'09-'14 F150 Fuel Control Module Replacement

Here's the step-by-step process for replacing the Fuel Control Module on your F150.

[@RyanNelson404]

My buddy just replaced this module and his truck fired right up after I forwarded this video. He was panicking about getting to work tomorrow and a 60 dollar part fixed his problem before the dealership wanted 1000+. Thanks OP

[@MadCapCustoms]

Stories like this are why I make videos. Cheers!

[@moogotify]

Fuse was burnt but wasn’t the issue, tried the module next and that was it. Thank you!

[@justicelizana2517]

Shit mine was burnt too I switched and still no start , fuel pump wouldn’t be a complete loss of money tho my gauge doesn’t work

[@janice202]

This is a great step by step explanation!!!

[@richardwheatley8757]

Cleaned throttle body and sensors. Found this did the job perfect, thank you.

[@knk7289]

thanks so much!! same thing was wrong with my f150…. it wouldn’t start… died on me and would stall…. also got horrible gas mileage. this 40 dollar part from ford is the fix

[@nathangenis9664]

Do u have part #?

[@BasedBasset]

I replaced it about a year ago. Truck is now doing the same thing. Did the fuse 27 swap but still not starting (Crank, no start). Is there a way to test this module to see if its bad before I go buy a new one?

[@leftcoast2681]

Dude! Wonderful edit of your original video! (It was @ 13 mins) I sent original video to my buddy, and I literally told him, "It's WAY longer than it needs to be, and could be cut-down to around 5 minutes...but it's a really good 5 minutes!" Thanks!

[@MadCapCustoms]

Which original video are you referring to?

[@pedrolara1169]

Thank you 😊

[@alphaturd6922]

I just changed pump my 09 f150 xlt 5.4 started ran for a second and died now i got crank no start im not sure where the pressure sensor is there isnt one on fuel rail but seems like it is not getting fuel i can hear the pump come on though when i turn the key

[@magictoaster806]

Do you know the dealer part number for this part by any chance?

[@agustinherrera9290]

So even if the fuel pump gets activated when i turn the key on i have to replace this

[@jerrybradford5073]

What were the symptoms you had that made you change it out?

[@ConceptsNCreations]

That is my question too. But seems like he's no going to respond.

[@doobyboy21]

You did not need to get this part programmed ?

[@RobGettings-d7b]

My truck is cranking but not starting, but also not throwing a code. Is it possible for the module to fail without throwing a code?

[@BasedBasset]

Mine did this, no code, but replaced it and truck started right up.

[@FELIXTHECATRAPS]

Thank You! Boss

[@nathangenis9664]

But why does fuse 27 blow up , I’m modded (2012 5.0 ram air intake boss mani headers and tune. I believe I’m having this issue along with fuse 27 melting but thing is I never had this problem when stock

[@BasedBasset]

Ford hired the intern to create that circuit?

[@Jikickz]

Does this fix problem with fuel gauge reading that fuel tank is empty

[@MadCapCustoms]

Most likely not. Probably a stuck float on the in-tank pump assembly

[@rusbus15]

Take a look at the canister purge valve. I was having similar issues, as well as not starting after fueling and that fixed it. Part # CX2695 for a 2014 5.0

[@jeremyrogers9959]

Go with 3 uggaduggas

[@scottwebber652]

Im tryin this rite now n needed to see how the harness comes off.

[@doobiez4057]

I'm dealing with a 2013 that had blew fuse 27 (fuel pump) used starter fluid to get it going until I could replace it. Worked fine but once in a while not start but crank, then fire right up. Now its cold it may take a few primes of ignition to get it started but after that it runs and drives fine. No codes, hope this works.

[@scottwebber652]

Same thing for me on ‘14. I did the same until I I replaced the fpd. Time will tell i guess.

[@nathangenis9664]

Do u have the part # oem

[@huntermadison6900]

Did this fix the intermittent no start Issue. What is a FPD?

[@shadhutchison6578]

how did you know for sure it was the module? My truck turns over but its not starting. Everything sounds normal but not catching.

[@syncronisity1]

Just did the FPDM in my 2013 F-150 FX4. Had a dealership tell me it was the pump itself, so glad I didn't listen to them! 10 minutes of work, and the truck started right up, thanks for making this vid!

[@CaptainRon1913]

Mine just went out. Fried the wire at the fuse box as well.

[@kevingaddis7276]

Thank you for the info and video, helped me out a lot.

[@SuperbLee79]

No programming needed?

[@MadCapCustoms]

nope!

[@73dustpan]

I can not get it to unclip Update. I got it unclipped it was packed with red clay dirt. Had to tap it till I shook all the dirt loose. Horrible location for the thing!

[@scottwebber652]

I have a no start issue with my’14 f150 w/5.0 Any vids to diagnose ?

[@5n34k5]

Was that giving the wrench light

[@CartridgeCalls]

Is this for the 5.0L?