Travis Geis

Пікірлер

@jdsomers 6 күн бұрын

Thank you so much! I followed this video and got my desk to work again!

@상관도인 8 күн бұрын

바둑판은 기본적으로 노랑색(금색) 바탕에 검은색 줄이 가장 좋다. 하양줄은 흰돌과 중복되어 시각적 으로도 좋지 않다. 또한 줄(line)을 바둑판에 새겨넣는 제작기법은 대국시 바둑돌의 타미(打味)를 없애게 되어 바람직하지 않다.

@007mcvan Ай бұрын

Hi, do you know where to buy this 2 buttons controller? it stops working and the problem seams to be in this box

@williamstead6354 3 ай бұрын

Thanks, you just saved me a lot of time and trouble. Your solution was so obvious that it would probably never have occurred to me;-)

@PassTime-mv9cf 3 ай бұрын

can you please provide your travis print one font

@smilesmile787 3 ай бұрын

nice video Travis. where is the source for CAN signal? Also can you share how you opened the case to access the motor?

@juicysuit7195 3 ай бұрын

Is there a reason you started in Calligraphr and didn't just do it all in FontForge?

@kobayashimaru8114 5 ай бұрын

The molex connectors on the bekant are definitely a weak point, especially the outer connectors. Mine are really loose and I've resorted to using a ziptie to keep tension on the connection. I think in future I will either hardwire everything or replace the connectors with something more robust.

@MoonMullins 6 ай бұрын

I didn't need to rough up the contact, I simply followed your instructions for how to reset my up/dn button. Success! Very easy. Thanks.

@zrq55 7 ай бұрын

Thank you sir, this video has sloved my issue as well 👌 greetings

@robertloo9763 7 ай бұрын

This fixed my issue. Thanks for sharing!

@roxanne3243 7 ай бұрын

What is this motor called? I have problem with my desk, it has dual motor. One works okay but the other seems stuck. 😢

@TheCdM1981 8 ай бұрын

With the new anker protectors. There’s a selector switch of surge protection or grounded protection. If the surge protection is selected the usb ports don’t charge. They Only work if grounded protection is selected. Doesn’t really make sense to me.

@Antiwasserstoff 10 ай бұрын

Is it even worth fixing at all? I've had a bekant for quite a while because i was on a budget and i wouldn't buy it again honestly

@Subsonic-g2n 10 ай бұрын

The woodworking and finding walnut is not an issue, but where do you find a laser cutting machine to be this accurate????

@rodgerhunter1591 10 ай бұрын

Get edge tx bro that way you spend all your time setting up a model don’t worry about using the model because you will never have time because edge tx has no flow and good luck finding coherent help The radio you have there works just fine but hey if you are that mad at your money there are plenty of overpriced transmitters out there that do the exact same thing as the at10

@ReefDudes 10 ай бұрын

What voltage power supply are you using? I see anywhere from 29-35v. Assuming a 36v would work given the range. Any chance it said anywhere internal which voltages it wants?

@travis-geis 10 ай бұрын

It's an unusual setup because the power supply voltage changes when the desk starts moving. I'm not sure why or how they set it up that way. I assume the desk can tolerate the higher voltage all the time, but I don't know if there is some kind of communication that would keep a different power supply from working with it.

@kobayashimaru8114 5 ай бұрын

I'm powering my legs directly with a DC source (12V battery). I had to use a step-up converter to change the voltage to ~36V to get it to work properly. I assume the original power brick ups the voltage on demand.

@rob10424 10 ай бұрын

Thanks for the video. I will try this on the weekend when I have the time to get everything off the desk! :)

@ClarkeLSmith Жыл бұрын

the first mistake: People should know that the way you are cutting these with your bare hands so close to the blade is EXTREMELY unsafe. Use a GRIPPER!

@demej00 Жыл бұрын

Build it next time using PVC foam - nearly indestructable.

@peterdaba6651 Жыл бұрын

I just got one its great only it sucks power like ??? the 2200 lipo only last 30 mins?

@john2914 Жыл бұрын

I wonder why you would write such a comment. You have no idea what you are doing at all, that is clear. This radio will last all day long with any assortment of batteries. Maybe get a job, and buy a new battery.

@PugPower23 Жыл бұрын

Any idea what the clamping voltage of this surge protector is?

@supersummermario Жыл бұрын

Great video, really helped me with my contra rotating propeller project for differential control. Thanks

@dominicfong6341 Жыл бұрын

Great stuff, thank you very much for the autopsy and expert explanation sir!

@nologification Жыл бұрын

AMAZING WORK!!!!

@DragonDreamVNY Жыл бұрын

Thank you. Luckily my was ok after the Reset (pressing and holding both buttons together). It was very new, barely used.

@jed2055 Жыл бұрын

380c for unleaded solder. Big tip . . . use leaded @ 350c

@traze_tank111 Жыл бұрын

Where can I get this

@Actionsceneclipz Жыл бұрын

I use this for my Rc truck my range is about 2.4 miles

@calehuntfpv480 Жыл бұрын

Yeah definitely tail heavy the one I built I flew it with a 3s 2200 mah all the way forward, hope you got it figured out :) I’m thinking about building another one and putting one of the new walksnail digital vtx in it and a fc running inav

@jackhargreaves1911 Жыл бұрын

Incredibly helpful. Thank you. I was doubting the health of my controller box as I couldn’t get the desk to level up and to rise on one side (no matter how many resets were done). But watching you made me realise it was the motor that was the issue. Long story short: once I lifted the motor I simply wound the leg with a hex key until it was at the very bottom (and thus level with the other leg). After that they worked in sync again.

@danieldekel8268 Жыл бұрын

It is actually a futaba 10 clone. same buttons, more options, looks owsome. if you didnt like this, you would not like the futaba 10 which cost 4X

@naraalvarez05 Жыл бұрын

By any chance do you sell any of these, looking for a 19x19. They look awesome!

@user-fault 2 жыл бұрын

батарея на 24V а двигатель на 16,8V это как? обман покупателя?

@YuvalPalomo 2 жыл бұрын

Nice place to fly

@greggeis6638 2 жыл бұрын

Looks so familiar!

@martinkirouac 2 жыл бұрын

Mine just moves a bit then stops. If I keep pressing, the table moves a little bit again. Maybe a blown capacitor ? Any ideas ?

@travis-geis 2 жыл бұрын

Mine had that issue when the power supply was faulty. I ended up getting a replacement supply under warranty, and that problem was fixed, but later on I encountered the issue in this video where the desk stopped moving completely.

@martinkirouac 2 жыл бұрын

@@travis-geis Thanks. Called and got a power supply as well. Took less than 24 hours for shipping.

@theDuckysaurus 2 жыл бұрын

Any chance you could share the files for the 19x19 grid that you used? I’m having trouble finding one!

@travis-geis 2 жыл бұрын

Hi! Sure thing, here's a link to the SVG: github.com/ottobonn/go-boards/blob/main/19x19.svg This repo also has PNGs of the designs!

@noahnotte3919 2 жыл бұрын

Hey man. I got one of these about 9 months ago and I’m having some trouble with mine but I’m not technologically inclined. Any chance you can respond to this and help me out? Thanks

@dulguunbayardorj6907 2 жыл бұрын

After reseting mine went down only one side, so I had to stop and open up and manually lowered the table to the lowest. Now I hear clicks when I press the down button only. Nothing happens with the up button. I tried resetting by pressing both buttons or the down button for 10sec. Any ideas to try?

@livesinalazywonderland4021 2 жыл бұрын

I really hate this table

@samwhite1975 2 жыл бұрын

i like the idea of this and looked at it myself. however, it doesn't look to have the makita battery 3rd pin that is used for overdischarge protection monitoring. the batteries don't include it. it can be something as simple as a n-channel mosfet if you are happy with low side switching. i 3d printed my own including high side switching overdischarge protection in the end. did the same for a makita battery bench PSU

@jed2055 Жыл бұрын

Sam, we aren't charging the battery just drawing current from it. A complicated protection circuit is simply not needed here. How do you think these batteries run drills, grinders, blowers, saws etc? Nothing special is needed for a soldering iron and a genuine Makita battery has protection designed into it. We don't need to complicate what doesn't need to be complicated. Oh, and it's nice that you have a 3D printer . . . lucky you. @RoccoFPV. Yep, I agree 100%. 350c all day every day for leaded solder. Might need a boost for unleaded solder. - It's a pita. The iron has a sleep mode so working temp drops down after a selected time. It's not like the iron is running at 350c while you fiddle with a circuit board.

@Blackincolor 2 жыл бұрын

thank you so much

@travis-geis 2 жыл бұрын

Hi everyone! Thanks for stopping by. I recently had more issues with my desk and wanted to make a correction to this video. The contact that touches the motor body was not actually the problem. Instead, the issue was a loose or faulty connection in the plastic connector that plugs into the circuit board. I unplugged that connector and reseated it and the problems went away. If you have reset your desk and checked the power supply and it still doesn't work, check your connectors and try removing and reconnecting them to the motor boards.

@joscelynblevins744 2 жыл бұрын

Travis, can you add more details regarding the plastic connector faulty connection from the perspective of someone who know little about electronics but can follow directions really well. 😏

@damienduddy8893 2 жыл бұрын

@@joscelynblevins744 I'd also appreciate a video perhaps on this fix. I am about to attempt replacing the motor with a spare I purchased online

@jackhargreaves1911 Жыл бұрын

Thank you. It would be so helpful to see that done (or simulated).

@kirstensmith1 Жыл бұрын

Hi Travis. Thanks so much for this. I'm having the intermittent issue you described initially. The desk goes up about 1/4 " and then stops. It will go down all the way, no problem. How do I check the power supply?

@travis-geis Жыл бұрын

@@kirstensmith1 While holding the button to move the desk, watch the light on the power supply. If it dims to almost invisible when you try to raise the desk, it's probably an issue with the power supply.

@IDECFilms 2 жыл бұрын

Thanks, I was not sure why my desk was not working. When you showed off the reset feature that was what I needed to fix it. Was worried it was a motor issue because the power supply was reading the correct voltage.

@PockoRC 2 жыл бұрын

does it have voice telemetry

@travis-geis 2 жыл бұрын

As far as I know, it does not.

@travis-geis 2 жыл бұрын

I highly recommend getting a transmitter that runs openTX / edgeTX like the radiomaster tx16s. Those radios work with many brands of receiver and have way more features for a similar price.

@mixgrab 2 жыл бұрын

@@travis-geis dont be silly, simillar price? tx16s is twice time more expensive

@travis-geis 2 жыл бұрын

@@mixgrab At least where I am, the RadioLink AT10ii is selling for $160, and the TX16s is $199

@doublehelix. 2 жыл бұрын

@@travis-geis Only the max version gets a bit higher price. The standart version it is ~$199

@CarbonGlassMan 2 жыл бұрын

I've been using my lipo charger as a power supply for mine. I've been running it at 15 volts and 5 amps. I just discovered it's only rated to do 2.7 amps. oops. It still works fine. I was having trouble getting battery cables loose from an ESC so I increased the volts to 21 volts and 5 amps. That got the heat into the ESC enough to get the battery cables loose.

@bigfil1981 2 жыл бұрын

I really wanted the UK version of this but I was worried the plug slots would be too close together.

@florinpandele5205 2 жыл бұрын

Just an idea: IF you plan to dis-assemble the desk, it may be a good idea to extend the cicuit wires to the motors and leave the circuit outside (or put it in a plastic box under the leg). This way you will not have to dismantle the whole thing again if the motors still work. Yes that means the hall sensor too ....

@62heliman 2 жыл бұрын

did you check you C.G. you said the tails was low, so to tail heavy. check you CG.

Ең жақсы KZbin

Пікірлер