Great video

I picked up one today for 85 is that good for this it's in pretty good

😊

I do have a question for you , what height if Rod is Best ??? 8, 9, or possibly 10ft. ?

I have one of these and I Love it , going Fishing soon.

I got the okuma salterra 50w 2 speed

If I could find a 60 that cheap I would too

Damn in 8 years late but I paid 130 for mine.

Sir... is it okay to use this type of grease that sprays "Wurth HHS 2000" without removing the rivet inside.... And sir... before using this reel, should we send the lubricant inside.. more full reel Lubricant is also required for its existence...,? It is difficult to find the type of grease (penn grease) required for this in our country. So what is the suitable type of Grease Gage.....please tell me sir....im Sri Lanka...

Want to see dead replacement on the reel thank you

Dood i think mine had a thick spring instead of the bearing and no silver ring around the pinion

*Great reel, **enjoyable.fishing** recommend very smooth and I love that you can change from left hand to right hand so easily. Gave it a 4 on durability because I haven’t had it long enough to rate it. Doing good so far.*

70$ rod ?

Brapa harganya???

Missing the screw that locks the handle nut in place.

any rod recommendation for this reel and could you link the new drag system?

just found a penn senator 4/0 on ebay for 30 dollars, wonder if i should...

i plan my first real shark fishing reel being a senator 6/0 or 9/0, and maybe i can move up to a penn squall 50 vsw.

Great video 😊

Dose penn make the 112h any more

Penn doesn't make the 112h any more

Save the fish. Just because you're a moron doesn't mean the fish should suffer!

*Smooth drag. Amazing durability... Once taken apart it is easily cleaned **pickoy.com/penn-1259871-fishing-reel/** and works like new again. Dropped one in salt water for 30 minutes before finding it. Took it apart and cleaned/oiled/greased it. Still works like new.*

*Smooth drag. Amazing durability... Once taken apart it is easily cleaned **pickoy.com/penn-1259871-fishing-reel/** and works like new again. Dropped one in salt water for 30 minutes before finding it. Took it apart and cleaned/oiled/greased it. Still works like new.*

I prefer hand lines for couch fishing. I've tried the Penn senator shown in this video and a few other reels. Though they are good for the cost, most of what you can catch in your living room doesn't require a reel. but perhaps more important than this is what bait you choose when couch fishing. I like to use Velcro jiggers and custom wound duct tape balls. Some people swear by magnets but you miss out on about 90% of couch game. And I think 300 yards is way too much. I prefer to couch fish with about 5-6 feet of line because more than a few times I've gotten my line snagged on one of the zippers on the coushions and it's easier to just unspool the line and pull it by the lure. And this is why most people really shouldn't pretend they know about couch fishing because they do water fishing- it's TOTALLy DIFFERENT. People who fish in water should stick to water and let the experts show the world what couch fishing is all about.

If you go through the trouble of taking the reel apart to clean it, lube it and put fresh drag washers in it, you at least take it completely apart. You should take the rings off of the side plates, remove any rust, and put a film of grease on them. You should've removed the eccentric and the eccentric spring, clean them and grease them too. I didn't notice if you put a film of grease on the pinion yoke, or the eccentric jack, if you didn't, then you should. Did you remove the retaining ring on the bearing and remove the shield on both sides of each bearing, clean the bearing and then pack the bearings with grease, then reassemble them? Being that that reel is from the '70's or earlier, did you upgrade the drag stack to a 5 washer carbon fiber drag stack and ground flat stainless steel washers? Here is a tip, use Cals universal reel and drag grease on the drag stack for a smoother drag. Did you grease all of the screws? If not, do so. Did you apply a film of grease on the inside of the spools sides? Did you take the clicker apart and clean and grease the clicker spring and tongue and button? I believe that some year models didn't have a clicker. Did you remove the bearing retaining shield and remove the bearing from part # 40-114H? Did you then remove the retaining rings and shields from the bearing, clean it and pack both sides of the bearing with grease? Did you then reassemble the bearing and grease the threads on part 40-114H? In short, if its metal, grease it. Did you apply a film of grease on the main gear? A thin film of grease can be applied to the side plates. Did you apply a thin film of grease to the bridge? Did you remove the gesr sleeve from the brige post and grease it and reassemble it? If you did, then you should show the process in your tutorial. If you didn't, now you know a more complete process. *You may need to fabricate a tool from a wire coat hangar to remove the bearing retaining shield and bearingfrom part 40-114H. Take a 5" to 6" piece of the coat hangar, form a loop on one end (you may need to put a screw driver shaft through the loop and use the screw driver as a handle to pull on), then put a short 90° bend on the opposite end. File the inside flat (don't take too much metal off or you'll have to make another tool). Check to see if the side with the short nub can fit inside the hole and hook under the bearing retaining shield. If it does, then you can remove the bearing retaining shield. I'm just trying to help you tweek your maintainance. Tight lines.

Hi great videos. I need a little assistance. I have a penn 320 gti reel but try as I may I cannot get the lock on the reel to work. The reel spins freely for dwarf and backwards. What can I do?

Do you make the rigs yourself?

I have to replace the clicker side plate. Is that an easy job?

Hi friend thank you very much for the video !!! Helped me a lot !!! Big hug from a friend here from Brazil !!! Congratulations on the videos !!!

how many yards braid

LOL that reel is fucked!

now you need a video on how to put it back!

What size senator is that, and is there any way you can do a size comparison between senators and say a 309?

General rule of lube. Metal to metal contact - grease. The exception is on bearings. Use oil.

Hi, could you let me know what kind of line you use and the measurements. Mono filament or shagged? How many meters of line? Measurement of line 0.45mm? Thanks for the info and good fishing.

I just picked up a pair of the Penn 30s, same as yours, on eBay, for $560 USD, so about the same price. I am on Vancouver Island,and they are going to be my halibut reels. Have not had a chance to use them, but I can tell they are going to work really well. Very well made, I have 100lb braid on both, I figure that should do the trick

A couple of great videos. I just bought a 1970s 12/0 for land based shark fishing in swfl and I'm gonna strip it and re grease everything before I head out

I have 6 squall 30vsw's and 2 50vsw's for my trolling spread. Same internals as the international series reels. I really like them. I've never had any issues

Where can I get replacement drag washers for the 4/0 Senator?

How do you review something that's brand new and you haven't even used yet?

Anyone have any trick to fix a frozen handle knob. Or how to remove the knob you hold to crank? Should be free spinning but very frozen, moves just a little.

Can this reel be used for surf fishing

You can fillet a fish, ANY fish, without all the hacking and gutting.

Hey. Very helpful video. I’m struggling to get mine to free spool. Mines Pinyen is part of the spool. When I flip the leaver it pulls the spool down towards the main gear but it always stays on the gear. I’m not sure how it’s supposed to work. Any advise would be much appreciated.

Gee it is sad but this help me thanks

Do you fish off the pier with this ?

nice guided vedio I service my all 114 and113 reels thank you

@ Florida Fisher - Thanks for the help! - From 352

does it still work ok?