Mine didn’t come with directions so I’m trying to figure out the correct order of washer/locking washer used to connect the rack to the brackets..? Your video didn’t actually explain anything. 🤷♂️”bolt it together and put it on top” like obviously. Would love to have seen the directions you flashed the camera one time to.
@5150MotorSports3 күн бұрын
Lock washer always goes next to the nuts…
@jimmiesmith420820 күн бұрын
Whats the Mishimoto part number for the radiator you installed. Where did you buy the radiator?
@jeremyhanna385227 күн бұрын
1:42 the either bunny took it
@grantparnesАй бұрын
What is available for just the "middle" of gladiator? I don't need a full set but would see benefit to the breakover area for High Centering.
@joeylopinaАй бұрын
That was awesome to watch. Good job guys. 👏🏽
@65dalexanderАй бұрын
I'm thinking about just installing Nemesis front fenders only, i dont see a significant difference betweeen the back and factory units, and would save me changing out my factory bumper, which I like.
@Madmike908Ай бұрын
Clamp the bar on and use the correct size drill bit for the nutsert would’ve probably been a lot less work.
@Madmike9082 ай бұрын
Does the windshield fully seal with and fold back up properly without any modification even with the rockhard cage kit?
@5150MotorSportsАй бұрын
Yes, no problems, thanks for watching…
@Madmike908Ай бұрын
@@5150MotorSports cleanest JL build on KZbin so far. Simple and capable. Keep up the good work.
@ekbanjosworld49262 ай бұрын
I like your videos! They show how it REALLY is doing this work! I'm 62, I just did this! I don't want to do it again! Getting too old to be crawling around under these jeeps! 3 days to recover from a half day of work!!! I did both front and rear brackets...
@miket732 ай бұрын
This helped me out because I was missing my handle but I took a tube and smacked the end of it and it works
@bobhauck31042 ай бұрын
On your CHIRP file what are all the SEA channels associated with?
@averagejoe82132 ай бұрын
What's the tow capacity of that bumper?
@CRTRUCKING1132 ай бұрын
Great job.help me a lot with my project.thankmypu
@luistrevino6543 ай бұрын
Its been 3 year but what numeration is on the front springs?
@JoseOrtega-xn4mj3 ай бұрын
Can you mix 2 or 3 bottles to be ready or not recommend?
@5150MotorSports3 ай бұрын
I don’t see why not, but very easy and quick to mix. Thanks for watching.
@tonykrempin72593 ай бұрын
How does it look after 4 year? Sun fade? Peeling? Would you do it again?
@markc62074 ай бұрын
how is this bumper holding up?
@miketheis534 ай бұрын
Why are you wearing such a nice shirt while you're mixing paint? Did your wife kick your ass later?
@obxjeepguy4 ай бұрын
Wow. An old Roll A Long Custom F-350 just like mine! Also, too bad Banks stopped making these headers. I was going to do the same thing to mine.
@albertlevinson21584 ай бұрын
Rugged GMR25 is not listed on chirp menu, what would be compatible to program? Or is there another software program to program? Thank you!
@egman52254 ай бұрын
You might have been getting high beamed because of lift ? Maybe, great video I'm about to do the same on my stock 21 Rubicon
@AUCRATECH937224 ай бұрын
Can you add privacy channels. Our off road park uses 17-25 on a rugged radio system. Thank you.
@bpchristensen4 ай бұрын
what axle seals are you using that are "way more reliable" than the MOPAR units?
@rickypalomares97864 ай бұрын
Well, how is the cage treating yall after a year of running it?
@5150MotorSports4 ай бұрын
No complaints, working great. Thanks for watching.
@reebertJunkman4 ай бұрын
SUPER GREAT VIDEO... How good a painter does a guy need to do this, can a NEW BEE with a lot of rattle can experience do this? I have a good compressor....
@NorEastBeast4 ай бұрын
Nice Jeep man! What color did you use?
@jimmysoliver52595 ай бұрын
My 05 is losing coolant. I found water in the turbo any advice on what's causing this. It also runs hot when I have a load on it
@ericwheat95405 ай бұрын
I would like to get me one of these.
@pedrog42215 ай бұрын
Hello. After removing the stock bumper, what is the estimated installation time, including electrical assembly???, thank you.
@5150MotorSports5 ай бұрын
Thanks for watching, a couple of hours…
@andyw48495 ай бұрын
Just watched your video after deciding to go with tnt front fenders since I already have their sliders. I plan on going with the 4.5" fender for a little additional coverage. Just curious how they are holding up and if you would go with them again. Thanks.
@5150MotorSports5 ай бұрын
Sweet, These thing designed well are stout, haven’t had them out yet, just finishing up the new paint job, hopefully have it out at KOH, next week.
@vincentmamotos99375 ай бұрын
gonna stick with steel skids.
@TwoFeatherChannel5 ай бұрын
excellent idea, thanks.
@Nigriff6 ай бұрын
My 2000 Cherokee uses size 20 torx
@jamesmoore11246 ай бұрын
My inner bags were broken and I lost a few but I bought them with more than was needed.
@elancastell45596 ай бұрын
Did you need a resistor for the led indicator?
@MJJCvideo6 ай бұрын
@5150 MotorSports Good repairing video,may I know if it's ok for you to review our foam cannon S V3.0?Thanks in advance!☺
@samwalker13046 ай бұрын
Wow! Nice XJ! Please look at the Holly retro headlights. Can’t stand the look of the cheap lights😂
@JoseOrtega-xn4mj7 ай бұрын
Is this the first time you do this? If so good job 👏 I’m going to do my Dodge Ram 2500 and watching as many videos as I can. Any regrets or recommendations? Thanks 🙏
@chuckbarnes99187 ай бұрын
Don’t waste your money on this bumper. It’s so weak that I can’t carry a 33” spare. So I don’t carry a spare and it’s so weak that I can’t even use the 2” receiver. I called EAG and asked them if they had any kind of extra support brackets to help hold the bumper up and they said no. I told them that they need to engineer something better because it’s dead weight that serves no purpose. One of the biggest wastes of money you can throw away
@dougtweedy707 ай бұрын
Looks like a bunch of newbies had a great day! We all had to start someplace. The main thing is to get started and amaze yourself what you and your jeep can do.
@bmitchley41897 ай бұрын
Two part question But I just purchased a new UV-5R and followed the steps everything worked perfectly. But now I’m the radio isn’t talking like saying “frequency” when I power it on nor is it giving me my “custom” welcome when I power it on. Is there something in the settings I need to change to fix these? Is it true that I won’t be able to transmit on any of the channels now with the new radio updates?
@baysiderecords55827 ай бұрын
Would it be the same for a Grand Cherokee? Same engine.
@5150MotorSports7 ай бұрын
As long as it’s a 4.0 should be very similar!!
@harryperrone66268 ай бұрын
Bulb orientation and"clocking" very helpful. Thanks
@don-po10628 ай бұрын
Got a 1995, in the same position crank/no start. It sat for a year or so before i got it. So far i have replaced the distributor and rotor, fuel filter, fuel pump, fuel pump fuse, new battery (old one was doa), and all 6 spark plugs. Even though all of that didnt work to start it still needed it. A pretty hard newbie over here, anyone got any ideas?
@castledomeknives93957 ай бұрын
I would replace the crank position sensor.. it is a very common problem ... look up a video on how to test and replace it ... I'm sure you'll find some here on KZbin... good luck
@derikgg9655Ай бұрын
Try wiggling the wire harness to the top left of the valve cover gasket. Mine cranks but as soon as I wiggle while somone cranks it will fire right up.
@jeremyhanna385227 күн бұрын
Cps
@sacjusticeforyou8 ай бұрын
Good lookin rig bro!! Long-live the 2-door!!!
@jrosetothedome8 ай бұрын
solid video... but can we talk about darth vader behind the camera 😅
@AZHighlandHomestead9 ай бұрын
very smart. earned my subscription :)
@crazytestpilot94349 ай бұрын
Could I just manually enter the frequencie of the rough radio chanel??
@5150MotorSports9 ай бұрын
I don’t see why not… Thanks for watching…
@westside_tints81979 ай бұрын
As a window tinter of 10 years not bad at all for your first try.
@DJ-kn5ff9 ай бұрын
Thanks for the installation video. A body shop installed bumper during a repaint of my grandson's XJ. We need to pull it off and check the install as the rear bumper is very noisy going down the road. Rattles like crazy and sounds like it is going to fall off every time you hit a bump. May be that it is just too heavy for an XJ to handle or could be slop in the construction of the swing out bracket, but we need to make sure it was installed correctly. Regarding the license plate, we were able to drill and tap three 1/4-20 holes in right side of tire mount for a license plate bracket. Worked out real well. The third brake light is clearly visible above the tire, so there was no need to add an additional brake light. Enjoyed the video. Great job. djbnola