Easier to remove the tail cap and check the batteries every few months.

Works brilliantly! Your parenting skills with patience and humor shows a great dad.

Martin Flats

Hard to concentrate on what your saying, the music is very irritating

Thank you Greg! I'm in the process of putting a hood scoop to accommodate my big block in my 75 stingray! Nice to know I'm doing it just the way you explained! Jim merino Frank son! You and Scott worked on my 75 and Pappas 65

Thank you

I’ve got the weiand x-celarator 625 Barry grant Demon dp 14x3” drop base and only have about 5 or6 mm clearance in my XE. Are you getting the clearance with the spacer because the moroso drop base is lower than most Love the vids great work boys 🤘

Better check that shock shaft got weld splatter, didn’t bother covering anything up when you busted that welder out….smh

most of these how to lessons use air or fans to blow dust, I don't know why they don't use vacuum ?.

I am planning to buy a bike in LAS VEGAS . They usually look almost news BUT are they in good condition to run OR do they tell the buyer if it's in good [or bad] condition to run ???

Beautiful!!!! Explains each step, tools required, process, visuals and no crappy noise pollution!!! THANK YOU!!! ❤❤

IIt's not acid but alkaline. When alkaline batteries have leaked it's hard to remove all the gunk from a device. Acids can be used to neutralize the alkaline. Vinegar works but I'm using vinegar essence diluted to a concentration of about 5%. When the acid reacts with the alkaline, the alkaline will fizz for a short moment. Continue until the fizzing stops. The rinse and dry thoroughly. This does not remove all the chunky bits of alkaline battery goo but it neutralizes it removing its corrossiveness. I've used this numerous times to deal with leaked batteries in all sorts of devices. It failed me only once when a circuit booard ha already virtually ceased to exist before I started. Lesson learnt: remove batteries from devices when you don't use them. And don't ever trust batteries advertised as leak proof. In my experience ALL will leak sooner or later. Be extra paranoid with batteries stored under extreme conditions such as in hot cars.

Two great tips...wax paper and trimming the brush.

Great content but very distracting music during your presentation. Leave the music off during your talk and it will be more effective.

Mine is not LED, but a bulb light. Any recommendations?

Love it! “Quit smoking” - blows bondo in the air with no mask 😆 Good vid tho.

Worked PERFECTLY with a maglite I got for free because corroded batteries were stuck - Used your method and had it working perfectly in 10 minutes. Thank you so much!

Great tips. Thank you

May 2024 repaired a led maglite following this procedure. It works.

Just finding this because I have this issue. However the top of my flashlight does not screw off… I’ve tried. It’s not the same brand as yours… it’s frustrating me but unless I can screw the top off I think my little tiny flashlight is for the scrap heap.

2 years in the bottom of a trade show bag. Thanks for sharing, worked flawlessly

Your son is adorable so precious im giving you a thumbs up and subscribing for him be nice to your babies no ones future is certain

Next time PAUSE the Video and PAY ATTENTION to your son!

Your information was PRICELESS!!! But I enjoyed your patient interaction with your boy even more!! The world needs more Dads like you! Keep up the GOOD work!!

great vid, but can that music please

brilliant! thanks. got two to fix!

What was the RPM.

You guys make a great team!

Cool❤❤❤❤❤

So you changed the stock 351M open chamber heads that nobody uses for a very expensive aftermarket set of Edelbrock heads with roller rockers and only gained 25 HP. Seems like a monstrous waste of time of money to me. Maybe just a set of actual closed chamber Cleveland heads and wala the same result. Kinda goofy test it seems to me.

Can't believe this video popped up in my feed! I lost one of those identical flashlights many years ago, and just found it last week. Went to change the batteries, and they were FROZEN. Couldn't get the second battery out, and didn't know how to get the LED out, so I threw it in the garbage. Just pulled it out of the garbage and used the socket trick. Couldn't hammer it out, so I had to go to an arbor press and press it out. I had to get all the crap inside of the light body out with a file because it was so bad. Put it back together and it works! THANK YOU!!! 👍

Nice instructional video and you did a great job. This is a video on how to repair fiberglass, correct? Not an annoying frigging music video, right? That noise is highly distracting and hard to watch you and listen to that crap. You don't need props when you do nice work as you do.

When does part 2 drop?

Great vid.. but.. why having music?

Excellent!

LMAO !!! saving lives 🤣. So my Solitaire Mag won't open where I put my batteries in. I am wondering if the corrosion sealed up the opening and it is a mother to unscrew, I've tried pliers and tapping it. It is really stuck.

Would love to watch an informative video without super loud engine noises and music playing while the person is speaking. I’m not here to be entertained, I’m here to learn about a process

You saved my life. Let your kid know. Extra points for handling the wild beast like a pro.

Very nice explanation, good job, thank you!

Thanks for the help, I was able to fix one I gave my Dad a few years ago. He forgot to check the batteries and they leaked, luckily it wasn't too bad.

I have the exact same lite and the original Duracell batteries are stuck in it. Because it was the bottom battery this did not work. Even using a 5lb hammer it did not work at all. I was hitting so hard that the bottom of the lite was getting distorted, those batteries are fused to the walls.

nice back ground and a good teacher.

Is there a part 2

Thank you I finally understood what I had to do after your helper showed up 😊. Seriously though I liked the instructions.

Yeah, the Stock heads were 2V turd heads. Gee Wizz, I wonder why they didn't Compare the super flowing actual Hi perf 4v heads?

Thanks!! Worked for me👍🏼

Question for anyone that might know. Would a bit of dielectric grease help prevent the corroded battery/batteries from sticking to the walls?

mesmo com esta ferramenta, numa s1000rr fica difícil pois a não é simétrico o topo de uma bainha da outra.

Sucked considering the change to aluminum heads, roller rockers and different cam. Torque was down (!) with only 24 HP increase??? Not worth it or parts weren’t properly matched

What if the bottom part won’t come off?