Setting up Dual Point 1 Antenna's

This video shows u how to set up dual point 1's and the settings u need to change and the app u need to download.
contact me [e-mail] for questions

[@quietyourmindfishing]

Thanks for the help! Just switched from humminbird to lowrance and it’s a whole different ballgame with the set up.

[@erniesanders3724]

Amazing information Paul and well presented. I would have been lost without this tutorial. Can't thank you enough.

[@dallasdain]

The distance variations makes it a challenge to find those previously marked pieces of cover and structure. I wish I could find the magic formula to tell me to add or subtract that 9'-18' variation. Best tool I've found is a c-rig :) Great info again! Keep these coming, please!

[@BASSANGLER7MH]

Thanks man!

[@agentwynnoutdoors]

Wondering can you use any other gps puck antennas with a Elite ti 9?

[@PaulGettysFishing]

What others are you thinking about it would have to be nmea 2000, and there are multiple from lowrance

[@deemoney916]

do you have a video on this info but for a humminbird? This video is phenomenal - AWESOME AWESOME AWESOME

[@PaulGettysFishing]

No sir I don't, sorry

[@DaleWyman]

I ran across an issue the other day with two HDS LIVE units connected to a NMEA 2000 network with a conected Point-1 and the Calibration process did not work from the Console mounted HDS LIVE. The Heading, Pitch & Roll options did not show up from the Console HDS either. I did not think to try the Calibration process from the Bow mounted HDS. Both units had the latest software update. When I tried to initiate the Calibration process from the Console HDS, the rate of turn that you would normally observe just stayed at 000 and I never got a "Calibration Complete" message. Have you ever encountered this?

[@meme330212]

Hello!! I would like to ask a question about point-1! When I installed point-1 on my elite fs9, and was ready to calibrate, I found that the rate of turn was already 5-6 degrees, but my boat was tied to the shore and didn't move! What is the reason?

[@jerrykohler7089]

Paul, thanks for the channel. Could you tell me the name of the app that you used please? Thanks!

[@PaulGettysFishing]

Magnetic field detector

[@jerrykohler7089]

@@PaulGettysFishing thanks; they must have discontinued that app. There are others. Thx

[@jerrykohler7089]

May have found it for 0.99

[@jbranham50]

So using the second (rear) point-1 is a more accurate gps reading than the internal gps on the unit? I’ve never seen this before so I’m setting here questioning why dual point-1. Thank for sharing.

[@PaulGettysFishing]

yes u are marking within a 1ft of the transducer of what you are seeing, if you are a weekend fisherman 1 will be fine this is more for the tournament angler

[@jbranham50]

Awesome! Great knowledge sharing! There goes another $250.... lol

[@scottd8753]

I got a new Ranger and the factory already installed point-1 on bow. I have 2 HDS Lives, one on bow and ine on console. Should setup be: both units global for heading; comsole unit on This Unit for GPS; bow unit on local Poimt-1 for GPS location?

[@bassmadnessboricua708]

I already calibrated the front unit i need to calibrate the one in the back how do i do it

[@daveoconnor2588]

I see you have multiple units. Probably 3d module and all of the trimmings....looks like they draw a whole bunch of juice. What batteries do you use? Brand, How many, Group size, type? Thx.

[@PaulGettysFishing]

I run 5 lithiums Relion is the brand 31 series I have a cranking battery and the house battery than 3 for the TM

[@daveoconnor2588]

@@PaulGettysFishing house battery and cranking battery wierd in parallel ? Thx.

[@PaulGettysFishing]

@@daveoconnor2588 on a switch /charger isolation valve the motor charges both i can use 1 or the other or both

[@chazt4863]

Totally confusing!

[@PaulGettysFishing]

Very simple, just stop and watch and follow instructions