This worked perfectly. Thank you.

Well done 👏

How long is the timing belt. Could u please tell me

Called a camshaft seal. Theres another one on the side of the timing belt.

Thanks bro life saver

I swear the camera man fucking sucks

Excellent video! The strip to the left of the bill that reads "100 USA" responds to UV light as a pink strip.

SeaFoam is a 100% Miracle Do-Nothing, except remove Money from your Wallet. It is Naphtha and a very Light/Thin Oil 70% Rubbing Alcohol, is already mixed with water, which makes up most, if not all of the remaining 30%

I use ground walnut shells- available as reptile bedding at the pet stores. Works much better than sand because it’s lighter so it stays suspended, angular for grip, absorbs the paint unlike sand so it adheres better and doesn’t flake off. No joke. Try it yourself.

what year is it?

P0603

top fuel line bolt is standard lefty loose the bottom one is inverted, i also had to grind down some of the fuel filter to fit into the brace

Thanx...I see the vid is 12yrs old...thanx anyway..looking for TBI parts , return fuel line has a barbed fitting and regular fuel hose..would like to make it stock /not gerryrigged...any sources?!?

Got a question on a murano 2011.

Thank you brother, gave me the answer I was looking for

mine is giving me an error for broken IAT2 - but i can't even find where that is - 2,4 ecotec

Thank you sir! I was getting an AIT code and checked Google for a replacement and it was showing me MAF sensors, now I know!

When I turn my fan on above two I lose my heat it goes cool ? Would this be a solution or does anybody have a suggestion?

So you're telling me, I can't do this job myself without a lift?

It's only one blend door for 2002 avalanche. Thanks

11 years later thanks bro

Thank you for this tutorial video. I especially like that you showed the headlight bulb replacement number. Thank you.

Very useful, thank you. I wish I had the tools to do this myself.

Only correct tutorial out there 👍🔥

I have an 07 Chevy Aveo LT 1.6 l. I have to replace my Crankshaft gear. Is there a video that can help me with that and with my alignment and info on if a press is needed or a puller to remove my Crankshaft gear. I would appreciate any help.

The FIX for mine was a a new tbi/injectors and a new boshe fuel pump. My fp pressure was 8lb (too low) and the tbi injectors had a wet spray not mist. The fp pressure should be 11-12lbs. I tried EVERYTING alse first and nothing fixed it. Not even the cts.

Thank you so much

Best scientific improvement of compression, using RESTORE on KZbin!

0:30 vacuum line is OK ... 0:35 vacuum line now snapped .. how did that happen? you broke it ..

You are not using the correct sockets. You need impact sockets so your test is completely invalid. Sorry.

Hello, 12 years late, lol i have an issue with a 92 g20 van 350 tbi it's not running rich but a very high idel, and someone was telling me that it's the temperature sensor

Damn i definitely remember this commercial lmaoooo i miss this so much

When you turn the key to the on position make sure it’s on the first on position not second on position.

i had hard time both with removing flex disc and separating driveshaft from the housing so i used 550c industrial blower,3-4 cycles of heating and banging with a screwdriver and it broke loose

Wheres your passenger side video

After new injectors, I only have .6 volts at each injector harness. What's the correct voltage with key on?

Thank you! Saved me big time!

Thank you

Literally was on the side of the road . This was saved me thank you!!!

The first tool you will need is a vacuum. Oh, and a 10mm socket with extension for the back seat removal. Your seat should have been bolted down but it wasnt

Thank you. The only other video shows removing the top motor mount, the crossbar, the top and bottom aluminum housings over the sensor. After I got it out, I noticed the 10mm screw and thought that would allow the sensors removal. You show that it will. I am wondering if there is any point to removing the plastic housing in which the sensor rides (assuming it is not broken).

Now dont get me wrong,this is a great video,the only problem i have, is you used wire nuts.I dont think you should use wire nuts on those wores,too much resistance.You are better off using either a butt connector or solder the wires. Wire nuts are also known for coming off or letting the wires come out.Other than that though,your video was awesome and better than any of the other videos on here

I literally watched five of these videos and you're the only one that says watch out for the airbag never even thought about that appreciate the heads up

Hey guess what else will cause the code to appear. The timing chain breaking 😢😢

Great video Cody Hank’s lot bro you are save me a lot I time 👍🏻

5hakns 8

No crank no start?

Had the guide pin bolt brake off, but I was able to find it easily on the parts store. I came to this video specifically to know where the low brake warning tab slid on 👍 great video

guess the real way would be tooo pump it out of the tank as it will just rust inner lines

👍❤️❤️❤️❤️❤️❤️