Wild West Garage

Пікірлер

@4AM_DJ 4 күн бұрын

I changed my fuel filter and went to start the truck following priming procedures for an 04 truck. Long story short, after replacing the lift pump, replacing a starter that i burnt up, testing the battery voltages, and draining-refilling filter housing with diesel, all thats left is this cp3 pump.

@WildWestGarage 4 күн бұрын

@@4AM_DJ sorry to hear that. I looked after a fleet of these trucks, never had any problems restarting after a filter change. I would change the filter, cycle the key a few times and they would fire right up. I’ve never had to do it but there must be a way to check the pressure.

@leonardryan8723 5 күн бұрын

Morgan you got to are weight often to the pulley. You need weight for crusher to work . Try start of with old car front break drum .

@WildWestGarage 5 күн бұрын

@@leonardryan8723 it crushes no problem, the material just doesn’t want to fall through

@paulgreco2188 7 күн бұрын

You have the patience for metal work my friend. The metal sure does strange things went dented...

@WildWestGarage 7 күн бұрын

@@paulgreco2188 can be challenging for sure

@jimholz1102 12 күн бұрын

This one sounds like it comes "on the pipe".

@WildWestGarage 12 күн бұрын

@@jimholz1102 my favourite pipe, unfortunately it’s the most time consuming of all the pipes I’ve built.

@naturundhund 13 күн бұрын

😎👍cool.

@naturundhund 13 күн бұрын

Great Job Morgan.... Greetings from Germany Peter 😎

@steveyoung9104 17 күн бұрын

Deadly "A"😅

@steveyoung9104 17 күн бұрын

Mogadore Body Man Estroidniar😊

@martyrutter3630 17 күн бұрын

That torch trick was so cool to see in real time. 👍👍👍

@WildWestGarage 17 күн бұрын

@@martyrutter3630 that even surprised me a little bit, every day is a school day.

@martyrutter3630 17 күн бұрын

Just relaxing to watch your skills and patience you work with to achieve an amazing outcome. Fantastic job my friend. 👍👍♥️

@WildWestGarage 17 күн бұрын

@@martyrutter3630 Thanks Marty

@kevinhall2266 19 күн бұрын

Majical Morgan. Saving better times.

@naturundhund 19 күн бұрын

Hey Morgan... You did a really good job. I'm a car painter and would be happy to help you... unfortunately you live too far away from me. I'm excited to see what it looks like when finished. Greetings Peter from Germany.

@WildWestGarage 19 күн бұрын

@@naturundhund thank you

@cameronhamer9432 19 күн бұрын

The more you beat on it the more wrinkly it gets , the way I was taught on shrink metal was to heat a area , slap hammer the metal inward and quickly cool it with a wet sponge . Roofs and hoods are the hardest , looks good to me , a work truck gets beat up after some time anyway no matter how you try not to . 👍🇨🇦

@jasonthomas4738 20 күн бұрын

Good work Morgan

@timwatson4524 20 күн бұрын

Looking good

@lonniechartrand 20 күн бұрын

I remember doing this exact same process, working with my dad, 52 years ago, on a ‘40 Ford pickup.

@brianfrancis2862 20 күн бұрын

will it work on vw railbuggy

@WildWestGarage 20 күн бұрын

@@brianfrancis2862 Yes

@richardfrost7575 20 күн бұрын

It is such a privilege to be able to watch a true craftsman at work. One of my nephews is a true body man as you are, most think a body man's work is easy, a little bondo and paint and your done. The kid ( he's 48 don't know how he got that old I'm not) is able, like you to make parts from sheet metal etc. I know there's more to it than that just a true craft and art. So much more can be said just not enough pages to say it. You either know or you don't. To many actual crafts being lost in this world, thank you for giving us an insight to your world and craft, maybe help inspire others like my nephew ( he caught the bug young) to take up this kind of work, unlike when I was a kid there are very few if any to learn from. ❤ didn't mean to ramble and praise to much just saying something I think needed to be said. You and Buckin are an inspiration to us all.😊

@WildWestGarage 20 күн бұрын

@@richardfrost7575 Thank you. I’m grateful that I’m able to do this kind of work and for the inspiration I’ve received watching others displaying their talents here.

@acjack1169 20 күн бұрын

Wild Wild West...Here from the land of the Sleeping Giant.. ..Nice Video thanks for the update, Have a great week keep on bending..

@saltrock9642 20 күн бұрын

The excitement is building in these videos plus we get to see your automotive mastery.

@CarCommentator 20 күн бұрын

This video is a masterpiece! The way you bring old, forgotten items back to life is nothing short of magical. Thank you for sharing your amazing talent with us!

@waynetharp 20 күн бұрын

Thanks for sharing... I have seen a lot of guys around my area use the spray on bed liner all the way around the bottom foot or so of their work trucks to protect metal/paint from tire flipped rock chips. I believe they add the paint in to the spray on liner. Do you think this would actually slow rust or are they trapping moisture between the spray on and metal?? My truck beds dont seem to rust from the spray on bedlining. Anyhow...If the roof metal is notorious about pin hole rust and leaks on these old Fords. Maybe the spray on lining would stick better then filler on a cab roof? It would definitely hide inperfections and might help from low branches scratching the cab top in the bush also?!?! Just thinking outloud again...👍

@WildWestGarage 20 күн бұрын

@@waynetharp I’m not a fan of that stuff, especially in a situation like this were it would be going over old seems that have rust that I can’t get at to clean. I’ve seen where the rust has run under Bedliner and created a big mess. The roofs on these trucks rust from the inside out. I’ll be cavity spraying everything after it’s painted. I’m not worried about imperfections on this project, it’s going to be a masterpiece of imperfection. This cab is 48 years old and I’m pretty sure it will last at least another 48 after I’m done with it.

@waynetharp 20 күн бұрын

@WildWestGarage Thanks for the info and experiences.I had always wondered and questioned the long term when seeing guys using it...Maybe if Ford hadn't been so stingy with the paint at the factory, these cabs would have lasted even longer.

@vintagesawyer6246 21 күн бұрын

The cab is looking good! Maybe hit it with a bit of short strand fiberglass filler to smoth it out a bit (?) It's stronger and sticks better than plastic filler. I like your Oxy-Propane setup 👌

@WildWestGarage 20 күн бұрын

@@vintagesawyer6246 If this truck was going to be a pavement Princess I would fill the roof but it’s not so I won’t be using any filler on the roof. You’ll understand when you see the finished truck.

@vintagesawyer6246 20 күн бұрын

@WildWestGarage I get it. I watch welderup, too .

@aaronpowell4885 21 күн бұрын

Beautiful work Morgan! Bodywork is one area of automotive I stay away from. With exception to when I was dirt oval racing, where a sledge and prybars were perfectly acceptable😅

@reliant_turbo 21 күн бұрын

its drastically improved.

@davidpetrus1748 21 күн бұрын

nice job i totally commend you on your patience now you are this far i recommend a little rage ulta to fine tune it if you don't have it locally then order it online you can thank me later and yes it is pricey but worth it trust me no more buying polyester putty for pin holes you just use the bondo it sands that nice

@WildWestGarage 21 күн бұрын

@@davidpetrus1748 thanks David, to be honest I probably won’t be putting any filler on the roof, you’ll understand when you see the finished truck.

@davidpetrus1748 20 күн бұрын

@@WildWestGarage ha ha I'm sorry i didn't listen to your last words at the end of the video you are right that is above everyone's head so why bother again I'm sorry my bad still an Assum job you did on it

@BuckinBillyRaySmith 21 күн бұрын

I am getting very excited. Thank you Morgando I loved the fallin’ wedge

@martyrutter3630 17 күн бұрын

It is looking good, Morgan is doing his magic. Such patience and skills this man has.👍👍

@richardpichette4380 21 күн бұрын

I hope you’re expensive, Morgan, because if you’re not, you should be.

@WildWestGarage 21 күн бұрын

@@richardpichette4380 I charge

@Dunlap-uj5zl 21 күн бұрын

👍👍

@justinweaver8107 21 күн бұрын

Comin along VERY WELL❤

@oscarmdog5275 21 күн бұрын

Thanks for showing the process! Most don't know or understand the skill and learned movements to even attempt this kind of work! 90 minutes on one area! 👍👍👍

@WildWestGarage 21 күн бұрын

@@oscarmdog5275 you nailed it, I spent about 3 hours between the two dents