Ed's Handyman Tips

Пікірлер

@andymeeh9129 7 сағат бұрын

You didn't show how the glass goes back in.😩

@rthomas275 21 сағат бұрын

What tire size did you go with?

@edshandymantips4862 12 сағат бұрын

@@rthomas275 went with 215/70r17 on rear. Good size for me, good clearance. The fronts are 215/50r17. Not happy with the low profile look. I was concerned about clearance but could have gone larger.

@rayoh2011 3 күн бұрын

Good job, Sir. Thanks for sharing.

@sneakytxvenom1579 8 күн бұрын

And part number for the oil plug ring as well! Thank you again!!!

@sneakytxvenom1579 8 күн бұрын

Thank you so much for video!!! I wish you would have shared where you purchased the filter and type etc!

@Artoconnell 10 күн бұрын

Decent Batt for these cars is now about 350 ish dollars. 250 low end, 400 higher end. YOWWWWWW

@user-ud7fk1bl4g 11 күн бұрын

What about the warning message (break pads needs to be replaced…) on cockpit display, will it disappeare after the pads are changed?

@edshandymantips4862 11 күн бұрын

@@user-ud7fk1bl4g Yes, if the pads are worn down to the pad sensor the circuit is completed and the warning will trigger. Once new pads are installed the sensor will not touch and the warning will go away. I would replace the wear sensors along with the pads since they now have been ground down.

@skipbayless7912 12 күн бұрын

Thank you very much

@user-cg9ly4wg2s 12 күн бұрын

Wiring in truck looks terrible

@edshandymantips4862 12 күн бұрын

@@user-cg9ly4wg2s yes! One of these days . . .

@user-cg9ly4wg2s 12 күн бұрын

Dash has three screws not two!

@Vo1000RRonin 13 күн бұрын

First time? 😂

@marckrems779 16 күн бұрын

When you disconnect the battery they say you loose every function of the car after new one is in how do you avoid that ?

@edshandymantips4862 16 күн бұрын

I used an inexpensive harbor freight trickle charger. See video kzbin.info/www/bejne/jIHRonqwpKqlmq8si=Ts-jzI4GjmD3R3Sn

@spades262 17 күн бұрын

Awesome can't wait to try when the sun comes up

@sauljaquez7138 21 күн бұрын

Very nice

@rf4215 29 күн бұрын

...but how well does the latch work using the inside handle?

@edshandymantips4862 29 күн бұрын

Drivers side works very good. Passenger side not as well but that door does not fit quite right to begin with. Both better than the factory.

@rf4215 29 күн бұрын

@@edshandymantips4862 operating inside handled feels crunchy and I have to return handle to closed position before closing the door.

@edshandymantips4862 29 күн бұрын

@@rf4215 is the metal rod going connecting the handle rubbing anywhere?

@rf4215 29 күн бұрын

@@edshandymantips4862 that's what I'm thinking but can't see shit. I cut out that metal at the end of the seen t connecting inside handle to latch. Still shitty

@darlenebiggs7850 Ай бұрын

Do I do the same with a I-Phone 8plus?

@JBarnes917 Ай бұрын

That nice of a truck and you have wire nuts under the dash? Like seriously?

@henryt9254 Ай бұрын

I would use propress instead of Sharkbite especially within enclosed plumbing.

@johnr2297 Ай бұрын

Hi, How much oil is lost during this procedure?

@edshandymantips4862 Ай бұрын

My guess is several ounces. Not much.

@johnr2297 Ай бұрын

Thank you 👍

@falcon5866 Ай бұрын

In the manual write 6.9 quarts,you add 7.5 quarts?

@edshandymantips4862 Ай бұрын

You are correct, thanks. I’ll have to edit the video. Good catch!

@josephekundayo6776 Ай бұрын

Buying a RX 350 real soon. Doing some heavy research before I buy. I’ll be sure to tell them to change it before purchasing.

@daryabaghdar4340 Ай бұрын

It was a great demonstration, thanks Ed for sharing it with us!

@def-supreme5409 Ай бұрын

4-Pole Quad Circuit Breaker

@azcharlie2009 Ай бұрын

I tried the same thing with needle nose pliers and stuck myself in the palm!!! Ouch!!!

@6434SUNIL Ай бұрын

Thank you there, for sharing this. Nice setup.

@momcilopucar8749 Ай бұрын

Your pads are just fine. I don't know why would you replace them?? They're about 30% used only.😲🦧👀

@georged4597 29 күн бұрын

I have a 2019 and i replace the pads and they squeak for two weeks then it went away

@robanderson4137 Ай бұрын

How many hours on that project? total cost?

@jackdasilva6327 Ай бұрын

How much difficulty did you have welding that seam with sealant you put directly behind and coming out of the front of the weld joint? Also..there is paint on both sides of that frame.

@edshandymantips4862 Ай бұрын

Good questions. I recall burnishing the front side down to metal. Did not have any problem welding it. Still holding strong.

@jackdasilva6327 Ай бұрын

@@edshandymantips4862 disclaimer. I do not pass judgement on other tradesmen's work. I believe more or less we have the same occupation. Is it broken? I can fix that.. but. My current process welding tabs on the inside and using 3/16 ss rivets to make the connection where your weld seam would be. Then galvi or SS "cleats" on the bottom. The only reason I do this is to avoid any potential fires from whoever installed the frame. Again, this is just my way (of many ways) to achieve the same result. Good luck out there good sir

@ab-kn1gg Ай бұрын

I got the 2008...great video! Thanks.

@Oldsmobile_Eric Ай бұрын

Hi Ed I’m in the exact same boat. I have .080” gap with no shims installed. I have a guy who offered to mill my block at his work. I’m hoping the same .200” will work for me as well. I looked up your starter and it’s for a 168 tooth ring gear like mine. I would assume I need to take the same amount off my 9509 starter block but don’t really have any way of knowing. My thinking is if the gear mesh gap starts roughly the same, and ring gear is the same size, I would need to move the pinion the same amount as the pinion is moving straight up against the same diameter ring gear. Guess I’ll find out if I’m right. Thank you so much for the specifics it helped me greatly.

@MobileProBarber Ай бұрын

Thank you for your time and doing this Video much appreciated

@PabloSerrano-rx3wx Ай бұрын

I tryne. To .explain it. In Spanish. Any way you can help

@Ray.H1564 2 ай бұрын

Wow a claw hammer and a nail, that's just the beginning of the things you did wrong please tell us your not a professional auto tech

@lawrenceman4328 14 күн бұрын

Link to your video. Thanks!

@TheVictoriousG 2 ай бұрын

Great vid. just got some new vent windows but the fitment on mine are way worse than yours and leave a big gap.

@ncmach1 2 ай бұрын

Damn vertical videos

@stoneyswolf 2 ай бұрын

This is what happens when you start poking at it

@setauket2022 2 ай бұрын

you are a perfectionist. love it.

@kencolas 2 ай бұрын

Thank you so much for the lesson.

@sylvainaudrey1647 2 ай бұрын

How do we play music from the phone then?

@edshandymantips4862 2 ай бұрын

I bought one of these Bluetooth adapters. Not as elegant as factory but it works: www.amazon.com/gp/aw/d/B07F2RTN5Z?psc=1&ref=ppx_pop_mob_b_asin_image

@nicoleelyne7929 Ай бұрын

@@edshandymantips4862 hi I have a 2008 rx 400 h, will this device allow for me to be able to play music from my spotify?

@marcoguevara3174 2 ай бұрын

Do I have to go with the proses like for the rear with the key???

@edshandymantips4862 2 ай бұрын

Only the rear axle has the parking brake that needs to be electrically unwound.

@simonleung9396 2 ай бұрын

UPDATED I appreciate you posting the video even though it wasn't the solution to your specific problem. My battery is new and I replaced the voltage converter / aux battery and it did NOT fix the issue. Back to Square 1.

@edshandymantips4862 2 ай бұрын

I can’t remember if I mentioned in the video a new main battery fixed the auto stop/start function.

@raydavis9261 3 ай бұрын

Milled mine too now works perfectly

@richardtaylor3762 3 ай бұрын

Hi, Did you ever get around to doing a strip down on this unit. In the UK the dealer wants $230 to diagnose the problem (it was on the dash), how hard would that be? The part is $231 I never ever enev asked about the cost to fit so all in I guess it would be $550+. I am wondering if I can strip and fix the component. What do I have to loose?

@reginatorres5386 3 ай бұрын

How many cabin air filters does a 2017 glc300 have? I watched other videos and they are showing it under the glove box.

@fl4shphotography 3 ай бұрын

Do you have to put the car in shop mode while working on the brakes?

@edshandymantips4862 3 ай бұрын

Rear brakes only. It unwinds the parking brake mechanism on the rear. I have a video on the rear pad replacement that shows the steps required.

@ryeonspencer6235 3 ай бұрын

Great video thank you

@matrosstv 3 ай бұрын

Hi Ed, thanks for a great vid. I own a GLC 250d and use non run flats. You have to deflate the air from your spare tire for it to fit in nicely.

@user-cg9ly4wg2s 3 ай бұрын

Were you still able to use your emergency brake handle?

@edshandymantips4862 3 ай бұрын

I did not have an emergency brake system on the truck when I got it. Since all the parts were missing and the truck is already heavily modified I installed an electric e-brake. I did a video on it as well.

@user-cg9ly4wg2s 3 ай бұрын

I hope you double flared your line connections.

@edshandymantips4862 3 ай бұрын

Yes, after a leak a friend asked me the same question. I went back and double flared all the lines. No more leaks! Always learning!

@outlawdperformance 3 ай бұрын

I don't normally comment on youtube videos but you, my friend, have done a great service and i want to thank you for it.

Ең жақсы KZbin

Пікірлер