Another shop SAID they replaced them and charged the customer for the service

That’s cool I will have to try that my next oil change

Notice that OEM does not use metal End Caps. Metal End Caps are not an indication of Quality in conventional Oil Filter design.

the filter gave you hell to the end? Be shure to remove the old seal.

I have to be real. I just did an oil change with this type of filter. You can just unscrew it a bit and it does the same thing just might have unscrew it more when it slows down. The only other difference is you can unscrew it white it drains simultaneously. Useful for a shop setting where you’d see multiple cars a day but for a single person doing their own oil change, this is quite a waste of time. A couple of those blue shop towels and your hands are clean again 🧼

No gap

i suck the oil out of the top with a turkey baster.

Drill baby drill 🛢️

I pee on it

I followed your instructions, thank you for the video. The message went away after I disconnected both batteries and waited 20 mins. I replaced the battery with OEM as well. The stop/start does not work though, do I need to do anything to reactivate it ?

I just grabbed an old nail eight penny or 16

Just use disposable cars, dont gotta do none of this shit

Thank you so much for making this video. I need some advice. I have watched the video a few times before trying to replace my support battery. I haven't change it for 7 years and didn't even know it exist. I followed your instructions until got stuck removing the bolts. I have removed the right side, but the left side for whatever reason won't come out. I used a 6-point 8mm ratchet wrench. I sprayed multiple times of WD40 and PB blasts with 2-3 hours waiting between each spray and wire brush trying to removed any rust, but still can't unscrew. I noticed the battery cover moving up and down while I was unscrewing. Could you please tell me what that means and what else can I try to remove the bolt? I have tried more than 24 hours so far. Please help. Thank you.

Overheated… the yelloish belt around the base gives that away…

Mines opposite. If I drive 5-30 mph it shakes, if I push the car, it drives smoothly

Looks like the gap is to big

It's gap is too big

No crush washer

Make sure it comes loose first

Gasket missing. Its not creating a complete seal to create proper compression

The spark plug was loose

Missing seal

It's in your hand and not inside the engine

You tell me Sherlock. Ur the tech

Bro fr thanks

It is missing the seal/gasket at the base of the threads. That’s why the porcelain is so covered in soot.

It's gay

Wrong gap.

Compression leak

When was the last time you replaced your spark plugs?

Bro you have plastic gloves on your hands won’t get dirty

Gap

It's a cheap red car quest oil filter. Do it to a quality oil filter. It holds oil. It'll spill out the top when removing.

😂😂

Thank you!!! Followed all your steps - worked perfectly.

Thanks!

new car 7500 miles, i don't wait that long, i go normal synthenic 5k miles change. some do 3k

Damn. Course mine uses paper filters

Close a screw clamp on the end of the O2 removal. Then, tightened, a lil, then, loosen. Add, antisieze. All new vehicles..remove stuff and antisieze

Good job, partner, good job… I’ve been saying it forever…

I have a friend, he just run the engine dry without a single oil change, buying a new car after the engine stops running 😂

Can I just do the whole oil change right there?

Inspection plates are awesome 😂

Heaven forbid you get dirty oil on that nice clean rubber glove. SMH.

Hi, is this the same engine as in the Volvo V40 T5, 2018, 245HP? Thanks

Imagine beo forgets he already changed the filter and stabs the new one

What if the oil filter fits in sideways then what tech tip lol