Пікірлер
@lisavaniderstine6212 Ай бұрын
What size needle should I use?
@shannonyoung9233 Ай бұрын
This is fantastic HOW to video. Thanks so much for making it. I had to go right over and buy both files for all sizes. MAY I ASK which tab did you use. Im following along but my tab I used was not as wide as yours!
@alicebrown60 2 ай бұрын
What Madeira thread do you use for embroidering fonts on marine vinyl? I am using 100% polyester 40 wt. I had somewhat less breaks using your embroidery setup suggestions (cutaway stabilizer, 505 basting spray, SF101 interfacing, 75/11 ballpoint needle), cutting the number of shredding and thread breaks down from every single letter to about every other letter. But my font is too thin and gets sucked into the marine vinyl even when I use a topper. I am making key fobs with embroidering 1/4” font “In loving memory of…” I even had the wording all professionally digitized. Any suggestions? Any suggestions on a site to purchase a bold 1/4” font to embroider on marine vinyl? Thanks for any advice you may have.
@littledevildee 2 ай бұрын
What is you opinion on using edge paint stationary rollers--the kind that have an ink well and a roller that sits on it like a tape dispenser version? Sorry for the wonky eplanation lol. Wonderful video, thank you!
@NIAZULHAQ-k5n 3 ай бұрын
Which one is the best machine for threadmode embroidery?
@charlenefiumara333 4 ай бұрын
Hi, I just love your designs and videos. I just made this one and it came out great. What size snaps are you using?
@janepronovost3267 4 ай бұрын
what were you rubbing along the sides after cutting it out.
@lavonnewalker373 5 ай бұрын
My largest hoop is 5 X 12. Can this pattern be split so I can us this smaller hoop. I have an Brother PE 900 largest size is 5X7 if not a split pattern with 5X12. My spouse and his friends are golfers :) Thank you!
@suzannewurster505 5 ай бұрын
Thank you so very much for the Tutorial!!! You have done such a great job of explaining the process, and at a pace one can comprehend each step you explain. Thank you!!!
@ufoquilter86 5 ай бұрын
Why do you use the cardboard and how thick is it?
@ufoquilter86 5 ай бұрын
What is the best type of vinyl for these?
@mrsmrs4844 6 ай бұрын
I am considering getting either this design or an unquilted design. Are you using cotton or polyester thread to make these designs? I am concerned of the possibility that the polyester thread will melt once the thread comes in contact with the hot pan/dish, etc. Do you have an unquilted version? If you are using cotton thread, can you please advise where you got the thread? Thank you very much.
@threadmodeembroidery2374 6 ай бұрын
Hello, I use a polyester thread not cotton. I have not had an issue with melting however I don’t carry hot things very far, just from oven to hot plate holder.
@deetata8936 6 ай бұрын
This is really lovely! I'm going to incorporate it into some of my designs 💃💃💃
@threadmodeembroidery2374 6 ай бұрын
This design is specifically digitized for foam.
@deetata8936 6 ай бұрын
Very nice! But how do you stop the paint from staining the thread. I make embroidered key fobs also and most times I use same color of thread as the faux leather or I use black thread.
@threadmodeembroidery2374 6 ай бұрын
I don’t get paint on the thread, if I do it’s an accident. The paint would definitely stain or colour the thread. It’s important to be slow and careful to just get it on the edge.
@amazingracie212 7 ай бұрын
What kind of vinyl are you using, it doesnt look like marine vinyl, it almost looks like cricut vinyl.
@threadmodeembroidery2374 6 ай бұрын
I use a marine vinyl or an upholstery vinyl. It is definitely not Cricut vinyl as that would never hold up. I get my materials at a local fabric store and they frequently carry an array of random thicknesses of vinyl.
@berpyschannel5584 7 ай бұрын
Thank you so much for sharing this video with us! a question, I am using a different brand and I have a terrible problem, it continues cracking on the more flexibles parts it doesn't matter how I do apply the paint, at the beginning looks beautiful and after a few days the paint cracks, does this happend to you with this paint in this kind of pieces?, I can see you create very flexible and high traffic pieces and still looks amazingly ! thanks on advance!
@threadmodeembroidery2374 6 ай бұрын
Hi, that is very sad, that after all the work painting it, it cracks. I am not familiar with other brands. This is the one that I’ve used from the beginning because it worked so well on leathers that are also very pliable. I think the only way to find out what works for each individual, is trial and error, unfortunately .
@MyaFan443 7 ай бұрын
I was hoping for a digitization video 😢 These are cute.
@ufoquilter86 7 ай бұрын
How fun
@ufoquilter86 7 ай бұрын
What type of scissors are you using? Those look like they cut through butter!
@threadmodeembroidery2374 6 ай бұрын
I like Kai and gingher scissors. 👍🏼
@ufoquilter86 7 ай бұрын
When I purchase the design, do all of the hanging/loop options come with or do I have to purchase each individual type?
@threadmodeembroidery2374 6 ай бұрын
Each listing has a picture of the files that are included. It’s best to check them to make sure it has what you want.
@ufoquilter86 7 ай бұрын
Do you have a link for your rivet press, please?
@threadmodeembroidery2374 6 ай бұрын
The rivet press I use is from Buckleguy dot com. I think it may have changed a bit from when I bought it.
@ufoquilter86 7 ай бұрын
I have been waiting to make this one! Does this file come with an SVG as well?
@threadmodeembroidery2374 6 ай бұрын
Hi, no. None of the files come with SVG as I don’t have a cutting machine to use for designs.
@ufoquilter86 7 ай бұрын
Do you have a link for the exact size rivets you use please?
@threadmodeembroidery2374 6 ай бұрын
I mostly use a a double cap, 9 mm cap with 10-12 mm post length rivet. I get mine at Buckleguy, but wherever you purchase the rivets from you need the same setting equipment they sell for their specific brand.
@mabob59 8 ай бұрын
What machine do you use
@threadmodeembroidery2374 6 ай бұрын
I use an older Husqvarna tapaz 20 single needle with no cutter.
@coombslynn 9 ай бұрын
Please tell me what you have on your fingers and the purpose of them. Love your tutorials x
@threadmodeembroidery2374 8 ай бұрын
Hi, glad you like the tutorials. They are oval 8 ring splints for loose ligaments. They stabilize the joints :)
@dulcienel401 9 ай бұрын
What tape are you using. Not the double sided tape but the other one you use. I use masking tape but your tape looks lighter. 😊.
@threadmodeembroidery2374 8 ай бұрын
I use some medical tape, the paper kind when I can get it. It is thin and doesn't stick for me at all. The plastic style medical tape works too which is what I see in the video.
@salliemcd 9 ай бұрын
Thank you, this is quite amazing. I had no idea that something like could be done in the hoop. Do you use a thicker than normal needle? The card pocket sides look to be quite bulky.
@threadmodeembroidery2374 8 ай бұрын
I typically use an 80/12 ball point, only because that is what my machine likes to stitch with. For the cotton materials I sometimes switch to an embroidery needle. The card pocket itself isn't that bulky, however the whole pouch can get bulky if using thicker material. I prefer using cottons with a SF101 interfacing ironed on.
@lildebs1986 9 ай бұрын
Now that I've done it once, I think it'll take me less time to make again! Thank you so much for this amazing file!
@rosaleebertucci7 9 ай бұрын
How do I order this pattern.😊
@threadmodeembroidery2374 8 ай бұрын
The patterns can be found on Etsy or on the ThreadMode Embroidery website.
@kristibrooks5585 11 ай бұрын
May i ask where you git your design? I love it.
@threadmodeembroidery2374 8 ай бұрын
This is a design digitized by ThreadMode Embroidery. It can be found on the ThreadMode Embroidery website.
@DistortedLinds 11 ай бұрын
You didn’t say what was already in the hoop, help??
@threadmodeembroidery2374 8 ай бұрын
If you are asking about stabilizer, I use a tear away x2 for this design or a cut-away.
@margaretmurph3609 11 ай бұрын
Is there a video for the inside elastic pen holders
@threadmodeembroidery2374 6 ай бұрын
I don’t quite understand which elastic you’re referring too.
@afran7855 Жыл бұрын
I was meant to watch your video. I was looking for a golfing gift to sew for a friend and clicked on your video. Then I noticed your finger braces, and I knew what they were because I use a couple myself, then I noticed your thumb/wrist brace? Omg! Can you please explain this device and tell me what it helps and where to get one.? I have recently developed horrible pain in the base of my thumb down to my wrist, and it’s hindering me from doing what I love. My fingers get locked in the bent position and my wrist hurts so bad, my finger joints hurt so bad as well,but I have no idea what’s causing all the pain. I was told I have a trigger finger and possibly carpal tunnel, but definitely no arthritis. So I just suffer and cry myself to sleep most nights in pain. I’ve been using a couple finger braces on both my middle fingers, and using compression gloves all the time and ace bandages on my wrist and thumb on right hand, also been sleeping in wrist braces for last 2 years. Anything you could tell me about your devices and any advice to help the pain or what to get my doctor to look at I would be extremely grateful. ❤. Also thank you for the instructions for the golf ball holder. It’s adorable.
@threadmodeembroidery2374 8 ай бұрын
Hello, sorry to hear you are dealing with hand/finger pain, it is no fun at all. The ring splints are for loose ligaments as my fingers and thumb bend to far backwards. The thumb splint is not for the wrist it just keeps it in place better with that wrist band. They are from Digi Splint.
@steviecraftyhands3353 Жыл бұрын
Thanks for sharing your inspiration I brought the design after watching this video ❤
@threadmodeembroidery2374 8 ай бұрын
Thank you !
@margaretmurph3609 Жыл бұрын
Good Evening how long is the elastic for the loops and the holder
@patriciapenry9456 Жыл бұрын
I have just bought the pattern, love your video! Will give it a try tomorrow.
@threadmodeembroidery2374 8 ай бұрын
Thank you. Hope the stitching went well.
@mona1949 Жыл бұрын
Just purchased. Can you give instructions on adding the grommets and what size strap you made. Thanks.
@threadmodeembroidery2374 Жыл бұрын
Hi it’s been a while so I’m not sure the strap size but it’s a standard strap length. I typically make them to be 3/4” to 1” width and the grommets were a 1/2” inch size.
@mona1949 Жыл бұрын
Love it.
@mona1949 Жыл бұрын
Thank you
@Kaithorpe78 Жыл бұрын
How do I had the bean stitch to a design already made? I’m loosing my mind over this lol
@threadmodeembroidery2374 Жыл бұрын
Hello, you need a digitizing software to add any stitches. The bean stitch is also called a triple stitch and all digitizing softwares have them installed.
@vickieq33darnell99 Жыл бұрын
where would you get your shape for your fob. want to do a "class of 63 for class rejnion
@threadmodeembroidery2374 Жыл бұрын
I digitize all the designs manually, and they're not from a template. So I make the exact shape I need. You require a digitizing software to do that.
@saheedabiona6340 Жыл бұрын
Where can will get these paint
@threadmodeembroidery2374 Жыл бұрын
I get them from Buckleguy, but there are many sources, just do a search from your favorite leather suppliers.
@1234grolsch Жыл бұрын
What are the scissors that you use please, the ones with the extra bit of metal on?
@threadmodeembroidery2374 Жыл бұрын
I am not exactly sure what scissors you are asking about, but I think it may be the pinking sheers.
@tammycoles9728 Жыл бұрын
How do I get the instructions for the materials needed for this project?
@schisandra Жыл бұрын
Link to purchase pattern is in the description
@lindadavis6193 Жыл бұрын
Would oli fun material ok for back
@threadmodeembroidery2374 Жыл бұрын
I’m not sure, I have never tried that.
@lindadavis6193 Жыл бұрын
Could you use 2 layers cut away stabilizer or maybe decovil
@threadmodeembroidery2374 Жыл бұрын
I don’t think that would work well as the markers get onto the sides and back when kids are using them.
@sharon-z Жыл бұрын
Will this work with the very thin floppy vinyls that have fuzzy or felt backs? I have tried a coupl of times but the little threads/ fuzz keeps poking out from the sides. Granted, i can see now my technique was not on point. Thank you.
@threadmodeembroidery2374 Жыл бұрын
I use the floppy vinyls as well and I just use a lighter along the sides to remove any threads and fuzz. It is harder on the thinner vinyls but it can work. I use some cardboard taped onto the vinyl pieces so I can hold them straighter.
@sharon-z Жыл бұрын
@@threadmodeembroidery2374 thanks!!
@kathypruitt8651 Жыл бұрын
What is the size of pattern? Thanks.
@threadmodeembroidery2374 8 ай бұрын
The pattern has 3 sizes and it depends on the hoop size as to what the dimensions are.
@24carrotgold8 Жыл бұрын
🐇The bunny makes me smile 😊 but bunnies don't have pads on their feet 🙃 2023 is the Chinese Year of the Rabbit. These would have sold well with the year under their feet. 2024 is the Chinese Year of the dragon. Make some of those for next year 🎉👍🎊🐉 🐲
@threadmodeembroidery2374 8 ай бұрын
Thanks for the tid bit of info on bunny feet. They are there because most embroiderers want them for cuteness.
@saraalicea3363 Жыл бұрын
Very interesting m, thanks for sharing it ❤
@blancaestelarodriguezberzu3348 Жыл бұрын
Que bonitos