I got a question. My garmins turn on at the same time when one is powered on.. my lowrance hds units dont and need to be turned on independently.. but i do have the yellow wires connected from the bow and helm unit.. cant figure out why they don’t turn in st the same time..

Thanks for the help! Just switched from humminbird to lowrance and it’s a whole different ballgame with the set up.

How did you get your 3d to show trees . Your picture is clear .I'm running a HDS live 9 .

Where did you put the train horns on the truck

Paul I am new to waypoint navigation. I actually got lost on a big lake and it took me forever to find the boat ramp lol…. I saw how you navigated to your waypoint with the trolling motor . Do you have a video navigating to a way- point running the boat ? Can you explain it like you did in this video ? I know it’s probably easy but I am very new to this . As much detail would be greatly appreciated.

if you want to add a dish to that boat, I know a guy! LOL

I know this video is old but I have a question. I know you said front units, under vessel make heading global. Should that be same for console units or should they be local? I hope you get this and again thanks for all the great info.

I really like your videos. I have used them alot. Thanks for putting them out there.

Awesome video. I could do this with just one unit on the console correct? If I had a 3-1 and hdi on the back?

Thanks for help Best regards Stefan Håkansson Sweden🇸🇪🇸🇪🇸🇪

Can you split the screen to show sonar/maps pages along with the HDMI page or the whole HDS 16 screen is occupied by the phone's sharing?

👍🏻 Awesome info

Are you using the C-Map withing the unit, or are you using a chip for Maps? The Navionics chip i have for the great lakes does not really give any better detail. As a matter of fact its worse then the C-Map in some areas on Lake Michigan.

How to connect phone to carbon to watch game ? thank you

Does this same process but with iPhone work same as well?

Hello great video. I am having a problem with my unit reading 57 degrees F when our outside temp is at 90 degrees F. It is a Lowrance Gen 2 12". I just swapped out a Gen 2 9" that was working fine. I have the boat on my trailer and the sonar stopped. I am also seeing this on the bottom left. I am using a HST-WSBL transducer, and unfortunately don't have a manual. TIA What I see on the bottom left of my screen says , 1 unselected when in the Sonar from settings.

In general, the TI units are faster in response to inputs. This is seen when quickly switching between sonar, downscan, chart, and split screens kzbin.infoUgkxeAxH15LxhjGlg5-CRYqjTGTEH0tbY4vk recommend The Hook units will show some lag on button pushes and screen switching. The big ticket item though is maps. If you install a mapping card such as Navionics or the free C-Map Genesis which has a lot of map detail, then moving around the map with the cursor or when running down the lake can lag significantly on the Hook units, but is seamless with the TI units.

There are not that many 500lb or larger snap swivels on friend. kzbin.infoUgkxUggREp1Kytzg8CpXMHFtlfQp4bskrIuy In fact I only found two. So I purchased both the (500lb) and the American Fishing Wire (600lb) units. When My order arrived the 500lb snap swivels were inside a bag that was labeled "250lb test", which caused some momentary concern. I contacted to make sure my 500lb 10/0 swivels were actually 500lb test. responded promptly and explained the miss-marked package. These 500lb snap swivels utilize .080" diameter wire that, despite the size, is still fairly easy to open with your bare hands. The ball bearing swivels are a thing of beauty and roll smooth as glass. So how do the AFW snap swivels compare to the snap swivels? Well, there is a 100lb test difference so the only uses .080" wire, and the snap is significantly longer, which combine to make the snap easy to open with your hands. The AFW 600lb snap is so stiff, and short, that most people will need to use a pair of pliers to open them. Also utilizes ball bearing swivels whereas the AFW swivel is a plain barrel swivel. I frankly like both units and cannot decide which is better, so I made half a dozen leaders out of 49 strand 7x7 stainless 600lb cable I also got from AFW and I am going gator hunting. We will soon know who is the master of 500lb plus snap swivels.

Can i mount my Active target transducer to the transom of my boat for salmon jigging in salt water ? And if so how would i mount it ?

Good Vid man, but do you know if Lowrance unit will support 4K ? If not I'll buy the cheaper lower rez version of adaptor. Thanks

If the trolling motor is flipped the other way, so the prop is out, then is it OK for the transducer to be just the opposite of what’s in this video?

I installed mine active 2 backwards lol

Hi Paul..I have a guestion... I'm mounting a point one on my new sea pro center console bay boat.. the power to the nema network only activates when the switch is on so when the key is off, Iloses gps signal from the point one.. do I need to set up a separate power source on an aux switch?

How do you add boat docks to your mapping

Hi I changed my temperature form global to local and it don’t show me temperature in sonar source only depth . How I can put it back ?

Wondering can you use any other gps puck antennas with a Elite ti 9?

I'm having that issue stepping on the trolling motor to lock it in. I used all the shims that came with the motor. I'm just confused on the leveling part. went out to the boat and used a leveler...it looks level to me, am I doing something wrong?

Paul, for some reason I don't have the stow feature on my Lowrance Ti2 9. Is that part of the Ghost update or the unit software?

Do you have a viedo on wiring up a HDS 12 and active target....I need it to be ridiculously simple...like ok boys and girls hook the red wire to the battery like this......I watch a couple viedos and decide I can do it and when I get to my boat and see 3 or 4 cable ends with wires that need to be splice I draw a Blank...I feel so stupid

Do you have a viedo on wiring up a HDS 12 and active target....I need it to be ridiculously simple...like ok boys and girls hook the red wire to the battery like this......I watch a couple viedos and decide I can do it and when I get to my boat and see 3 or 4 cable ends with wires that need to be splice I draw a Blank...I feel so stupid..I knownInwant a switch on the yellow wite sonI can cut power to my box and ducer and the main unit stays on

I have a new Carbon unit and set a new waypoint. Then, I accidentally hit Go To and the route from my house to the new waypoint appeared. How do I delete that ? Thanks....I enjoy your videos.

Can 1 AT2 module show the Scout mode only or the forward facing mode only with the Lowrance Live or Pro head unit?? Then do you just manually adjust the module for the other view?

How do you get sound to work if you don't have speakers in the boat right when I connect I get the video on my hds live but sound cuts out

Anyone know how to do this with an iPhone? And not an Android phone

I just switched over to Lowrance HDS Live 12 from Garmin and this video saved me hours of frustration.

Awesome video. Can't wait to try the measuring tool.

Keep up the good work and good luck on the tour

I’d like to see the sleeve come down farther on the blank

Always enjoy your content

Can you use the HDS unit to connect to stereo speakers? My 2015 has a recently fitted 12” HDS Live unit fitted. In doing so the previous owner removed (and then lost) the radio/stereo head unit. So I have the speakers and the HDS unit. Is there a way of connecting the speakers to the hds or do I have to go and buy a new stereo head? Thanks in anticipation a rare Robalo owner in the Uk 👍🏻👍🏻

Cool. Why??

So you have to have a sonic hub to view video on carbon or live? Even if you don't need sound

Paul, I have a Lowrance HDS 9 gen 2 touch at the bow and a HDS 12 Gen2 at the console, they are networked thru etherernet and named each graph. When I go to split 2D sonar windows, both the windows show either the 9HDS or the 12HDS but "not" one on each window. If I'm at the bow, I want to see what's going on in the back transducer and the front transducer at the same time but my graphs won't allow that. Why? I've seen other videos where you can do that but none explain how too

Ok...It was the cable! Bought the Microsoft cable and follow your instruction ..and it works! I have to figure why i don't have the sound. I'm doing this in my office, not on the boat...so I assume that sonar has to be blue toothed to boat radio. Anybody has any knowledge on this subject?

super video! I was looking for your video I watched few days ago, where you're talking about $100 USB to HDMI cable...I ordered USB to HDMI on Amazon(cheap!) and today instead the previous video I found this video and follow your instruction. Unfortunately don't have the Microsoft screen. Is it possible that the cable is bad? Do I need 100 bucks cable? Electricity for Both HSD's Live12 is from 110V to 12V adapter on my desk..Red and yellow wires are twisted together. Please advice! Thank you so much. Love yours instructional videos!

Nice! Oops, just missed that fish lol

Question, are you using Ghost 360 with your active target? If so can you tell me about the wiring of the system using both?

I don’t understand how turning on the audio system mirrored your iPad to the finder. Shouldn’t it just mirror when you select the source?

I've been trying to find out if Active Target connects to Ti2 12"???

Thank you for the info - It helped me with my new system,