This is the best method , and here is why , I did just the gear delete and at high rpm my balance shafts walked from vibration and started to hit the crank . Now 2nd time I use this method cut my balance shaft off the pump , it runs perfect and no problems .
@nicholasmiller85089 ай бұрын
The only thing that worried me is a tap on that drill, lol! Thanks man, overall great concept, seems as if though it's similar to what iabed does but you cut instead of adding plugs. This would be perfect if you could adapt the 1.8t baffle or other to fit, as you said, for cornering for those interested. Great job.
@flamurislami73233 ай бұрын
Thanks for posting this, balance shafts seized on my 2008 EOS and snaped the bolt on the balance shaft gear, was getting low oil pressure on display when reaching normal operating temp. Followed your steps and working great. Got new bolts from dealer and runing great not getting the low pressure message. Only diffrence I did was pressed the balance shafts out from the other half and just bolted it on the engine. Thanks this video saved me a lot of money I subscribed
@taco8v3 ай бұрын
Glad the worked for you bud , you will notice you car revs faster
@OgTexMusic3 ай бұрын
@@taco8v Hello, I want to try this on my 2008 Passat. But can anyone explain how this fixes low oil pressure? Isnt the oil pump sprocket still tunring the same regardless of removing the balance shaft part of the assembly or not? Can someone please explain. Great video by the way.
@taco8v3 ай бұрын
@OgTexMusic yeah you remind with same sprocket and same set up , but heres the thing . Do to the balance shaft has not bearings between the shaft and housing it will get lose and leak oil pressure down low before it gets up to the head and trigger the oil sensor . Even if the pump is pumping normally if this leak is not fix it will not send good oil pressure up to the head . Hope you understand man
@OgTexMusic3 ай бұрын
@@taco8v yes, I understand now. Thanks. so about 2 years ago I replaced my oil pump/balancer housing. i bought one on ebay for about 400. When I removed the old one it had the broken bolt at the balancer sprocket and the balancers were jammed and very hard to turn. So I put the new oil pump/balancer housing on myself and for about 2 months I thought it was fixed but the low oil pressure warning came back on. Im not sure why the one I bought from ebay would fail so soon but I guess it did. Im hoping I can use the same one and cut it and this will solve my oil pressure problem. And hopefully I dont have the broken sprocket bolt again.
@taco8v3 ай бұрын
Use balance shaft are the same as the one in your car because they wear out But deleting this will get rid of the problem immediately
@lincolndinkin Жыл бұрын
Great Idea! I would maybe bolt up the the other half, to keep the windage under control back there, I think of the crank spinning 4K rpm out in the open back there open to all of the oil draining back down, it might cause aeration in the oil? Just a thought.
@taco8v Жыл бұрын
The crank doesn’t sink in the oil so it hardly touches to create air bubbles Also the oil drain doesn’t drain directly on top of crankshaft.
@italiangirl24402 жыл бұрын
It's amazing how much you know, never stop doing what you're doing. I took my engine apart but I can't get it back together now LOL I just joking😂
@taco8v2 жыл бұрын
👍🏼
@garrettgiuffre72987 ай бұрын
You can get it. Keep at it. It's the only way to learn
@garrettgiuffre72987 ай бұрын
Wonder if this would be the same for the newer tdi
@sandilekhathi50593 ай бұрын
Love this, I had oil pressure issue on my Audi B8, 2010 model. I replaced the oil pump and had the same issue. My engen seized 2 months later. I bought another used engen and I now faced with the same issue. Will this work on a Tsfi, CD engen?
@taco8v3 ай бұрын
If they share the same balance shaft I don’t see why not 👍🏼
@sandilekhathi50593 ай бұрын
Thank you, I will strip and inspect. I will give you feedback. South Africa loves your content. Very informative.
@taco8v3 ай бұрын
Good man share me all over help me grow up in number Maybe in the future if i can afford some giveaways :)
@abderrahmanegouasmi755610 ай бұрын
you are a genious! never mind about others. you have a brain and you know how to use it. i subscribed!
@jayb8941 Жыл бұрын
Genius. Great method 👍🎉
@karimcharifi29716 ай бұрын
Bonjour, t es vraiment trop fort mon ami. Excellente ta vidéo
@taco8v6 ай бұрын
Bonjour 👍🏼
@richiec90775 ай бұрын
I put a used one on two year ago and now I have oil pressure problems again and a high pitch whining from the bottom end , so I'm gonna do this hopefully it works
@taco8v5 ай бұрын
Ohh yeah this will fix it permanently
@adhizzle998510 ай бұрын
good detail, although it seems you don't do much video for mk5? all i see are mk4 and older lol. i like mk5 its lots of room, previous gen a little smaller but weight is less haha
@taco8v10 ай бұрын
I have some posts in my instagram about mk5 stuff like porting heads and cleaning the intake etc
@iqrashabir-ce3lj4 ай бұрын
Will i have to put another chain in if the sprocket has already popped out slightly or would i just delete the shaft and reattach the chain to the guide like you showed in the video ?
@taco8v19 күн бұрын
If is bend or bad yes but if everything looks good i reused
@chrstphrr2 жыл бұрын
Pretty decent mod to avoid the catastrophic failure of the balance shaft / engine. Is this balance shaft mod on this TSI the same approach you would use on the 2.0 BHW TDI found in the B5 Passat?
@taco8v2 жыл бұрын
If is the same balance shaft it can be done yes just need to know the oil ports to plug
@pakkiaman211 ай бұрын
what would be that catastrophic event ? thanks for your reply
@adhizzle998510 ай бұрын
the shafts seize, then no oil pressure i think, and ur engine is toast@@pakkiaman2
@javierdossantosaveiro450111 ай бұрын
Gran trabajo hermano 👏
@chadtennant6719 ай бұрын
Just curious what is the oil pressure like does it make it higher or lower ? If its higher would keeping one of those holes open drop it a little ?
@taco8v9 ай бұрын
Oil pressure doesn’t change its the same and you cannot leave a open hole it will be a oil leak dropping the oil pressure not sending oil to the head and a big boom will happen
@hiltonreniethsaborio8 ай бұрын
Ok 👌 tested and got, now my car has to much power in dow rpm
@taco8v8 ай бұрын
I know deleting this revive the car is like a new car now
@JacobStein13078 ай бұрын
Could you weld the holes shut rather than use bolts and loctite to seal them?
@taco8v8 ай бұрын
Yiu can yeah but this is cast aluminum and it maybe break down the road
@thulanimbhele56162 ай бұрын
Hi. My name is Thulani and I am from South Africa. I did a modification on my oil pump where I had to delete the balance shaft by cutting the small drive shaft pulley. I drove the car for a month after the modification and my car clutch failed. I am not sure if the clutch issue is linked to the modification that I did maybe due to increase in engine vibration. My car still had a dual mass clutch. Is it possible that the two are linked?...Am I suppose to replace a dual mass with a single mass clutch kit after the oil pump modification? since the dual mass is made of springs that might be affected due to increase in vibration?
@taco8v2 ай бұрын
Vibración? What vibración man Deleting the balance shaft doesn’t cause any vibration. Your clutch was probably on the way out and has nothing to do with the modification unless you did something wrong in the process.
@antonovmuminova676010 ай бұрын
Muy buen trabajo😊😊😊😊😊😊
@MeleeTV5 ай бұрын
Salute buddy. Thank you so much
@taco8v5 ай бұрын
Sir your welcome 🙏
@MeleeTV5 ай бұрын
@@taco8v do you still use the washer plate underneath pump to block?
@taco8v5 ай бұрын
@MeleeTV look the video what is did to it .
@mikemarques508 Жыл бұрын
I'm curious how the engine runs. Follow-up video?
@taco8v Жыл бұрын
The car is running fine right now , daily driving it gained a bit more hp and acceleration
@dakotahmartin23172 ай бұрын
Could I use jb weld around the threads
@taco8v2 ай бұрын
Is you car man , me personally won’t trust jb weld inside of a motor
@WickGaming31335 ай бұрын
Does this work for the low oil pressure error? Or is a new oil pump required
@taco8v5 ай бұрын
That is the whole reason man , also do you see me in the video installing a new oil pump?
@dakotahmartin23172 ай бұрын
Why did u send the bolt/screw all the way threw? I did this and I'm still having low oil pressure problems from I'll rev the car up and the red oil light will start flashing and beeping and did u have excessive engine/ rotational noise after doing this cause I do and it doesn't sound to good
@taco8v2 ай бұрын
The bolt is send all the way through to cover both holes at ones . If you don’t cover both sides you will have big leak
@taco8v2 ай бұрын
You definitely don’t do something right here man Or your engine is toast and this method is done to late and now you want to fix it with this method but it’s probably pass the saving point
@dakotahmartin23172 ай бұрын
@taco8v doesn't have Rod knick at all so is it still salvageable I'll pull it apart and redo it threw that hole
@taco8v2 ай бұрын
Yeah plug it
@dakotahmartin23172 ай бұрын
@taco8v it does have a thud noise but I believe it's top end I'll lyk what happens
@anonymous-ace-10 ай бұрын
Hi! If balance shaft deleted,how about a vibration on the engine?
@taco8v10 ай бұрын
The first car i done it was 5 years ago and we gained rpm’s and power
@Benko_DieseL6 ай бұрын
Bro i would like to do this but i am driving extremly fast with my car,will it have any problem if i cut out all this like you did?
@taco8v6 ай бұрын
No problem at all In fact the throttle will be More responsive and you will gain more power too
@Benko_DieseL6 ай бұрын
Would it be more preferable to put like 5w50 or 10w60 oil with this mod?@@taco8v
@taco8v6 ай бұрын
No it be fine with any
@Benko_DieseL6 ай бұрын
Ok so is there anything i should no about this so i can prevent a catastrofical failure or just do the mod and dont worry for anything>?@@taco8v
@aziz-v4x5c6 ай бұрын
Thanks!
@taco8v6 ай бұрын
Appreciated bud 👍🏼
@rbg_industries7 ай бұрын
Chasing tail on oil pressure light new 63000km engine it put light on our shop I took back thay replaced sensor got back same thing within the drive home I took sump off was full of silicone cleaned that still low oil pressure but then other day got 2hours driving no light I'm stumped chain looks tight sprocket in place balance shaft is tight bought oil pressure gauge from fb but it electric if it is Correct it's reading no oil pressure but the gauge could be faulty it makes no ugly sounds is turned off immediately when alarm goes
@Benko_DieseL6 ай бұрын
it can be bacause of chain tensioner there is a little filter that gets clogged and it cant get pressure in it,so change the hole chain assembly on the camshaft and if you oil pump is fine then everything should be good to go
@autobahngringo15 күн бұрын
I would use the FreeWheel method, instead of cutting. 200 bucks!
@taco8v11 күн бұрын
My way is only for whoever wants it for free 🤷♂️ And my video is to show the it can be done at you house in the driveway for free with your own tools . You can do it whatever way you like you want to pay good for you go right ahead buddy 👍🏼😉
@willemvanzyl1982 ай бұрын
This work om a golf 5 gti 2.0L BWA???
@taco8v2 ай бұрын
If engine is the same as the video, i don’t see why not 🤷♂️
@willemvanzyl1982 ай бұрын
@@taco8v thx buddy. Ja its a 2.0L t fsi golf 5 gti bwa. Ill do it tomorrow and give you feedback 😁
@taco8v2 ай бұрын
@willemvanzyl198 ok @Tacovw is my instagram
@catalindinu294415 күн бұрын
@@willemvanzyl198 please tell me if u get it done i have low pressure red light and camshafts weared idk if to change oil pump is needed
@willemvanzyl1982 күн бұрын
@@catalindinu2944hi buddy yes i did the balance shaft delete, and it works 150% i dont have anymore low oil pressure. Aswell as i have more refs. And no vibrations on the motor.
@leedesmond1617 Жыл бұрын
I'll be doing this very soon I'll show you the best way to do it there are many videos also to show you
@taco8v Жыл бұрын
Lets see it , I think you want to use the 1.8t oil pump which i all ready done it . Not one has done it like me by cutting the balance shaft , utilizing the existing oil pump and paying not money for parts Lets see what is best than $0 cost I think you missing the part where it says 0 cost lol
@leedesmond1617 Жыл бұрын
@@taco8v no mate what you have done is going to cause you problems with oil getting to the head and circulating properly. You use the oil pump everything from the 2.0tfsi still you cut x1 cog that's it inside and that stops the balance shaft movement. That pan is there for a reason
@taco8v Жыл бұрын
@leedesmond1617 i have done it before like 9 years ago and the car still working perfectly fine strong 🤷♂️
@taco8v Жыл бұрын
If you refer to the bafle plastic cover the goes under crankshaft and oil pump , older cars doesn’t have it , and they go along just fine , that bafle cover only applies if you racing is when the oil gets into the head but that doesn’t cause problems, its more lubrication to the head lol but seriously i have done this a couple times and has caused 0 problems Infact in all the cases has increased the power and acceleration. Opposite what your saying
@pakkiaman211 ай бұрын
@@taco8v what coudl you say about vibrations ? is it accetable after the mod or not really ? thanks