Lizard Jump

Пікірлер

@deixaki- Ай бұрын

Thank you dude!!

@bradkashner 2 ай бұрын

Show how to check if 2019 Dodge furangon.. Is gett ing fule

@HereWeGoSteelers 2 ай бұрын

My Dad and I are going to be changing the expansion valve in his 2015 GMC Sierra sometime this week. Can you tell me if you put anything on the o'rings when you put your project back together such as oil/grease? Thank You

@ameliayuan 2 ай бұрын

We are a vacuum pump lubricant oil supplier who can provide 1:1 replacement of Fomblin vacuum pump oil: Solvay Fomblin Y LVAC 06/6,14/6,16/6,25/6 equivalent Our material can be used immediately and even mixed with remaining stocks.

@rolandvillarreal2687 3 ай бұрын

Thank you.

@AmusedDaffodils-mz5rw 3 ай бұрын

Is this is what leaks gas

@ferociousneophyte 3 ай бұрын

Were you able to see the parts number before removing? I can’t find the sticker on the PCM and am wondering if the previous owner removed it. I had the original dealer and parts distributor run my VIN and no one was able to find the exact module it needs. I know it needs a California emissions PCM. I’m just not sure if it’s with or without radio frequency.

@eddeleon4108 4 ай бұрын

Can you just disconnect the harness and the fuse for it ??

@heatherhoekstra6989 4 ай бұрын

Did you remove the safety bar before changing? If not, what is the easiest way to get to the 3rd plug? I’m short and it’s in a tight spot. Thx in advance 😊

@johngriffim8616 5 ай бұрын

Is there a filter inside the hi side line at the rear expansion valve?

@lizardjump995 4 ай бұрын

There is no filter in the line at either expansion valve.

@johngriffim8616 4 ай бұрын

Just looked, GM parts catalog shows a filter front & auxiliary for my '15 'burban.

@paulplauche7779 5 ай бұрын

Being a novice AC guy and jack of all trades/master of none for 30 years, I can honestly say you did an EXCELLENT job explaining and showing everything as well as addressing the correct procedure for filling with details. Great work!

@lizardjump995 4 ай бұрын

Thanks for the comment! And, thanks for watching!

@sameerzx6122 5 ай бұрын

if the rear expansion valve is cloged or not working well , does it effect the cooling in front ? i have 2007 denali .

@skrypture1162 5 ай бұрын

Yes it can, however you can purchase a block off kit to block of the back ac so that your front system will still operate perfectly, if you have an issue in the back but don’t really need the back ac it’s a good fix

@pareidoliarocks 6 ай бұрын

Great video! Thanks

@thecuss6817 6 ай бұрын

Very good video - comment from an experienced "non-professional" in Arizona !!!

@lizardjump995 4 ай бұрын

Thanks for the comment!

@QuentinNeill 6 ай бұрын

Top 10 video - nothin’ but the facts

@lizardjump995 4 ай бұрын

Thanks for watching and commenting!

@PeterB12345 6 ай бұрын

Does this replace the compressor bearing? I don't use my AC here up north, but now it squeaks and I suspect a bad bearing. Don't even want an AC but I need the pulley for the belt.

@danielchan5944 4 ай бұрын

you can use a shorter serpentine/accessory belt and bypass the AC pulley

@PeterB12345 4 ай бұрын

@@danielchan5944 I suppose as long as whatever I use has the same belt tension. I think in this case the routing wouldn't really allow it. I've since done the repair in this video and it wasn't too hard to do.

@TSC9129 7 ай бұрын

Fantastic video. Planning to do this job after i have parts store scan Abs module. My obd doesnt resd abs for the santa Fe. Question. I have seen afternarket parts of just the abs sensor allowing installation on to old hub. Would it be best just to replace the whole hub assembly with after market OE replacement?

@benjarvis8595 7 ай бұрын

Just had my 2015 Tahoe lt rear evaporator changed at a dealer and the rear is still blowing hot air and they can’t figure it out. (Probably out of hours and done dealing with it for free). The lines going in are not cold underneath and no water dripping from the rear drain at all. Any help would be appreciated!

@lizardjump995 4 ай бұрын

Is the front cold? And, is the air in the rear unusually hot? Like heater hot?

@robertlavasseur2088 7 ай бұрын

Mines an 98 and the bed bolted on different. But I just tilted my bed up in the front with pump jacks so it was at a 45 degree angle and it was so easy

@Joe-zg7rp 7 ай бұрын

Awesome man! I just changed my first starter :) Watched your video with my laptop on the engine...paused after steps. Took my time, some bolts were a bear but did it. Saved a ton o money on labour. Thank You. Keep it up...we need your expertise and teaching style.

@basturma27 7 ай бұрын

Thank you. Just finished replacing the sparks in my Crosstour 2012.

@Yelladog78 8 ай бұрын

Thank you for this video

@lizardjump995 8 ай бұрын

Thanks for the comment and thanks for watching!

@yeeeehaaawbuddy 9 ай бұрын

kewl, a video of truck parts, while talking about other truck parts. How helpful.

@lizardjump995 8 ай бұрын

Thank you for watching and commenting!

@chrisward1144 10 ай бұрын

Thanks Lizard Jump! Easy peezy with your simple and straightforward instructions. Saved me $75!

@lizardjump995 9 ай бұрын

Really glad this helped! Thanks for commenting!

@stevendoyle5768 10 ай бұрын

You motherfuckers are fucking worthless duh, duh, fucking duh… we need to know how to disconnect that line with no fitting. No self relief no connector just seems like some glue. …

@fredolfscott3406 10 ай бұрын

One of the best repair videos

@lizardjump995 9 ай бұрын

Thank you for this comment! Thanks for watching!

@HeatherSmith-x6e 10 ай бұрын

I'm a female without any natural mechanic talent, a friend was able to determine this is whats causing my AC to malfunction. I have an appt with AC repair mechanic, what can I say or be prepared with so I'm not taken advantage of? If you did this job, about how much would you charge?

@deniscantin9196 10 ай бұрын

Thanks !

@nickploszay2310 10 ай бұрын

There are two more screws on the bottom of the plastic cover. It will be much easier to remove the dog house with all four screws out. Move both seats as far backwards as possible put the dog house out on the lip of the floor and tilt the top up towards the windshield it slips right out.

@lizardjump995 9 ай бұрын

Thank you for adding this comment! Thanks for watching!

@veygazgurl 11 ай бұрын

Thank you this is exactly what i needed

@lizardjump995 9 ай бұрын

Always glad to hear it helped!

@weselkins7503 11 ай бұрын

Gonna loose you're religion 🤣🤣🤣🤣🤣🤣🤣🤣

@lizardjump995 9 ай бұрын

……and I absolutely did!

@vilisoniloloyasi5054 Жыл бұрын

Thanks for the video, good education greeting from fiji

@lizardjump995 Жыл бұрын

Hope it helped! Thanks for watching and thanks for the comment!

@artisturner Жыл бұрын

Do you have the reverse order video??!?🙏🏽

@lizardjump995 9 ай бұрын

Unfortunately I did not make that. Definitely something to consider going forward! Thanks!

@MegaHorse7 Жыл бұрын

Can you just replace the sensor instead of the complete hub?

@lizardjump995 Жыл бұрын

I would recommend replacing the whole assembly.

@exploringcalifornia9110 Жыл бұрын

What is the plug gap for that model?

@demonicstallion1259 Жыл бұрын

.044

@ForTheAverageAmerican Жыл бұрын

Will this problem also cause the tire pressure, brake, and hill assist lights to come on as well? The ABS and traction control lights came on first??? Please see my comment and respond??? HELP!!!

@lizardjump995 Жыл бұрын

Sorry I haven’t responded sooner….. this will absolutely cause these lights to illuminate.

@VictorFong-d3n Жыл бұрын

what is the cause when the compressor clutch has no air gap whether the motor is both on or off?

@هيمولوف Жыл бұрын

Greetings to you, my dear brother But I have a question Did you use the high-pressure line to fill Freon? Why? Others object to filling using high pressure... and they say filling Freon should be using low pressure Thank you

@lizardjump995 Жыл бұрын

Sorry this has taken so long but the answer is yes. You can absolutely recharge on the high pressure side as long as the the engine is switched off and the A/C is not operating. If the engine is operating and A/C is switched on the you must recharge on the low side only. If you recharge on the high side with A/C switched on and operating it could over pressurize the container and explode. Hope this helps! Thanks for watching!

@MrFishface5 Жыл бұрын

you missed one step. the filter screen in the high side line at that valve

@lizardjump995 9 ай бұрын

Thanks for that reminder!

@tgmediabelize7928 Жыл бұрын

I have a 2012 Crosstour...recently my cylinder 4-5-6 died. we changed the 6 ignition coils and it still did not help...what do u think it could possibly be?

@lizardjump995 Жыл бұрын

There could be a couple issues. Did you change the 4&5 coils? If so and you still have issues it could be an injector problem but all 3 at one time is almost unheard of. Could be a connector issue at the coils themselves. You could also run a compression test on those cylinders to make sure they’re all good. Outside of that could be a computer issue with the ECM but even that is doubtful. I would focus on connectors and possible injectors. Hope this helps!

@hambizzy30 Жыл бұрын

Gotta quick question i already know now imma have 2 replace my whole ac system...i have an 04 srx 3.6 cadillac had it for 7 years I noticed my clutch was barely engaging so I assumed it was burned out which it was so I figured just replace the compressor boy what a mistake it lasted all of a month cool air front and rear now my brand new compressor is the clutch is barely spinning doing the exact same thing but not as bad then I noticed the compressor started smoking just asking do u think I have a bad expansion valve or some kinda block in the system

@lizardjump995 Жыл бұрын

When you replaced the compressor did you flush the system? This sounds like the new compressor just had a catastrophic failure. If a compressor disintegrates internally the debris will contaminate the system. The system will need to be flushed before putting in new components. Expansion valve will have to be replaced too. Another thing is to add the exact recommendation of oil and amount. When adding oil to the compressor you need to rotate the compressor several times to ensure the oil is coating all internal surfaces of the compressor prior to installation. Then, evacuate the system and recharge with the exact recommendation or refrigerant type and amount. These systems hold such a small amount of refrigerant that the slightest amount either way could be detrimental. Hope this helps. Thanks for watching!

@hambizzy30 Жыл бұрын

@@lizardjump995 thanks I didn't install it.....sadly it was the dealership

@lizardjump995 Жыл бұрын

Hopefully the dealership did all these tasks which in any case should be under warranty through them.

@tree1885 Жыл бұрын

What size extensions to get the plug out I can't get my cylinder 2 out either I have too long of an extension or too short

@lizardjump995 Жыл бұрын

I think I used a 4” extension.

@GeorgeBailey-gk2lo Жыл бұрын

What if the return is broke

@lizardjump995 Жыл бұрын

Is the return line broken or the fitting?

@jeffreydronenburgsr.8224 Жыл бұрын

Very HELPFUL video. Thank you! The bolt removal behind the stabilizer bar at time stamp 2:14 was omitted from the video - I think because it's a major pain to remove and would drag out the video too long. I used a 9/16" box wrench (didn't have a 14mm wrench) and a bucket load of patience to loosen it and fingers to back it out. Reverse the process to reinstall.

@lizardjump995 Жыл бұрын

Thank you for your comment! You’re correct that it is a real pain to remove. Thanks for watching!

@patboily300 Жыл бұрын

Beautiful job. Very useful info. Can you specify the rivet size that you used? (diameter and grip)

@lizardjump995 Жыл бұрын

They were 3/16” diameter. Can’t remember about the grip but just get them long enough to go all the way through both pieces of metal. There is very little stress on them during normal mast stepping. Thanks for watching and commenting!

@sergiobarajasgomezSportvan Жыл бұрын

Amigo saludos desde Leon Guanajuato México espero no ofender pero si me gustaria hacerte una sugerencia, note en tu video que el caliper y el disco estan sucios yo tambien uso el silenciador de disco de freno de esa marca CRC pero segun las instrucciones antes de aplicar el producto a las pastillas nuevas o usadas estando en buenas condiciones se deben de lavar con el líquido para limpiar sistemas de frenos tambien de la misma marca u otra para garantizar el trabajo estos productos son muy buenos pero si vale la pena que antes tienes que limpiar el sistema antes de aplicar el producto. Saludos

@lizardjump995 Жыл бұрын

Hola León. I am using Google translate so i hope this is correct. No me ofende tu comentario. Gracias por decir eso. Tienes razón sobre las partes sucias. ¡Gracias por ver y comentar!

@tonystewart-q2u Жыл бұрын

How do you get the panel off

@lizardjump995 Жыл бұрын

Hello…..which panel are you talking about specifically?

@southernsaintmusic Жыл бұрын

Thanks for posting this! I had trouble getting to the top 13mm nuts from the underside, even after rotating the compressor as much as possible. Just a few notes from my experience with my 2009 F150 FX4: 1. I detached the inner wheel well liner like you did, but ended up not being able to do anything through that area. 2. FX4 will also require removal of the skid plate. 3. The top two 13mm nuts were challenging to access from underneath, even after rotating the unmounted compressor as much as possible. In fact, I had to use a flex-head ratchet to access the first one... and then I noticed the top nuts were accessible from above, directly behind the battery using a socket wrench with 18-in extension and deep 13mm socket. 4. I will never do this again!

@lizardjump995 Жыл бұрын

That’s definitely not a fun job! Thanks for the tips you posted!

@aaronemblem266 Жыл бұрын

So I’m having an issue when I build pressure it forces fuel out of the boot on top of the fuel pump…any chance you can tell me where the fuel vent or esim is located so I can replace or unclog it mine is 95 model year.. or would just having a vented gas cap be enough to relieve that pressure?

@lizardjump995 Жыл бұрын

I’m not sure exactly where the fuel is coming out but if it is a vent issue you could try a vented cap.

@mitchellmedina7167 Жыл бұрын

Thank you!

@lizardjump995 Жыл бұрын

Hope it helped! Thanks for the comment!

Ең жақсы KZbin

Пікірлер