Din vu batta CARBIDE ful soma dink. Areu .500” ding batta go dink ! 🍺🍺🍺

As usual, your skills and sense of humor shine! You deserve far more subscribers.

It's simple but effective. Thanks😘

Are there some trade schools that recommend taking cuts,no deeper than.020 ?

Is it supposed to be the other way round so the ball rolls on the bearing instead of skidding on it?

What is it for?????????

Very nice!!

very good

MASHA.ALLAH.GOOD.WORK

A new idea as always! Thank you! Maybe you can help me understand the purpose of the round bearing? It would seem to me that if most of the motion of the ball bearing is vertical, you would want the round bearing to also be vertical? Instead of wearing the hard faces? Maybe I don’t understand?

O rolamento deveria estar na Vertical , está na horizontal , está sem finalidade .

👏👏👏👏👏👏👏

Toujours très intéressant, merci pour vos idées.

Great work❤❤❤

when you increase feed the chips will break better

Wrong feedrate for insert. It shouldnt be making ribbons at all.

...e complimenti x il tuo bel lavoro,wow.😊😊😊

Bravissimi tutti 😊😊❤❤❤ italy

Que porcaria, tanta máquina legal para fazer uma bailarina idiota dessa, pensei que ia fazer algo notável, esse rasgo poderia ter sido feito em um Esmerilhadeira

Po zobaczeniu sikającego "psa" uznałem, że dalej nie ma sensu oglądać 🤦🏻‍♂️

Thank you very much for your video, i'm just an lathe-hobbist ( from 2006 ) and also use inserts NC3030 as you showed in the video; much of the difference relies on type of steel to be cutted ... "common steel" ( for construction ) is the worst, to my sight of see, better i get with "silver steel". I also use my tool upside down, and opposit direction for the spin ... so i learned parting from u-tube, after so many ... "cracks" ... Operating so, the chips easily fall down ... I hightly do appreciate your style of videos, no music, no words ( often unintellegible cause different languages ) ... you just SHOW WHAT IS IT, very clear. With some indication of your hand and fingers, one can understand if a tool is ok for that work or not ... as in this video ... And finally your silent suggestions to use goggles for eye protection ... very professional ... My best greatings from Italy ... were are you instead from ?

👍sobran las palabras👍

Ese inserto es uno de los mejores rompe virutas. Deverias buscar la velocidad y el abance adecuado para que no salgan esas horribles virutas continuas. Sigue practicando que ya aprenderás con el tiempo

Рассея хуле. інструкцій не читаєм.

Nie za duże te obroty ja daje na 280

Gostei, sem enrolação e sem se quer uma palavra e de uma clareza sólida.

Every schooled tradesman knows about these. What material your using depends on type and speed and feed are given by tip manufacturer.

❤❤❤

Sei bravissimo, complimenti

Hast du keine Stimme?

Thank you again for demonstrating so many types! It is great to have that knowledge so we can easily sort through and pick the right inserts for us!

You are doing a wonderful job

❤❤❤

Estes insertos trabalham melhor com fluido de corte e não deve existir nenhuma vibração. O melhor resultado foi o último corte porque é mais próximo da fixação da máquina e teve menor vibração. A ferramenta também pode ser montada invertida (de cabeça para baixo), reduz a vibração de possível folga no eixo principal da máquina e também facilita a saída de cavacos. 😊👍

You can sure tell the difference, thanks for the comparison 😊 !

I didn't notice you use any cutting fluid. Is it unnecessary with carbide?

Great video, thanks for the comparison.

Thanks for the comparison. Were they about the same price, or was one cheaper or more expensive than the rest?

👍👍👍

very good

I've seen a few parting videos but never a side by side comparison of the inserts. I've only recently had luck with parting since I made my own tool holder similar to yours. Previously it was the rocker/lantern style. It's a lathe at work and they won't buy anything for it. It's a welding shop.

Nice test ! Thanks, bro !

Good video❤❤❤

Good!👍👍👍

Deusolivrequarde passei 38 anos de minha vida fazendo isso , não guento nem ve mais isso .

Amator

It's a conversion insert that gives you the option of using a positive rake cutting edge with a negative rake toolholder.

MASHA.ALLAH.GOOD

Yes, looks like positive rake insert three tries and discard. China ones work also. E-bay clones work well too.

Inserto stupendo! Ti ringrazio del prezioso video, un saluto da Roma. 👍👋