EJwasHere

Пікірлер

@endaugadget6679 Күн бұрын

👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

@awdboost314 2 күн бұрын

Does the bumper need trimming ?

@tigerboss786 3 күн бұрын

Beautiful mam

@jefflamb5343 4 күн бұрын

Regarding the erratic arc start, as you (and others in the comments) have pointed out, make sure to use at least 1 sec of pre-flow and preferably even a little longer (I tend to run 1.3 sec). Plus, make sure your ground is very good (ground directly to the piece you’re welding or use your heat sink and make sure your piece has very good contact to the heat sink which is flat and has very good contact to the grounded table). And the third thing is this - when using the foot pedal, immediately go to at least 50% pedal before the arc starts so when the arc does start it’s a quick and direct burst of higher amps that tends to snap directly to your target rather than wandering around when you start too low and try to slowly feather the pedal during the arc start.

@azizalouache9583 5 күн бұрын

welcom

@Gil_79MPh 11 күн бұрын

That blobeye is🔥! If you dont mind what is your height? Im looking for the same for the wife.

@kae2geeked 15 күн бұрын

3 years late but for the code were u having o2 sensor problems aswell with this? i keep getting misfire codes on coldstart then i replaced o2 and now its popping up with po13f which is lean to rich o2 sensor delay

@OleRazzleDazzleSRC 17 күн бұрын

How's the pano v2 holding up? My only concern is the usb charging instead of battery power.

@kko8603 18 күн бұрын

You’re cute

@crazycaseyscustoms 21 күн бұрын

Rad!

@crazycaseyscustoms 23 күн бұрын

Hey EJ! I worked for Scotty around the same phase of my own career. I was one of his first employees at Chuckles Garage. He was a bit harder to work for back then, but I will say that he is one of the most genuine people you will ever meet, and if you work hard for him, he will have your back forever. I had seen you popping up on his social media a bit, but had no idea who you were. Enjoy California! It’s a special place. Man, I miss eating fish tacos staring at that ocean.

@kevinheiman5615 24 күн бұрын

What kind of gloves are those?

@LandMineFX 27 күн бұрын

My wimpy office hands cringed seeing her do that barehanded 😬

@kevinheiman5615 Ай бұрын

Phenomenal

@lanceboyett9034 Ай бұрын

Wow, color blue is that, I want to paint my snowmobile & fourwheeler in that bad @$$ color. Nice video.

@AludranReptiloid-p5q Ай бұрын

GoooooooooDDDDDDDDDDDDD~

@Alexander-Ra777 Ай бұрын

In Russian, your initials read hedgehog.😅

@JeffRobbins-p2d Ай бұрын

Absolutely awesome you being you and accomplishing anything and making awesome stuff and being a girl getting dirty and having a idgaf attitude you F***ing Go 🤟

@JeffRobbins-p2d Ай бұрын

Absolutely awesome seeing you doing an accomplishing anything you want and being a girl who dngaf attitude you F***ing go🤟

@Mattlawton-ft6ew Ай бұрын

🤣👍

@thatdudeinorange5269 Ай бұрын

Bastards! 😅

@jamesbrussels5776 Ай бұрын

Longer video would be great

@sierrabound Ай бұрын

LOL...at around the 13:15 mark you didn't want to take your gloves off to handle the metal as it might have been too hot but then you touched it to your face to confirm.

@ocdetails Ай бұрын

You won't spill gas if you pull the fuel pump relay (green plug under the passenger footwell) and then try starting the engine a few times to use up the gas in the system. Also, don't forget to lubricate those rubber ends. You can just rub a little motor oil on them as lube, but for injectors it is worth it to make sure you don't have an issue. Great video! I have a 2002 that is a bit of a project car at this point and I needed to put in bigger injectors due to the bigger turbo I put in and this was a big help. I haven't done injectors on an EJ before, so this was really helpful

@sunyoic.a6844 2 ай бұрын

hola saludos como isiste para comprar la maquina y cuanto te costo saludos gracias

@JusticeAngel 2 ай бұрын

Sit on my face

@troys3537 2 ай бұрын

Hello nice welds, was that on 220 or 110?

@Hood_Tyme_Fab 2 ай бұрын

Your flying

@Chewpapifuqs 2 ай бұрын

This aluminum or stainless steel

@fitch8363 2 ай бұрын

I have a PW225 like yours. A little arithmetic suggests the three division marks between 40Hz and 200Hz are 80Hz, 120Hz, 160Hz. Similar arithmetic suggests the divisions on the balance are 30%, 50% and 70%.

@thatdudeinorange5269 2 ай бұрын

Wow! Proof that practice pays off 🙂

@tommcilroy8440 2 ай бұрын

Plenty stacks of dimes there lad, class song too 🤙🏻

@lailafroehlingsdorf4316 2 ай бұрын

Those are some clean ass welds

@thetintwizardsllc3128 2 ай бұрын

Clean ass welds

@chrisriveras6107 2 ай бұрын

Have you tried ocxilne Oxygen welding

@chrisriveras6107 2 ай бұрын

Perfect welds ❤😂😂

@TheDamian9011 2 ай бұрын

👍🏻

@alexalexanderivanov5815 2 ай бұрын

tight

@MatanicFabrications 2 ай бұрын

Gorgeous, and i aint talking about just the welds

@brensbands9335 2 ай бұрын

Funny how a man posts something like this even with amazing welds he will immediately get hate comments. Notice how all comments are peaceful on the woman’s post…..