I'm pushing the tab the best I can, but it's not budging, I even lifted the tank up a bit to loosen the tension but yeah taking a break, so I don't break it.

Any improved outlook on when we can Order these Seat Backs? I wanna get a reminder on my schedule :-)

This helps,replacing rear leaf spring mounts and fuel tank. Thanks for the video. 👍

Lh kick panel is missing and the is a hole next to the H/L switch. Drivers armrest pad is crushed.... not so mint....I'd say

FOLLOWING THIS ONE CLOSELY!

Do you have any available?

Where the toyota boiz at?

I learned a few things. I was just in there today and scratching my head about a couple of things. Now I know. Thanks for the pace of your video. No wasted time.

Good job soundproofing this Hummer H1 much better

Haha Damn!

Hell yeah! Bronco never giving up

Leaf spring top plate and rear seat bracket

Parts