Пікірлер
@sajadmohammedbaghdad5526 11 сағат бұрын
Great job
@YiannisPagonis 11 сағат бұрын
Thank you my friend 😉😉
@Timo-Epis 15 сағат бұрын
this sound is his signature lol
@YiannisPagonis 11 сағат бұрын
🤔🤔
@igorsmartinovs6571 2 күн бұрын
добрый день ,можете подсказать. Заменил левую переднею шаровою, когда стал закручивать гайку на самой шаровой где вставляется фиксатор, гайка закрутилась заметно ниже, фиксатор вставил, но он выше гайки. После замены шаровой, левое колесо смотрит в лево, что бы его выровнять руль нужно повернуть на 3 часа вправо, в чём может быть проблема? Шаровая по каталогу подходит на мою машину
@YiannisPagonis 2 күн бұрын
Если вы просто поменяли только шаровой шарнир, то вся сборка могла сесть неправильно, если было заменено не только шаровое соединение, то теперь могут быть и другие изношенные детали, которые все еще нужно заменить. После замены всех изношенных деталей может потребоваться полная профессиональная регулировка.
@igorsmartinovs6571 2 күн бұрын
@@YiannisPagonisа как она могла сесть не правильно? Шаровую вставил стал затягивать гайку в виде короны она стала шаровую подтягивать, если бы я за крутил не много до того где фиксатор вставлять, при езде шаровая бы стучала , так как она не прикручена, где две гайки и болт на шаровой там всё подходило чётко
@mainethings 2 күн бұрын
09 212k oil changes every 4to8k. Never serviced and still running fine. Wait till you replace alternator to service
@BabyGangsterIsMe 2 күн бұрын
I never clean it.. Toyota selenoid last 150-200k.. just buy a new one to replace it after 150k, it is not that expensive... also, it will save time in a long run
@YiannisPagonis 2 күн бұрын
In a typical combustion engine application, a starter solenoid may undergo approximately 30,000 actuations over a 15-year vehicle lifespan. Start/stop technology can increase this figure by a factor of 10 or more.
@BryanKennethM 4 күн бұрын
Love the music! 👍🏻
@YiannisPagonis 4 күн бұрын
Thanks my friend kzbin.info/www/bejne/bKbHaX6Bltp1ldk
@mpakalis_power 5 күн бұрын
Αποτυχία το έκανα και οι βίδες που έβαλα μέσα έπαθαν οξυδωση από το υγρά και κόπηκε πάλι ο ακροδέκτης
@YiannisPagonis 5 күн бұрын
Φίλε μου μάλλον κάτι δεν έκανες σωστά στην όλη διαδικασία και για αυτόν τον λόγο δεν πέτυχε. Μήπως τις βίδωσες στραβά και βγήκαν έξω από τον πόλο της μπαταρίας; Πόσες βίδες έβαλες και πόσο μακριές ήταν;
@mpakalis_power 5 күн бұрын
@ έβαλα Τρεις βίδες πέντε πόντων δούλεψε κάνα μήνα και μετά κουνήθηκε ο πόλος και είδα τις βίδες να έχουν λιώσει από τα υγρά και οι τρεις
@YiannisPagonis 5 күн бұрын
@@mpakalis_power Κρίμα και λυπάμαι για αυτό! Τώρα το πρόβλημα σου έγινε μεγαλύτερο μιας και έχει φύγει περισσότερο υλικό (μολύβι) από τον πόλο της μπαταρίας. Δεν είμαι σίγουρος αν αυτό τώρα μπορεί να επισκευαστεί!
@Metalpriest62 5 күн бұрын
Άψογος!!!
@YiannisPagonis 5 күн бұрын
Ευχαριστώ φίλε μου 😉😉Το έκανες μόνος σου; Πέτυχε;
@elsiervoamistoso 6 күн бұрын
This is a great video unfortunately for me I needed to remove the whole assembly that it seems to be latching underneath the radiators but I don't know how to remove them yet
@andrewzibuck5860 6 күн бұрын
Awesome, thank you. My daughter got a gadget with multiple chargers but it didn't fit with the gearshift in park. Took the little door off, and that was enough room.
@YiannisPagonis 6 күн бұрын
My friend, it's best not to make such interventions for safety and aesthetic reasons.
@andrewzibuck5860 6 күн бұрын
@@YiannisPagonis eh, it’s 15 years old with 240,000 miles. It’ll be OK.
@YiannisPagonis 6 күн бұрын
@@andrewzibuck5860 Let's hope everything goes well!
@clevelandrocksdzd 6 күн бұрын
Nice job, but way easier to pull the fuel pump fuse and let the car run out of gas that way.
@YiannisPagonis 6 күн бұрын
I did it my friend but without any result! What a pity!
@starlo.s7606 10 күн бұрын
Greeks do it better
@janicejohnson1334 10 күн бұрын
(ENGLISH ) the 4 bolts that secure the center cosole in place . . what size millimeter are they
@YiannisPagonis 10 күн бұрын
My friend they are all 10 millimeters (mm)
@robbie5817 11 күн бұрын
Thanks for the video. It gave me the courage to repair the left hand turn signal led which was broken myself. Removing the needles is the scariest part. I did not use tape since the displays cover that area anyway. I used two slim trim tools without the 1mm shims, that worked fine. Putting the needles back is tricky to align, as the motor can move and has no fixed zero point without power. I had to make slight adjustment to get the needle of the speedometer at zero.
@YiannisPagonis 11 күн бұрын
Well done my friend, good effort. Did everything go without any problems? Was your problem fixed?
@robbie5817 11 күн бұрын
@@YiannisPagonis I bought another cluster from the junkyard since they are so cheap. I first disassembled that one and remove a SMD led. Then I opened the one from my car and swapped the broken SMD led for the other one. It fixed the problem so everything is working now again. I only had an issue that the needle for the speedometer was not positioned correctly. I had to take that off one more time and then I was able to align it correctly. Thanks to your video it was relatively easy to do.
@YiannisPagonis 6 күн бұрын
@@robbie5817 Very good, smart and impressive what you did my friend! It seems that you can do a lot more things than you think! God be with you!
@Chapita7 12 күн бұрын
No entiendo para que quitaste la tapa trasera. Creo no tiene sentido sacarla
@danielperu4 13 күн бұрын
great job !!!! thank you ..... Muy buen trabajo , gracias
@YiannisPagonis 11 күн бұрын
You are welcome my friend 😀😀De nada mi amigo
@mpampisstavrianopoulos9334 13 күн бұрын
Καλησπέρα έχω καί εγώ τό ειδιο πρόβλημα μία ερώτηση με τόν καθαρισμό υπάρχη περίπτωση νά μου τό βγαλη στην καμπίνα
@YiannisPagonis 13 күн бұрын
Καλησπέρα. Τι ακριβώς θέλεις να μου πεις φίλε μου;
@YiannisPagonis 13 күн бұрын
Κανονικά όχι. Δεν υπάρχει μια τέτοια περίπτωση
@CarlosMolina-y6f 14 күн бұрын
What are the parts number ?
@giancarloalmodovar9731 16 күн бұрын
That car is from 2003-2008.
@ph3733 17 күн бұрын
Great video. Helped me a lot. I still troubleshoot to get the gear side aligned as the knob didn’t have the full movement after install. I solved the problem by pushing the large white wheel for the heater control and the small white gear for the temperature control into one end position (anti clockwise) and then turned the knob into one end position before clipping the gear in. If this didn’t work I moved the knob into the opposite direction. Now they travel to all positions. I was quoted $1,200 to get this fixed. $35 for both cables on Amazon and 1 hour later the problem was fixed.
@YiannisPagonis 16 күн бұрын
Well done my friend, well done and I'm glad you did. I can tell you are very good at what you do.
@CarlosMolina-y6f 17 күн бұрын
Hola amigo donde puedo comprar esas partes las mecesito para mi Corolla 2011
@Mac7Los 19 күн бұрын
This is really annoying and freaking stupid... taking out the speakers with out explaining how to get to the speaker by showing how to remove the god damm rear speaker "cover panel... god damm stupid as hell. Stupidstupidstupid for real.
@agustinalvarez6127 20 күн бұрын
You tested using 12 volts, isn't it?
@YiannisPagonis 18 күн бұрын
Yes it is 12 volts
@danymartinez2863 21 күн бұрын
Fallaron los americano tengo un Toyota Corolla 2012 y eso se ha roto dos veces ya esa manilla es muy frágil se rompe mucho
@YiannisPagonis 21 күн бұрын
Afortunadamente ninguno se rompió en el mío. Fabricado en una fábrica en Sudáfrica.
@rahi7339 22 күн бұрын
hey do you know how to replace CDI? my bike is not starting, before it was turning off atutomatically at low speed or at stop. now when i try to start the odometer screen and all lights flickers on/off, help bro
@josefranciscoesquertalaman3827 22 күн бұрын
Excelente video de el selenoide vvt, presente en Navojoa Sonora México, gracias por compartir
@ΔημήτριοςΠατουλιός 24 күн бұрын
Κ. Γιάννη καλησπέρα, τώρα είναι να βάψω οροφή και αυτά θα βγουν. Τα έριξα μια ματιά δεν είναι ιδιαίτερα ξερά. Ήθελα όμως να ρωτήσω πως μπορεί κάποιος να καταλάβει ότι θέλουν αλλαγή;
@YiannisPagonis 24 күн бұрын
Καλησπέρα φίλε μου Δημήτρη. Εάν είναι ιδιαίτερα σκληρές, ξεραμμένες και έχουν αποκολληθεί κομματάκια από αυτές τις πλαστικές λωρίδες οροφής τότε ναι έφτασε ο καιρός να τις αλλάξεις. Η υπερβολική έκθεση του αυτοκινήτου στον ήλιο καταστρέφει αυτές τις λωρίδες.
@ΔημήτριοςΠατουλιός 24 күн бұрын
@@YiannisPagonis ευχαριστώ πολύ
@YiannisPagonis 24 күн бұрын
@@ΔημήτριοςΠατουλιόςΠαρακαλώ φίλε μου. Να γνωρίζεις ότι το κόστος της κάθε γνήσιας λωρίδας είναι 47 € (από την αντιπροσωπεία).
@salahdin6596 25 күн бұрын
Hello dear friend.. Why not bleed the clutch, which is the same circuit. The bleeder screw is the same as that of the brake bleeder. So you haven't changed all of the brake fluid.
@homeintheozarks 26 күн бұрын
Great video, thanks for explaining how to take off the nozzles. This was really helpful!
@YiannisPagonis 23 күн бұрын
Thank you and you are welcome my friend 😊😊😊😊
@braydenstoch-wv4uq 26 күн бұрын
Great job good experience
@YiannisPagonis 23 күн бұрын
Thank you and you are welcome my friend 😊😊😊😊
@dogukanbalki2110 Ай бұрын
Can we use WD40 for cleaning spray ?
@YiannisPagonis Ай бұрын
WD-40, gasoline, or carburetor cleaners are the solutions to help remove and clean the oxygen sensor effectively. Soft brush to remove “stubborn” dirt. Soft towel: dry the sensor after cleaning. In addition, you should also prepare extra gloves and glasses to avoid getting stuck with gasoline and cleaning solutions.
@dogukanbalki2110 Ай бұрын
@YiannisPagonis thanks for help brother, regards from Turkey. 😊
@YiannisPagonis Ай бұрын
@@dogukanbalki2110 You are welcome my friend, regards from Greece, too.😊
@irenemmaguire Ай бұрын
Thank you so much for this video. Especially how to re-adhere the clip on the car roof!! Which is exactly what happened to me when trying to remove the old trim!! 😄
@YiannisPagonis Ай бұрын
Thank God. You can do it yourself?
@irenemmaguire Ай бұрын
@ Yes, just waiting for the temperature to get up enough to use the adhesive! It’s 26F this morning - way too cold!😉
@YiannisPagonis Ай бұрын
@@irenemmaguire Great. Once the temperature rises then you can start the replacement. I wish you every success in your project 😉😉😊😊
@irenemmaguire Ай бұрын
JB Weld SuperWeld Light-Activated Glue worked perfectly. 10 seconds and the adhesive was cured in 40F temp! KZbin is not adding the pic.😊
@YiannisPagonis Ай бұрын
@@irenemmaguire Well done my dear lady you did very well and I am very happy for that. You deserve 100 well done ☺☺😊😊 www.google.com/search?q=JB+Weld+SuperWeld+Light-Activated+Glue&rlz=1C1GCEA_enGR1053GR1053&oq=JB+Weld+SuperWeld+Light-Activated+Glue&gs_lcrp=EgZjaHJvbWUyBggAEEUYOTIICAEQABgWGB4yCAgCEAAYFhgeMggIAxAAGBYYHjIICAQQABgWGB4yCggFEAAYgAQYogQyCggGEAAYgAQYogQyCggHEAAYogQYiQUyCggIEAAYgAQYogQyCggJEAAYgAQYogTSAQkyNTMzajBqMTWoAgCwAgA&sourceid=chrome&ie=UTF-8#fpstate=ive&vld=cid:fcbdd4b9,vid:iin4GmsxfLM,st:0
@marcoscosta1116 Ай бұрын
Vídeo top
@YiannisPagonis Ай бұрын
Thank you my friend 😀😀😀😀
@supersarbun8902 Ай бұрын
Thank u man , god bless u
@YiannisPagonis Ай бұрын
You are welcome my friend, God bless you too
@Timo-Epis Ай бұрын
do you have a fix when these pillars keep coming lose when driving?
@YiannisPagonis Ай бұрын
Check and replace damaged clips
@landonohlinger2708 Ай бұрын
I'm confused about why you unhooked the battery remove the seat messed around back there with the fuel pump put it all back together again after you hooked up the gauge and everything and then when you took the gauge and everything off you didn't take the battery cable off and you didn't remove the seat and you didn't mess with the fuel pump wiring. Was that all an accident or something wiring
@YiannisPagonis Ай бұрын
My friend, this entire process had to be done for safety reasons so that the fuel could first be decompressed from the fuel line before the final fuel pressure test was done.
@leninayala-bey7728 Ай бұрын
This is not helpful at all, how do you remove the damn lever without doing all that
@YiannisPagonis Ай бұрын
Unfortunately my friend all these tasks must be done according to the Toyota technical manual
@TheStarGhost Ай бұрын
I know this is an older video, but I wanted to thank you!!! I had watched other videos trying to show the same thing but they just weren’t clear enough or helpful. We managed to fix our temp control knob thanks to you! I’m sure it saved us a pretty penny not having to go to a mechanic!
@rubensllanes2685 Ай бұрын
Excelente Tutorial
@YiannisPagonis Ай бұрын
Muchas gracias mi amigo ❤❤❤❤❤❤
@simonburns1055 Ай бұрын
good tip with the silicon on the O ring bro
@YiannisPagonis Ай бұрын
Thank you very much, my friend ❤❤❤❤
@krasiangelov6195 Ай бұрын
super
@YiannisPagonis Ай бұрын
Thank you my friend ❤❤❤❤❤❤
@simonburns1055 Ай бұрын
Make sure to use your brothers toothbrush as he never uses it anyways lol
@YiannisPagonis Ай бұрын
Sharing a toothbrush within a couple can lead to the transfer of oral bacteria, including those associated with periodontal diseases. Moreover, if one partner has a dental infection or oral health issue, sharing a toothbrush can exacerbate the problem or spread it to the other partner. lol 😁😁😁😁
@giorgosparaskevas2648 Ай бұрын
Τζάμπα ελυσες τον θόλο
@sulemanmuhammadakram2808 Ай бұрын
Sir toyota corolla 2009 1.8 engine automatic transmission sir drive to stop signal rpm dropping Less than 600 sir clean throttle body maf sensor even changed throttle body but problem not solved plz help us sir what should I do
@YiannisPagonis Ай бұрын
Step-by-Step Guide to Diagnosing and Fixing RPM Drops: Step 1: Inspect the Idle Air Control Valve. Step 2: Check for Vacuum Leaks Step 3: Replace Faulty Spark Plugs. Step 4: Clean/Replace the Throttle Body. Step 5: Inspect and Replace the Fuel Filter.
@hermanmiller3708 Ай бұрын
This will be of tremendous help to those faced with predatory repair shops quoting $thousands to do this replacement.
@YiannisPagonis Ай бұрын
I agree and add to that, my friend.
@nuriakpinar5394 Ай бұрын
corollanin direksiyon kutusu icin bir video yaparmisin
@stephaniestone3305 Ай бұрын
It's not that easy when you put a brand new one in there is that easy when you put the old one out put the old one right back in but it ain't that easy with a brand new control arm
@YiannisPagonis Ай бұрын
Maybe you're right in what you're saying, my friend.
@Harley_Quinn1986 Ай бұрын
Hola amigo sigo tu canal, tengo un problema, al comprobar la varilla de nivel de aceite, tiene un poco de olor a gasolina, ¿que tipo de averia puede ser? es un piaggio liberty 125 abs del año 2018, gracias amigo que dios le bendiga
@YiannisPagonis Ай бұрын
Hola amigo. Una posible causa es la fuga de combustible, donde la gasolina ingresa al aceite debido a un inyector de combustible defectuoso, regulador de presión de combustible o una línea de combustible dañada. Otra posible causa es la combustión incompleta, que puede ocurrir cuando la mezcla de combustible y aire no se enciende adecuadamente en la cámara de combustión.
@Harley_Quinn1986 Ай бұрын
@@YiannisPagonis muchisimas gracias por la aclaracion, que dios le bendiga
@raiderman28 Ай бұрын
Excellent
@YiannisPagonis Ай бұрын
Thank you my friend ❤❤❤❤❤❤❤❤
@allans7281 Ай бұрын
Words do not need to be spoken to best tutorials are the ones where you just simply watch Nice I love this liberty 150 with the Faco tinted windshield at the top case it’s nearly perfect USA