This was very helpful. It would have been great to see how your corners and final top piece go on.

Thank you gonna try it myself don't have the money for a pro 😮

Thanks gonna try it myself

You don’t use a nail gun?

THANK YOU, FOR THIS VERY HELPFUL DEMO/INSTALL VIDEO!!! MUCH APPRECIATED!!! [IMHO: YOU SHOULD ALWAYS WEAR SAFETY GLASSES, WHENEVER WORKING..]

I have been fighting these gutter splices for years. Every single time they fail and leak. Maybe this time I will lubricate the barely glued on seals on the inside so they do not peel back when you apply force to drive them in. Silicone fails every time, I even tried using vinyl glue to stop the leaking. This time I am going to use Loctite vinyl glue which seems to be recommended most often. I think the cure is just to use a different system that might cost a bit more.

I have the parts list, electrical drawings and exploded views in front of me and I only see one fuse in the listing. Also, the place number, 19, is not drawn anywhere. I'm pretty much certain many of those things called "fuse" in your video are actually sensors or switches ... The fuse listed is a very standard glass fuse. Parts: WG02F00564

Thank you

It looks nice. A bit of a disappointment as I thought it was going to be for small appliances. I think there's some tips I can use for my kitchen.

Waiting for completion. The only thing I would have considered is extending the sheetrock to the existing corner instead of the odd look of two levels on that one wall.

Muchas gracias me funcionó 👍

Great vid! The answers I was looking for.

What kind of loft did you use?

Nice boat thanks for the tutorial

Holy smokes. I think I can do this! Thanks!

Worked perfectly for Kia Sportage 2017. Thanks!

Are the KIA frame bolt holes threaded? If yes, what keeps the bolts from vibrating loose?

Thank you for explaining how to overlap the vinyl correctly. Having not done this before, it never would have occurred to me that the seams aren't visible when viewed from one angle versus another.

Hi, where can I buy this motorized shelf lifter?

So what if I don't want to nail each soffit and just add an F channel on the subfaica board and just insert them?

Great video

Where does the water go at the bottom of the window? Is it shed to the front of the siding or does it go behind the siding? I’m confused

I wanted to see how to finish on top

J Channel is used on almost all block homes in Florida. You cant install the F on a 2x2 nailer with Stucco. Fine on wood frame.

Do you alternate or scatter the joints so all are not at the same place up the entire wall? How do you do that? Like wood flooring of a 3 board spacing pattern?

Thanks for the simple and QUICK video. Showed the basics. Exactly what most people need.

thanks for the video instructions. i experienced the same problem and took the speaker off today . but then i decided to test it outside the car. when i connected it to another audio source suprisingly the speaker worked. so now i am confused whether to buy a new one or search for other reasons of this fault. i mean speaker works with other audio output but when connected to car it simply does not work. Can it be a bad fuse on the car that controls this hazard and signal light speaker? thanks

Could you please tell me the thermal fuse's part number? I cannot find it anywhere

This is stuff of legends right here 🔥🔥🔥

How did you open the speaker lid the video cut off, I’m really not trying to break anything.

For those who have this model or similar: Mine was dead, with no lights or display. I followed this gentleman’s strip down but when I looked in the top right hand corner, behind the grill, I could see a glass fuse but couldn’t find access to it by removing a panel, nor was I able to remove the grill. I ended up by cutting 3 bars off the front grill and was then able to remove the fuse which was glass and 20amps. (I knew the plastic fascia would cover over the cut grill) Tested it and it worked fine. Reassembly was straight forward. Thanks for giving me the confidence to attempt the repair.

Thanks for the great info!

What kind of screws did you use, how many (or spacing)? Also, how did you create the bevels?

Man you gotta be kiddin me! You are a Master at this. THANK YOU SIR!

Outstanding!

Thanks for the video! This is what I expected, but it's nice to have verification before diving into the unknown. 😊

Excellent! Look almost exactly like the job I’m doing, even the color. All the needed important info is there especially about looseness. No biography, just a quick slide show about your lifestyle. Very cool!

My luck I will drop the flippin screw

Eazy money

Easy. Easier. Easiest to follow. Good job guys!!!!

Thanks man. Very helpful

Thanks for sharing! This is just what I was searching for... 🙏

Thank you, just watched this video and have now changed my speaker, took about 10 minutes. tips for anyone else - The clips can be a bit hard to prise off, I used 2 small screw drivers and slowly went round the edge. This fixed my parking sensor beep, the indicators ticks and the welcome tone. I got my speaker from eBay for about £25

Thanks a ton for this video. Have this exact microwave, and an internal fan would constantly be running with the door closed. Replacing the top interlock door switch fixed it for me.

What do you do at the top? Where it meets the soffit

Great video! Thanks!

Thanks. Very helpful!

How did you determine the speaker was bad? Did you test the signal to the speaker before you went thru the replacement?

I ADORE how much info you could put into four minutes. Other videos take half an hour to say all this. (Although your Fishing at the intro was nonsequitur.)

YIKES! Sorry, man, but that's not even close to "Average Guy".