Thank you so much, dryer now working. You explain slowly and clearly so that I don't get frustrated. Thanks!

My back hurts watching this, get a chair man.

I will be attempting to change mine on a 05 GT manual transmission. I had an 8 year old battery, assumed it was the battery, bought new battery , same strange noise from starter, not grinding sound, a weird sound like air ratchet gun. I assumed my older battery was not putting out enough CCA’s. But, apparently that was not the case. Will report back later!

Do you remember how much pressure you used with the wheel?

Great video my car isn’t responding or turning on and battery is fine so it must be the starter so I’ll try to work on it thnka

can you use contact cement or 3M 77 Spray Adhesive?

Hello, can you tell me what the tq # . For the front nut brace tower. I have a 2007 shelby GT500 convertible. And I can't find the right info. Thanks

Thanks so much

I appreciate this tutorial doesn't require taking the drum out.

Nice try lol

I have the same paint scheme as you. Mine is a 2008. Thank you for the video.

Thank you so much for this video. You, and so many other generous people have helped me so much with repair and maintenance work on my vehicle. You make the world a better place. I am really, truly grateful.

The 6 wires get mixed up pretty easily. Why not provide a diagram to make sure we can see what goes where?

The unit turns on but it says to do a filter check and I don't know where that is

Today I followed this video instruction and my Honda Odyssey 2003 problem was resolved immediately.

I flip cars and i usualy just sell them with the actuator clicking if it does. Today i decided to figure it out. I have 2 actuators bad. I dont want to pay 80.00 for them and i dont want to wait for the 22.00 set from eBay. Which is a great deal. Watching your video gives me the confidence to open them andfix them myself. I dont have motors so i may just rebuild thr motor as well.

As another mentioned, use spray adhesive instead of a hot glue gun. A soldering iron with a pointed tip might could be used instead of a knife

Damn. I bet that's the problem. Thank you so much! 😄

Thank you!

I have a 2006 Odyssey does this video relate to a 2006?

Brilliant video and my alternator just went and the mechanic wanted 600/1000 dollars just to replace it. However by watching your video I can do it myself.

7:24 Those grooves were made by the manufacturer for the purpose of balancing the shaft. Do not spread falsehoods if you do not know the subject in depth.

My power cable just broke off my starter so now I need to somehow crimp a new copper circle on

Great video

I was wondering what that light meant ! Panicking for no reason 😂😂😂😂

so easy!

Thank you

😊 awesome 😎 teachong thank you soo much ❤

Jeff thank you so much. Saved me hundreds and only took 2 hours and a couple of mere flesh wounds.

Thanks Jeff!

*Manual transmission* Unfortunately the switch on the brake pedal wasn't causing my issue. However while checking the brake pedal, I noticed a similar switch on the clutch pedal. A penny and some duct tape and I was back in business. This also cleared the VSA light that came on at the same time the cruise stopped working. Thanks for pointing me in the right direction.

Jeff, my cruise control on my 04 CRV comes on but it only will stay on for about two or 3 miles

Those same black thick sheets I’ve used for years as foam inserts for my work boots as long as your boots are just a little over sized you can remover you original insert trace it cut it and put under your original one it really helps and is way cheaper than any store bought insert that seems to stop working after 2 weeks 👍

Hey thanks jeff this was the most informative video ive seen thanks i like doing my own work and this deffinatly helps keep up the good work

You are a god. Ty sir

OUTSTANDING CONTENT CREATION!

How do you which way the thermostat and fuse go on no one is specifying that. Would be nice to know.

Great job Jeff ‼️

Thanks for the video buddy I was stressing about replacing my 03 3500 starter. Only difference from your video was mine had 3 bolts holding the starter in. Very informative and just what I needed. Thanks buddy!

I used a yoga mat

Im gonna use this info to try to make this repair on my 2004 honda odyssey, looks like the most efficient video i have ever seen in doing a repair at home. Im gonna check to see if my brother coukd help , i may not have the arm strength to do it on my own. 😂

It's not a strut.

I fuck with you, Jeff you’re the man

About to replace my unit but the color of my wires are opposite on leach element. Is this an issue?

Maybe it's too late and you don't have the car anymore, but I'd sure love to see the trick to replace the window ( driver or passenger ) regulator mechanism. This has broken on my car 5 or 6 times now and for $200+ to fix it is a major aggrvation. I bought the part and tried it twice but had to take it to the shop because I could not get the thing installed.

8:32 - When you say "I lowered the hood, but it really isn't necessary to lower the vehicle" ... do you not mean just the opposite? That is, lower the vehicle with the hood up or down? I guess you are saying in a way that seems odd to me that it is not necessary to lower the hood to lower the vehicle. Also, when you are adding the transmission fluid to the engine, it looks like your flexible hose covers the entire access hole for the transmission fluid dip-stick ... so how does the fluid get in to push the air out? Did you get a lot of bubbles in the hose or is there a hole in there somewhere for the displaced air to escape?

Thank you Jeff

Thank you!!!

Same steps for 2010-2014 mustangs. Part # is slightly different but the process is very similar/almost identical.

Thanks Jeff.