Excellent job. Very understandable. Lol "it takes 2 to make a thing go right" 😅 I have my grandpa's multimeter and was trained as an electrician Apprentice, so i understand alot of your tutorial. Appliances are pretty interesting.
@jm99802 күн бұрын
So far my fridge has been working since 1996..... Damn....well built I guess!!! Today 2024
@jm99802 күн бұрын
Damn this sh=t brought back memories when my mother use to defrost the freezer...Lol...Yeah now I remember...You just woke me up... I always asked her why the f u doing this? She just stated get the f out of here and just go play....LOL....nah really she use to state so we have a working fridge and freezer... NICE!
@JustinAnnes4 күн бұрын
Excellent diagnostic video! I had an intermittent no glow igniter on a <1 year old Amana. All the components checked out ok. Thanks to this video, I was able to troubleshoot and determine the centrifugal switch was not working and found out that the connector was not completely locked in.
@96Duelfuel10 күн бұрын
Thanks for posting
@joeruttan219510 күн бұрын
Confused" You say flame cuts off after a few seconds? Mine is 3:06, then shuts off? OR, you say it shuts off after about 30 mins, and it could be this or that? That's confusing, and I think you have the answer? Do you, as it could be Sensors, Sensors, OR Coils, BUT if coils, only after a few seconds - VERY confusing? Please explain. Thank you for your video!! joe R.
@applianceassistant8 күн бұрын
Under normal circumstances, on high, the burner will heat the air to between 180-220° Fahrenheit then shut off until the air cools down to about 100 -110° and cycle back on for another burn. It should keep doing this for most of the cycle until the cool down at the end. If yours is burning for a little over three minutes and then cycling off, that sounds normal. Just keep watching and if you ever see the igniter glow and go out, without an ignition, then you likely need the coils. I hope that helps. Good luck!
@joeruttan219510 күн бұрын
Thanks for video, started out fine, BUT got too fast and confusing after that? Thanks anyway??
@williamthesoccerstar11 күн бұрын
Mine starts has the flame come on for a few seconds then shuts off with an error code of E01. It's a Bosch. I bench tested the flame sensor and it never opens. Could this be why or something else?
@applianceassistant11 күн бұрын
If the flame is happening at all it is unlikely to be the flame sensor. Those symptoms normally point at restricted airflow or a bad high limit temperature sensor. Good luck!
@doughelms55813 күн бұрын
The Citizen Kane of electric range repair videos! Magnifique! Four Stars!
@Voidpizza83813 күн бұрын
Gud am sir.can i have the prices of the ff: Stainwash ultra LHBI02 8.0KG Molex part #W1074665-0 MANUFACTURING DATE: 3-2-2018
@davelowman357415 күн бұрын
Everything about this including the resistance measurements is so well done. Thank you for making this video.
@gerrylight722915 күн бұрын
I would have saved myself a lot of grief if I had watched this first. Best tip.... check burner function FIRST! Do this before tearing the dryer apart.
@stratoleft15 күн бұрын
After doing some research on my own, it's called an EC-3 or EC-5 connector. Most notably used for Lipo battery harness. Which is it for this motor?
@leepoff21 күн бұрын
F30 and f71 are the codes I get, unsure of what to do lmao
@nanajoanne86729 күн бұрын
Thanks
@nanajoanne86729 күн бұрын
Thanks
@applianceassistant27 күн бұрын
My pleasure! Glad it helped!
@apocalypse934729 күн бұрын
Superb video. Clear and concise. Second time watching this. I have an old kenmore fridge and love it. A few months ago, the fridge was not cooling and had to throw away food. Ice was on the back wall. Watched several videos but that evening it was working again. Whew 😅 I am adamant about closing doors firmly and clean coils monthly. Yesterday it happened again. Had to throw away food. No ice buildup. Today, 24 hours later, it’s working fine again. All my ice packs are frozen. Could this be the defrost thermostat intermittently failing? Thanks for sharing your knowledge. Peace love and blessings 💫
@applianceassistant29 күн бұрын
Thank you! You may be expecting an intermittent issue with the defrost control device. It’s pretty rare for frost to come and go like that. I would also look at the evaporator fan motor and any airflow control device that may regulate air into the fresh food area, that may be periodically failing. That’s a strange one! Good luck!
@apocalypse934728 күн бұрын
@@applianceassistant Thanks brother!
@RawFitChrisАй бұрын
Went to the website and searched "deconstructing the dryer" but "Not Found" came up. How do I see the video on taking the dryer panels off (particularly the front panel(s)?
@applianceassistant29 күн бұрын
Thanks for the comment! This video shows how to open up most of the top lint trap dryers. kzbin.info/www/bejne/qKq6iaGZrd6Uadksi=viNpSf9_Ar4phX-n Good luck!
@FullrusherАй бұрын
I'm so scared to do these simple things lol I undid my connections junction power box thing from the dishwasher and discovered the wires melted into each other , I'ma cut them back and reuse the wires but may check to see if the other end of this is connect to a 3 switch and single socket junction box above the counter, any advice ?
@applianceassistantАй бұрын
Being thorough is good! But in most cases just trimming back, the copper ends and replacing the wire nuts is acceptable when you find connectors like that.
@Gvdbelt-fh2mkАй бұрын
Great video, thanks very much. The only thing I missed is how to test and replace the valve if the coils are not the problem
@applianceassistantАй бұрын
I should have covered that! It’s very rare for the valve to need replacement. It’s pretty straightforward, just disconnect the gas line and the bracket that the valve is mounted to and swap it out. If you need to reconnect any pipes use some yellow Teflon tape and leak check with some dish soap with some gas pressure. Good luck!
@johnmccormick2883Ай бұрын
Many Thanks for this Video! Used the information to understand and repair my icemaker successfully! Instead of buying a $250-$300 replacement icemaker I got the control module off of Amazon for $30 in a day. Excellent Video!
@greezoooАй бұрын
Same dishwasher. Same noise. Took out the pump and disassembled as shown in the video. No blockage. No rubbing. Still Noise 😩Seems to be coming from inside the pump motor. Is it a bearing? Time for a replacement?
@applianceassistantАй бұрын
Sounds like the motor. But you’ve already half way to fixing it! 👍🏼
@user-gb7pj5ox2lАй бұрын
Thanks is a great word, But this vidio was much more helpful than expected. I'll be taking my wife out to eat.
@skagg69Ай бұрын
Can a recalibration be performed on the model shown in this video?
@applianceassistantАй бұрын
I’m not 100% sure. I have never used the recalibration mode on this type of washer. Sorry, I can’t be of more help! Common issues are suspension, center bearing leaks/rust, and the occasional cracked stator.
@BearsNCigarsАй бұрын
My dryer burner comes on for like 30 seconds then goes off. Takes forever to dry its venting great but my lint trap isn’t getting any lint on it to clean off. Has me frazzled. The clothes are super stiff and wrinkly also
@applianceassistantАй бұрын
Sounds like an airflow problem. For some reason the blower is not drawing through the drum well. To the burner this is just like a clogged duct. Check all the air seals for your drum, blower housing, etc. anywhere air can escape the drum apart from where it should be going inside the left back air vent and out the right back air vent, through your lint trap. Hope that helps! Good luck!
@BearsNCigarsАй бұрын
@@applianceassistant awesome will do thank you I’m going to check out it blows out the vent well that’s what had me going nuts
@dorisbrinkerhoff8124Ай бұрын
oh now i feel dumb . it keeps falling out
@roxannevenegas8423Ай бұрын
Hello, great video! I did a diagnostic and came up with a f72. Any suggestions on what to do next? It will not spin at this point
@4homemailАй бұрын
All good but the video didn't show how do you get to the parts? I cannot for the life of me take off the panel to get to the coil without breaking something.
@mrrida503Ай бұрын
Thanx for the info.. I'm about to eat all my food, unplug it, and thaw it out!!! Great excuse to throw a party with friends and pig out!!!!!! 🍤🍖🍗🥩🧀🌮🍕🍻🥂🍾🥃🍺🍹🍸🍷🧊
@applianceassistantАй бұрын
Love it!!!
@CaptainCraigKWMRZ2 ай бұрын
Excellent video!
@libbydeville27032 ай бұрын
My exact refrigerator…wish i personally knew where to start😩
@applianceassistant2 ай бұрын
You can figure it out! I believe in you!
@xmegatoyreview72172 ай бұрын
Got mine doing the test. Do you know how long it's going to take?
@applianceassistant2 ай бұрын
Usually 5-10 minutes.
@sddarkman6192 ай бұрын
mine has no jumper holes the the first ice maker you showed, how do I test it? No Jumper holes.
@applianceassistant2 ай бұрын
I have noticed that on some of the new units. Lame!! It will probably require getting the unit into a diagnostic mode through the main interface. If you can find the service manual for your model it will probably tell you how to test the functionality.
@PreachChristLA2 ай бұрын
Should I be getting a reading from the ignitor on ohms? If I do does it mean it is weak and needs to be replaced? I have a Kenmore 400 series. Thanks and God bless!
@applianceassistant2 ай бұрын
There should be a resistance value on the igniter, not open. Hope that helps some. Good luck!
@ejazbaig56372 ай бұрын
Haier no frost double door model 618SS cooling issue 🥲🥲
@applianceassistant2 ай бұрын
Bummer! The newer units are pretty complicated. Try the unplug and thaw. Possibly a 10 minute unplug to reset the control board, if there is no signs of frost build up. Good luck!
@ejazbaig56372 ай бұрын
Sir, I u unplug it at least 24 hour. But after two days fridge compart and freezer compartment temperature go down 14 'C . And after restart it took 3 to 5 hour to start cooling but later on problem still persists 😢😢
@ejazbaig56372 ай бұрын
If u say so I can send u pics.. glad to see ur response
@applianceassistant2 ай бұрын
If all the fans are working it sounds like you may have a sealed system problem. Not really a DIY repair, fair amount of knowledge and specialty tools are needed. Check the interior fans and make sure the lower condenser coil is clean. That’s about the best you can do before calling for some help. Good luck!
@Sunshiine3053 ай бұрын
OHHHH MY GOD AFTER 3 HOURS IT WOKRED. YOUR VIDEO WAS LEGIT. I FIXED IT ❤❤❤❤❤ THANK YOUUUU. YES IM SHOUTING OF HAPPINESS 🙌🏽🤣🤣
@applianceassistant2 ай бұрын
Hahaha! Glad it helped! 😁
@boitumeloleepile80393 ай бұрын
Good day, what might be the course of error in 4plate touch LG.
@applianceassistant3 ай бұрын
That’s a tough question without some context. I would need the model number and error to have any chance of answering.
@timekabolden53093 ай бұрын
Wow. I felt kike i was in vocay school! 😂😂😂❤❤❤❤
@richardwease60583 ай бұрын
My ice maker arm is stuck on open
@tatianaigrayson3 ай бұрын
Awesome video!!!😊
@davew41103 ай бұрын
Excellent video. Thank you for presenting a very simple, clear, how-to on Whirlpool dryer repair. Great pace and illustrations and probably one of the best how-to videos I have seen. Thank you!
@dennispattarozzi50993 ай бұрын
hanks for the video. Just curious...I have a samsung and the top of the coils keeps icing up with the bottom clean. I felt the heat from the defroster on so I know that works...would the bi-metal thermostat be causing the top to ice up? I can tell its affecting the cooling of the inside
@applianceassistant3 ай бұрын
It could be a coolant flow restriction. I would advise watching it for a while when it’s actually cooling, you should see frost start to accumulate over the entire coil. If not it’s an expensive sealed system repair. Fingers crossed 🤞🏼 If the coil is frosting evenly, I would replace the defrost thermistor sensor, and look for air leaks into the compartment from the room.
@dennispattarozzi50993 ай бұрын
@@applianceassistant everything looks good as far as no air leaks, not to mention it just started this all of a sudden. From videos and reading it seams like the defroster is staying on and not letting it frost over to cool which is why I was looking towards the bi metal thermostat
@applianceassistant3 ай бұрын
If that’s the case, you may want to check the power supply coming from the control board to the defrost circuit. It should not be constant, only temporary when a defrost cycle is being performed. The bi-metal is more of a safety than a control. If the defrost relay on the control is always closed, the control would need to be replaced.
@dennispattarozzi50993 ай бұрын
@@applianceassistant I’ll check again, it may not be on constant because there was ice forming in the drain where the defroster dips into the drain hole. I’ll go over all of it again, the bi metal was a cheap part so I don’t mind changing it anyway. Thanks for the info
@applianceassistant3 ай бұрын
No problem! Best of luck!
@justinphipps99093 ай бұрын
L & M showed no resistance on my ice maker. Took the motor/gear assembly apart and spun the motor with voltmeter set to A/C voltage. The motor generated power so confirmed it was fine. After replacing the control board kit (emitter and receiver), the ice maker started working. It had the 2 flash failure on my Kenmore Coldspot.
@applianceassistant3 ай бұрын
Thanks for sharing your experience! That is strange on the motor test. Maybe there was bad contact from the motor to the test points L&M
@kellybeenguyen23883 ай бұрын
Thanks so much for teaching us how to fix the washing machine.. got jamed.. but it's c8 now.. let's hope it works again. Thanks so much.
@custominvest12703 ай бұрын
best appliance repair video I've ever seen. hands down. Thank you!
@luperebolledo35933 ай бұрын
very helpful hope it will save me some money. thanks
@the_stixXx3 ай бұрын
I've been repairing my own appliances for a while now. This was a great video that gave me information that was useful. Thanks for sharing.
@applianceassistant3 ай бұрын
Glad it was helpful!
@Rae-hy8ez3 ай бұрын
How do you repair the surface on the burner if part of the enamel came off
@applianceassistant3 ай бұрын
Most of this kind of thing is replace the damaged component. There’s not much you can do to repair damaged enamel given the heat tolerance requirements. That I’m aware of. If you figure something out I would love to know about it!
@markvigneaux32463 ай бұрын
How to you remove the ice maker front cover to be able to adjust the water fill. My water flow is too much and it's leaking down after filling with water causing blocks of ice in the ice bin. We have the french door fridge / freezer so not a lot of room to see the 2 screws to loosen and remove the whole ice maker. Is there an easy way to adjust that screw?
@applianceassistant3 ай бұрын
If your ice maker is like this one or a basic Frigidaire model the front cover is just a friction hold. Just grab that thing and pull with conviction. Or you can use a flat head screwdriver and leverage from the small notch that’s usually on the bottom edge. If it keeps leaking after adjustment you probably need to replace the water valve. Good luck!
@GunnerTyler-jd7eu3 ай бұрын
You’re a douche bag you fucking jokes you’re an asshole. Then when you get to the actual point you run through it like fucking 900 miles an hour. What a jackass.