Thank you! One of the best instruction videos I have seen. 👍🏻

That engine must be quite worn out. Befor I went to work for GM testing Detroit's for compliance with EPA emission standards, I saw them in Awry Bakery trucks. Back then they had an ether "pellet" to use on cold days. Later I saw Cummins 250's that had a can of ether mounted right on the engine for cold starts. I can tell you that if this was a normal starting 6/71 when I was testing, it would not be certified for sale. But, I am a purist at heart, that is not pollution, it's unburned Diesel fuel and maybe engine oil, not the same as a gasoline Hydro Carbon, Co or Nox emission at all. Most of it is particulate and it falls out of the air to the ground. I personally would keep using it if it clears up after it gets hot hot hot, and I'd use starting fluid and maybe even propane to get it up and running on cold days. But, that sound!!! Somewhere on youtube there are two trucks that someone recorded as they drove by, one is a 4 cycle and the other a Detroit 2 cycle. There is no comparison in sound, the 4 cycles sound like Helicopter flying by with it's chop chop chop, then comes the Detroit, M M M M M M M. It's really amazing when you hear them one after the other like in that video. I'll take the Detroit anytime and twice on Sunday over the 4 cycle chop chop chop, even if it did smoke. But, I tested them against a dyno for emission certification, so I have a special place for that sound in my heart. Thanks GM for allowing me to run your awesome prestigious Detroit's at the Milford Proving Ground Vehicle Emission Laboratory VEL, bldg. 31, it was a blast and I'll never forget it. ben/ michigan

I’m going to be honest, every time someone brings up the topic of living in a bus, I imagine a bus that’s all cramped and older. This is bus that I would totally live in! How much did it cost?

I80 in Wyoming? Maybe nebraska

How do you know when you are at valve overlap?

That's what i wake up if i forget to adjust my AC thermostat to higher temperature before i sleep😂

Awesome once again. Thank you

Awesome thx

Awesome

Super boulot très utile merci !

Good video with some whatever works engineering. Happy riding!

My marriage after one year in.

My old 1994 Toyota Camry V6 be like...

LOVE THIS

Does coolant go through the small fins that you straightened out?

How or where did you get your welder?

Another great Canadian success, un autres succès Québécois merci à vous deux génial

Félicitations pour le beau travail vous êtes vraiment manuel, ce qui vous fait sauver beaucoup de $$$ attention à vous deux bonne route

Sympathies à Mme Sylvie sa famille et à toi Yvan,nous surveillons vos vidéos avec votre Bus et votre compagnie DIY que j’adore j’ai tout vos produits 👍

Great idea! If there is already fuel pressure in the lines, would fuel pour out when trying to tap into the secondary fuel filter? I'd like to install this on my bus.

Lesson learned going green isn’t always a good thing necessarily .

My dad had these when I was a kid even a v8 in one great memories

Woah, I did not know that!

99% of the time Yvan can fix it

You can replace just the hinge and save yourself a load of bother.

✌🏽✌🏽

Older bus!? Lol mine is a 1961! Yours is new by comparison. Btw I hate wiring problems too. Its my Achilles heel.

How did you attach the long nut to the plate

Nice looking old bus! Great job on the conversion!

How i feel in a morning

The old nemesis green Crusted wires and connectors.

Why didnt you use the sponge? 😀

Hopefully the wiring wasn’t too bad to fix. That’s why y’all are the dynamic duo

That'd do it! (Whatever is broken... :) Either my computer's busted, or there's no audio on this short...

Been welding poly pro and pvc for years. Unfortunately I never knew of the pendulum method. Thanks. Don’t forget to leave the air on when you shut off the heat. Ask me how I know. lol.

Hi, just want to ask if you ever had a problem with the front tires airbags?

What about the original wiring for the bus? How do I know what not to cut from the upper storage??

Starts on 2 cylinders, then later on 4 and then all 6

I was expecting a Kazakh reporter

Great video series! Thanks, learned a ton. Maybe I missed it, but what was the thickness of plastics you were using? Also, where did you source your plastic? Somewhere local, or an online distributor? Thanks!

That's how people in Kazakhstan say hello.

😂 funny I should find this I'm looking to make a custom water tank for my mobile detailing rig

❤❤❤❤❤❤❤love you😘❤😘😘😘❤❤❤❤ oke suka👍👍👍👍👍. Engine 💨💨💨💨💨start cold exhaust💨💨💨💨💨💨💨 knalpot penis-penis yes 😊👍😊👍👍👍👍sangat puas👍👍👍👍

Great video. I bought a tank with no fittings installed. May I ask where you got your fittings ?

I received a violation ticket for using the Prevost’s J brakes. It’s not allowed in build up areas where I live, Vancouver, Canada.

I have a couple of questions for you, if that's ok. First and most important, now that it's over 7 months from your video, how has this air bag jack held up? Is it still working? Do you use it a lot? Secondly, I've noticed in your video and other videos as well that the instructions state, "Skirt of the car" for lifting. I"m not sure what that even means. When I first heard it, I thought it meant that you can't use this to lift via the front of rear center frame jack points. Yet, in your vid and others, people do life by the center jack points, like you did with that truck near the end. And the RV even. So do you know what they mean by the "skirt"? I take that as the trim and panels, which would make that statement in the instructions a bad thing. What is your opinion on that? I ordered the 3 ton version of this, with the solid handle (not the adjustable handle). I hope that it comes quickly so that I can change out the winter tires, lifting at the rear center then front center. LOL

Je l’ai fait mais la voiture ne se ferme plus à clé une solution ?

such fluffy puffy smoke love the huge tailpipe looks so warm and cozy

New subscribers sir, definitely very impormative..i have struggled setting governor and the rack, we got Detroit 6v53 model..