Size of the tubing?

Got an A

What was the thickness the tubing that you use. I'm planning on building something similar. I'm guessing you used ¼ or ³/¹⁶

I would like to know… what is the exle witdh if the trailer size is 6x10ft

Man the way this guy describe to hook up your subwoofer to make it from 4 ohm 2 ohm he said take a positive wire to the negative the negative to the positive and then run your positive wire from the speaker and then take your positive and negative to your aunt destroyed my system he did not explain it correctly and now I destroyed my sister hooking up a one speaker from a 4 ohm to a 2-ohm am I doing it his way it made me blow my speaker and caught it on fire and my aunt so now I'm out of a P3 Rockford fosgate 15 inch subwoofer in a 1200 watt Rockford fosgate amp preciate it fella

I'm in the Dallas area. Do you still have any of the fiberglass you are willing to spare?

Awful audio.

pretty sure you're massively underpowered still at 2ohms 🧐 good how to though

In Canada we use a square head, we call it a Robertson. Very common here for most construction jobs.

22 outlets, not 32.

Thanks! I got the first two screws, but I didn't which of the other screws i needed to remove so that i could take off that filter bracket. Super helpful! I didn't realize how dirty it was going to be under there 😬

652.6 pounds

Hello there, we would love to send you our product to review. What is the best email or contact with you? Thank you so much

So did I miss how much the table top cost? Not all the metal stuff just the top.

Hey JimEd...great job! Remember to put your link in your comments and then pin it ;) Feel free to delete this comment.

I think yes I would definitely remove the door it would just make it easier I think but I have another question do you not need a rubber gasket or something at least on the back side to so it's airtight where it keep cold air out I'm simply asking because I'm planning on putting one in and I don't want to lose my heat and air thanks

How are you guys sure that the trailer is square and not warped towards a corner?

670lbs

Mine did this it was the motor I had to replace it

You never ever leave the handle in the high lift jack like that! Wow ! Everything you did was the wrong thing to do! Iron worker 30 years!

I was thinking about your comment using chains and a bolt to lift up fence posts. I was thinking you were going to drill a hole near the bottom of the 2x2 and finish lifting the table with the chains on the jack.

Thx

This is the scariest video I have ever watched on youtube. I had to fast forward to make sure it ended OK. I love that you called those welds 'safety welds'. Not the term I would have used. I am a staunch advocate for free speech, but if I were to support banning videos, I might start here. I hope no one else tries this in the way you did. I think there are pretty easy ways to do this in a safer manor. Good luck to you. Please stay safe in the future.

Same problem with mine all it needed a capacitor from Amazon

Bad capacitor

I think he needs to first learn how to lay down a good weld first. Bird crap!!!!

Omg bro, I was so worried about it coming loose and landing on your head!

I noticed that you started with using the roller and ended up switching to the chip brush halfway through. Was it a bad quality roller that smeared the mat around because it wasnt rolling freely or did you ever figure out what the issue was? I built one of these enclosures back in 2019 and I also ended up fighting with the roller because it was sliding the mat around instead of flattening everything out

👍👍

I've done some **sketchy** things, and even I wouldn't do what you did. Glad you weren't seriously injured. Cool table, though.

OSHA would be proud of you.

Nice content! How to register trailer? length of neck?

Not sure why people expect paint to stay on if they are not using the primer. Prep is always key. Also I know some people just spray the paint on and never bake it as per the instructions. Sometimes that is the problem as well. Please though, use the primer if you like paint to stay lol.

653 lbs.

Did you get an F for safety

Anyone crossing this down the road. If it’s not the bearings. Wasn’t making a bunch of noise. If you remove your pumps back cover. Shut the breakers off. A can with your fingers or with a pliers very easily turn the shaft. If you turn it on. While it’s buzzing. Very careful with a loose grip with some pliers. It you give the shaft. Even a quick 1/4 of a turn a pull the pliers off at the same time you do the little turn. The pump will take off an start running. Just as normal. A run all day. But if you turn it off. You’ll have to start it the same way again most likely. It’s due to the capacitor is bad an don’t have enough kick to get it spinning on its own from that dead stop. Most of the time. If it’s the bearings. You would have noticed your pump making a little noice or rough running sound. Or up to a really bad sound. An it finally locked up. An if you pull the cover off. If you can’t easily spin the shaft. It’s locked up. A you’ll hear the bearing making noise when you turn it if you’re able to. You can easily tell if it’s one or the other. Or if ya got a multimeter. Can kill the power pull ya capacitor off in hook it. Have an insulated screwdriver an touch both sets of prongs a couple seconds to discharge it. Read the sticker an just test it with the meter

What was the cubic feet? Im guessing .5

the bed can up 90 degre?

Excelente y disculpa. Esa sierra te trabaja bien con el disco evolution para metal? La quiero, pero tengo esa duda!

It's 4 years later, is this guy still alive or has he collected his inevitable Darwin Award? This was like watching one of those "Faces of Death" videos. You know it's coming. Dude...make friends or spend bucks on equipment. Pro tip, you need heavy stuff moved, set your lift gear up, wait the neighborhood lawn crew is working, slip them some bucks to assist. That way at least the wife doesn't come home and find you splattered over your shop. Also, making that table top solid was "less than optimal". Should have made it using 4-6" wide x 4' slats, (order the slats cut to length) leave gaps between the slats, now you can clamp stuff and it's one heckovalot lighter. Want a solid surface, order 1" slats to lay between the wide slats that you can take in and out as needed. Frame it out, get your castors on, get it leveled, then weld the top slats on. No muss, no fuss, no death defying acts required. Making it with that big of an overhang and no support, means your edges will droop, and you can't make bolt-on dogs on the sides to easily line your work up square, weld on tool holders, or easily access storage underneath it.

nice

I cleaned it just as you suggested and it looks great but the dry still stops before the cycle is over and says clean filter. Is there any way to reset it to the original settings?

take the carpet panel out of the trunk, it will keep the same shape

I’d say that the table top weighs 650 pounds.

Hello, do I need to use a primer before coating? I saw that you used VHT flameproof primer before coating. Do I actually need it, or can I directly apply the coating?

A crane on the ceiling would be handy!

Funny you ask about removing the door. I assembled one previously and did not remove the door. I was debating with myself during the video whether to or not.

Hello sir thank you for make this video for help I have one question if you can help me can install 2 subwoofer with dual voice coil 4ohms and wiring amp play 2ohms thank you

Pointless

What if you have a Storm or screen door on the outside how do you install it then with out have to permanently remove the screen door