Vi que sobraron un cable cafe y uno azul sabras para que sirve y pregunta el amplificador de fabrica sigue funcionando

This is very similar to my 2012 tundra, made it easy for me to do, thanks for the video

Como consigo esas baces para sostener el estereo?

I got the wolfbox 900 pro. When wiring it like this will the camera power stay on when ignition off? I need it to stay on. Is the what the constant power wire is for?

Thank you!!!! Just installed a dash cam to my brand new 2024 durango R/T

Feels like u dont care if u scratch anything. Whould have been angry if someone worked that sloppy in my car. 😶

They all look like pink white wire to me 😂😂😂

Is the 2015 Durango fuse box only located under the hood? I’m still confused which wire to splice to hardwire my cam. I feel more confident doing it from the fuse box

Which one you installed?

No rear windshield?

How do you remove the bolts attaching the glass to the panel? There are two grommets but you mentioned bolts but didnt show it in the video so how could this help someone?

www.youtube.com/@ismailgurgel nice job, here is a link of a tint master that really helped me save time on removing the window sweep. for that highlander all you need to do is remove the two top screws only then pop the panel out on the top only and that gives you enough room to pull the sweep out without taking the whole panel off. its a time saver. this is not criticism, im just passing along valuable info that helped me be more efficient. good luck and keep it up

bro are u there

IG o algo ?

tendrás algún lado donde me puedo comunicar contigo

Yo te lo puedo vender, en qué ciudad vives?

Hola oye me podrías pasar el link de donde compraste el harness y el mount del estéreo pls

Excellent video. Did the job yesterday. I used a drill and 10mm bit to remove the melted plastic caps as I don't own a Dremel. Thanks.

Whats that screen you used I'm trying to get a nice screen for my mustang

I did this and new door handle stays loose and door won’t open from the inside 🥺

Will Korea made regulator work on US Built Elantra?

Nice work

Great video! I'm getting ready to repair my front driver door and I watched this a couple of times. Keep up the good work!

Thumbs up

Where did you get the little white clips to mount it I got some but was the wrong size

Hello. Can you tell me pls what kind/size of screws you used to place the panel back after cutting those plastic couplers?

Would it be harder to do it to a roll up window?

فك فرش خلفي 300c AMG

Lower music volume

Thank you so much. Excellent video. Very helpful.

'Promosm'

I did this job for a client and i dont know how much to charge him and great video btw very helpful

I mean, it’s your car but it was hard to watch someone alter a classic.

hey is this the 95-5703B radio kit? also what radio do you have what size does it take i ordered the kit but dont know what radio it fits

Can't even hold the phone right.

Hello I have a m2 rexing dash cam a 2015 dodge durango with no manufacturer back up cam how do I install it thank you...

Just fixed my driver side door handle I appreciate the video saved me $1,800

Are you near my shop? I can give you a quote on my website www.roadshopaudio.com

Was just wondering what that would cost in my new 4runner it's got the back but I'd like front too

Nice job 👏

I have a 2012 e350. Same issue happened. Is there a link you can post for purchasing the part or part number? The MB dealership says I need to replace the panel at $4000!

Thanks man u made me waste no money

I have done an ignition switch 8 months pregnant on a jeep, pulled a transmission from a suburban, replaced my mass fuel sensor, rewires my cut out Benz headlights and stereo, fixed my DSL (driver steering locking mechanism that my locksmith accidentally pulled programming my new key, all of these by myself but doing my door handle on my Benz was the worst job I’ve ever done I wanted to lose my mind it was awful. Watch videos people

Seems to be a common issue with the damn German Benz

Did you disconnect the battery?

Yall want me to tell yall the secret to this door and the white clip? Its all built to install in one piece quickly on the assembly line, the door latch and plastic piece going from the window reg to the door handle are all connected by wires and plastic parts THAT CAN BREAK IF YOU'RE NOT CAREFUL. Do all the stuff shown here except for pulling the white plastic piece loose (its not easy to line back up if you do like the video. Remove three torx in the door latch. One 8mm bolt behind a grommet above the latch and pull the door key mech out. Slide the exterior door handle back and pull it out. Theres a little connector when you pull the handle back that is meant to swivel towards you. Use a small screwdriver or pick to get that connector loose. Loosen the screw that was behind the exterior door handle a few turns and push the white plastic assembly in slightly towards the inside of the door, (theres a little barb that holds it in place in the door sheet metal). Slide that towards the front of the door and then the old regulator, door latch, white clip and all will slide forward, down and out of the door. Then you rotate the latch, clip and all off the old regulator, install that to the new regulator. Route the wires through the holes in the new panel. Put the door connector end in the bottom of door, and slide the reassembled reg and latch into the door lining everything up with the door handle holes and guiding the latch into place to place a screw in to hold it and reverse the disassembly steps. The handle connector is a little tricky to plug in but not terrible. Id make a vid, but it was my nieces car and I no longer have access to it to make said video. Nor the time to disassemble it to reassemble it yet again. That white plastic clip gave me fits until i came to this realization of a process. Its so much easier to do right doing it the way I'm suggesting.

Could I Just Buy Doors With Power Windows Already On & Install That Way ?

Thank you so much, I fitted a new handle on my merc today. Your video helped a great deal. I haven’t got a dremel so just used a sharp chisel to remove the plastic rivets. I purchased a box of fixing clips of various sizes just incase some broke and there was actually one missing! Took me about 3 hours as I had no idea what I was doing until I watched your video. Thanks once again from your English buddies across the pond in London 🇬🇧👊🏼

The cameraman fucking sucks

Tbh the battery should’ve been disconnected very easy to blow a interior fuse for the radio